DS90LV031ATMTC - 3.3V Quad LVDS Driver | Texas Instruments
MPN: DS90LV031ATMTC ✗ Akhir HidupDS90LV031ATMTC Ringkasan
An LVDS line driver is a high-speed interface device that converts low-voltage single-ended logic signals into low-voltage differential signals. This differential signaling method supports the LVDS interface layer within point-to-point data links. Compared with conventional single-ended CMOS, differential LVDS improves noise immunity and helps preserve signal integrity over longer cable or board traces.
The DS90LV031A family provides four parallel driver channels in one package. Inputs accept LVTTL or LVCMOS levels, while each output produces a differential LVDS signal with a nominal differential output magnitude of 350 mV. The outputs support tri-state operation, and common enable inputs allow active-low or active-high control of all four channels.
Its low-power CMOS implementation makes the device suitable for systems that need high data throughput without the higher power consumption associated with older high-speed pseudo-ECL interface devices. The quad-channel architecture also reduces the number of interface packages and driver ICs required on a multi-lane board.
Typical uses include point-to-point links between FPGAs, ASICs, DSPs, and test equipment; industrial data acquisition systems; and communications equipment carrying multiple high-speed differential channels. The device can also serve as the transmitting half of a link paired with the DS90LV032A receiver family.
PCB implementation requires careful differential routing, short traces, a continuous reference plane, and symmetrical signal geometry. The output differential impedance must match the selected board media and termination network, while input and enable timing must be checked for the target data rate.
This page consolidates the device function, lifecycle status, package information, comparison parameters, and replacement guidance to support schematic review, PCB compatibility checks, and sourcing decisions for legacy LVDS designs.
Alternatif penggantian untuk DS90LV031ATMTC — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
DS90LV031ATMTC/NOPB
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DS90LV031ATMTCX/NOPB
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SN65LVDS31PWR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DS90LV031ATMTC Spesifikasi
| Device Type | Quad CMOS differential line driver |
| Number of Drivers | 4 channels |
| Tegangan Pemuat | 3.3 V |
| Maximum Data Rate | >400 Mbps |
| Frekuensi Bawah Maximum | >200 MHz |
| Input Signal Type | LVTTL or LVCMOS |
| Output Signal Type | LVDS differential |
| Nominal Differential Output Voltage | 350 mV |
| Output Enable Control | Common active-low or active-high enable |
| Output State | Tri-state |
| Jumlah Pin | 16 pins |
| Paket | 16-pin TSSOP (PW) |
| Tipe Mounting | Surface mount |
| Suhu Kerja | -40°C to +85°C |
| Technology | CMOS |
| Lead-Free Status | Lead-free ordering variant indicated by NOPB suffix |
DS90LV031ATMTC 16-pin tssop (pw) Diamant Konfigurasi Panduan
Konfigurasi pin untuk DS90LV031ATMTC (16-pin tssop (pw) pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk DS90LV031ATMTC.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
DS90LV031ATMTC cocok untuk 6 aplikasis: FPGA Point-to-Point Data Links, Industrial Data Acquisition Systems, Telecommunications Equipment Interfaces, Test and Measurement Equipment, ASIC and DSP Interconnects, Legacy Equipment Maintenance.
FPGA Point-to-Point Data Links
The DS90LV031ATMTC fits high-speed point-to-point links between an FPGA and another digital device when four LVDS transmit channels are required. Its support for rates above 400 Mbps and clock frequencies above 200 MHz provides useful margin for parallel data paths, while differential LVDS output improves noise immunity relative to single-ended CMOS. The four channels are controlled through common enable inputs and can enter a tri-state state when the link is disabled. Board implementation requires constant differential impedance, matched trace lengths, a continuous reference plane, and a termination arrangement compatible with the receiver and board media. The legacy device also offers a documented 16-pin TSSOP replacement path through SN65LVDS31PWR.
Direkomendasikan
Industrial Data Acquisition Systems
The DS90LV031ATMTC is appropriate for industrial data-acquisition equipment that transfers several low-voltage digital channels over a short cable or balanced board interface. Four differential drivers provide noise-tolerant transmission from a controller, sensor interface, or signal-conditioning assembly to a remote receiver. Operation from 3.3 V supports modern control electronics, and the common enable function simplifies coordinated link shutdown. For factory systems, maintain a continuous ground or reference plane beneath the differential pair, avoid discontinuities and test-point stubs, and select the receiver termination to suit the characteristic impedance and cable length.
