Texas Instruments

DS90LV031ATMTC - 3.3V Quad LVDS Driver | Texas Instruments

部品番号: DS90LV031ATMTC ✗ 生産終了
3.3 V Vdss 16-pin TSSOP (PW) Package >200 MHz Speed
MOQ: 1 |

DS90LV031ATMTC 概要

The Texas Instruments DS90LV031ATMTC is a 3.3 V quad CMOS differential line driver supporting data rates above 400 Mbps and clock frequencies above 200 MHz through Low Voltage Differential Signaling (LVDS). The device accepts LVTTL or LVCMOS inputs, provides four differential LVDS outputs, and is packaged in a 16-pin TSSOP package.

An LVDS line driver is a high-speed interface device that converts low-voltage single-ended logic signals into low-voltage differential signals. This differential signaling method supports the LVDS interface layer within point-to-point data links. Compared with conventional single-ended CMOS, differential LVDS improves noise immunity and helps preserve signal integrity over longer cable or board traces.

The DS90LV031A family provides four parallel driver channels in one package. Inputs accept LVTTL or LVCMOS levels, while each output produces a differential LVDS signal with a nominal differential output magnitude of 350 mV. The outputs support tri-state operation, and common enable inputs allow active-low or active-high control of all four channels.

Its low-power CMOS implementation makes the device suitable for systems that need high data throughput without the higher power consumption associated with older high-speed pseudo-ECL interface devices. The quad-channel architecture also reduces the number of interface packages and driver ICs required on a multi-lane board.

Typical uses include point-to-point links between FPGAs, ASICs, DSPs, and test equipment; industrial data acquisition systems; and communications equipment carrying multiple high-speed differential channels. The device can also serve as the transmitting half of a link paired with the DS90LV032A receiver family.

PCB implementation requires careful differential routing, short traces, a continuous reference plane, and symmetrical signal geometry. The output differential impedance must match the selected board media and termination network, while input and enable timing must be checked for the target data rate.

This page consolidates the device function, lifecycle status, package information, comparison parameters, and replacement guidance to support schematic review, PCB compatibility checks, and sourcing decisions for legacy LVDS designs.

ドロップイン代替品: DS90LV031ATMTC — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

DS90LV031ATMTC/NOPB

✅ ドロップイン
📦 16-pin TSSOP (PW)
Lead-free NOPB ordering designation; the family remains a 3.3 V, 4-channel driver above 400 Mbps in the same 16-pin TSSOP package, with no stated functional parameter difference.

📋 参考代替品(カタログ未掲載)

DS90LV031ATMTCX/NOPB

✅ ドロップイン
📦 16-pin TSSOP (PW)
Alternate ordering designation for the same 3.3 V, 4-channel, above-400-Mbps LVDS driver in a 16-pin TSSOP package; no functional difference is stated.

📋 参考代替品(カタログ未掲載)

SN65LVDS31PWR

✅ ドロップイン
📦 16-pin TSSOP (PW)
A documented complete replacement with consistent terminals, package, and principal performance characteristics; individual timing and enable values require comparison against the original design.

📋 参考代替品(カタログ未掲載)

DS90LV031ATMTC 仕様

Device Type Quad CMOS differential line driver
Number of Drivers 4 channels
電源電圧 3.3 V
Maximum Data Rate >400 Mbps
最大クロック周波数 >200 MHz
Input Signal Type LVTTL or LVCMOS
Output Signal Type LVDS differential
Nominal Differential Output Voltage 350 mV
Output Enable Control Common active-low or active-high enable
Output State Tri-state
ピン数 16 pins
パッケージ 16-pin TSSOP (PW)
実装タイプ Surface mount
動作温度 -40°C to +85°C
Technology CMOS
Lead-Free Status Lead-free ordering variant indicated by NOPB suffix

DS90LV031ATMTC 16-pin tssop (pw) ピン配置ガイド

DS90LV031ATMTC (16-pin tssop (pw) パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

DS90LV031ATMTC の 16-pin tssop (pw) パッケージピン配置図

詳細なピン配置データはありません: DS90LV031ATMTC.

詳細は データシート をご参照ください。

主な用途

DS90LV031ATMTC の用途: 6 件s: FPGA Point-to-Point Data Links, Industrial Data Acquisition Systems, Telecommunications Equipment Interfaces, Test and Measurement Equipment, ASIC and DSP Interconnects, Legacy Equipment Maintenance.