Direkomendasikan
Telecommunications Equipment Interfaces
The DS90LV031ATMTC can serve as the transmit section of a high-speed communications link in telecommunications and networking equipment. Its above-400-Mbps LVDS performance suits parallel backplanes, point-to-point module interfaces, and control paths that require differential signaling. The four channels allow multiple related signals to leave one package, reducing board area and synchronization complexity. Designers should treat the enable inputs as a shared resource, validate active-high versus active-low polarity in the system controller, and review receiver thresholds and timing margin across the complete cable, connector, and termination path.
Direkomendasikan
Test and Measurement Equipment
The DS90LV031ATMTC is useful in test and measurement instruments that shuttle high-rate digital control data between a controller, fixture, or remote acquisition module. LVDS differential signaling helps maintain data integrity in environments that also contain analog measurement circuitry and switching power converters. Its quad-channel organization supports compact routing, and its tri-state enable control can isolate drivers when the connected receiver is not active. Layout should keep the differential pairs away from noisy power-converter loops and use connector or cable transitions that preserve impedance and symmetrical pair geometry.
Direkomendasikan
ASIC and DSP Interconnects
The DS90LV031ATMTC provides a compact four-lane LVDS transmit interface between an ASIC, DSP, or mixed-signal processor and a high-speed receiver. The device’s CMOS input stage accepts LVTTL or LVCMOS signaling, while its differential outputs support rates above 400 Mbps over suitable PCB or cable interconnects. The shared enable control supports coordinated reset or link isolation, although the designer must verify the polarity used by the host logic. Because the original ordering code is obsolete, validate the exact host timing and enable sequence before adopting SN65LVDS31PWR as a production replacement.
Direkomendasikan
Legacy Equipment Maintenance
The DS90LV031ATMTC is particularly relevant to maintenance and obsolescence programs for legacy industrial, medical, and communications equipment. Rather than redesigning an entire interface section, a qualified same-footprint part can preserve the existing PCB and receiver architecture. The NOPB designation supports lead-free procurement requirements, while SN65LVDS31PWR offers a reported drop-in path for obtaining a more sustainable supply. Replacement approval should include pinout comparison, enable-polarity verification, timing-margin analysis, and thermal verification under the equipment’s maximum ambient temperature.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk DS90LV031ATMTC — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | DS90LV031ATMTC/NOPB | DS90LV031ATMTCX/NOPB | SN65LVDS31PWR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) |
| Function | Quad CMOS LVDS differential line driver | Quad CMOS LVDS differential line driver | Quad CMOS LVDS differential line driver | LVDS differential line driver |
| Output Signal | LVDS differential | LVDS differential | LVDS differential | LVDS differential |
Diferensiator Kunci
- Exact original-family ordering continuity (vsSN65LVDS31PWR)
- Four-channel integration in one package (vsSN65LVDS31PWR)
- Lead-free ordering options (vsSN65LVDS31PWR)
Catatan Desain
Route each LVDS pair as a tightly coupled differential pair over a continuous reference plane. Maintain consistent spacing and geometry across the driver, receiver, connectors, and test points. Avoid routing over split planes, changing layer references, adding unterminated stubs, or passing near switching regulators. These controls reduce impedance discontinuities and limit common-mode conversion that can degrade LVDS signal integrity at the device’s above-400-Mbps capability.
Confirm the complete link configuration before layout, including input thresholds, enable polarity, receiver thresholds, termination, and cable length. The common enables can place all four outputs into tri-state, but their active polarity must match the host logic. During replacement qualification, compare propagation delay, delay skew, output rise and fall behavior, and supply tolerance between DS90LV031ATMTC and SN65LVDS31PWR rather than relying only on matching packages.
Do not treat every 16-pin LVDS device as a pin-compatible substitute. The DS90LV031ATMTC is a four-channel driver with shared enable control; receiver ICs and devices with different channel counts or enable arrangements can require board changes. Before approving SN65LVDS31PWR or any ordering variant, verify every power, ground, input, output, and enable connection against the manufacturer pin-description table and the original schematic.
Use the manufacturer’s recommended supply and layout practices to control CMOS power dissipation and junction temperature. Estimated: at a 3.3 V supply, each active output driver dissipates power according to its CMOS load and output activity; the exact dissipation depends on load capacitance, toggle rate, and enable state and therefore cannot be assigned a single value without circuit conditions. Provide continuous ground-plane copper beneath the TSSOP and evaluate the assembled board at its maximum ambient temperature.
Informasi Konformitas
The NOPB suffix identifies a lead-free ordering option for DS90LV031A-family variants. Specific RoHS, REACH, halogen-free, and conflict-minerals declarations are not stated in the available manufacturer and distributor records.