⚡

FPGA Point-to-Point Data Links

The DS90LV031ATMTC fits high-speed point-to-point links between an FPGA and another digital device when four LVDS transmit channels are required. Its support for rates above 400 Mbps and clock frequencies above 200 MHz provides useful margin for parallel data paths, while differential LVDS output improves noise immunity relative to single-ended CMOS. The four channels are controlled through common enable inputs and can enter a tri-state state when the link is disabled. Board implementation requires constant differential impedance, matched trace lengths, a continuous reference plane, and a termination arrangement compatible with the receiver and board media. The legacy device also offers a documented 16-pin TSSOP replacement path through SN65LVDS31PWR.

🏭

Industrial Data Acquisition Systems

The DS90LV031ATMTC is appropriate for industrial data-acquisition equipment that transfers several low-voltage digital channels over a short cable or balanced board interface. Four differential drivers provide noise-tolerant transmission from a controller, sensor interface, or signal-conditioning assembly to a remote receiver. Operation from 3.3 V supports modern control electronics, and the common enable function simplifies coordinated link shutdown. For factory systems, maintain a continuous ground or reference plane beneath the differential pair, avoid discontinuities and test-point stubs, and select the receiver termination to suit the characteristic impedance and cable length.

🌐

Telecommunications Equipment Interfaces

The DS90LV031ATMTC can serve as the transmit section of a high-speed communications link in telecommunications and networking equipment. Its above-400-Mbps LVDS performance suits parallel backplanes, point-to-point module interfaces, and control paths that require differential signaling. The four channels allow multiple related signals to leave one package, reducing board area and synchronization complexity. Designers should treat the enable inputs as a shared resource, validate active-high versus active-low polarity in the system controller, and review receiver thresholds and timing margin across the complete cable, connector, and termination path.

🔧

Test and Measurement Equipment

The DS90LV031ATMTC is useful in test and measurement instruments that shuttle high-rate digital control data between a controller, fixture, or remote acquisition module. LVDS differential signaling helps maintain data integrity in environments that also contain analog measurement circuitry and switching power converters. Its quad-channel organization supports compact routing, and its tri-state enable control can isolate drivers when the connected receiver is not active. Layout should keep the differential pairs away from noisy power-converter loops and use connector or cable transitions that preserve impedance and symmetrical pair geometry.

🖥️

ASIC and DSP Interconnects

The DS90LV031ATMTC provides a compact four-lane LVDS transmit interface between an ASIC, DSP, or mixed-signal processor and a high-speed receiver. The device’s CMOS input stage accepts LVTTL or LVCMOS signaling, while its differential outputs support rates above 400 Mbps over suitable PCB or cable interconnects. The shared enable control supports coordinated reset or link isolation, although the designer must verify the polarity used by the host logic. Because the original ordering code is obsolete, validate the exact host timing and enable sequence before adopting SN65LVDS31PWR as a production replacement.

🧩

Legacy Equipment Maintenance

The DS90LV031ATMTC is particularly relevant to maintenance and obsolescence programs for legacy industrial, medical, and communications equipment. Rather than redesigning an entire interface section, a qualified same-footprint part can preserve the existing PCB and receiver architecture. The NOPB designation supports lead-free procurement requirements, while SN65LVDS31PWR offers a reported drop-in path for obtaining a more sustainable supply. Replacement approval should include pinout comparison, enable-polarity verification, timing-margin analysis, and thermal verification under the equipment’s maximum ambient temperature.

おすすめ製品の概要

SN65LVDS31PWR Reported 16-pin TSSOP drop-in replacement 使用用途: FPGA Point-to-Point Data Links, Industrial Data Acquisition Systems, Telecommunications Equipment Interfaces, Test and Measurement Equipment, ASIC and DSP Interconnects, Legacy Equipment Maintenance DS90LV031ATMTC/NOPB Lead-free ordering option for the original family 使用用途: FPGA Point-to-Point Data Links, Industrial Data Acquisition Systems, Telecommunications Equipment Interfaces, Test and Measurement Equipment, ASIC and DSP Interconnects, Legacy Equipment Maintenance DS90LV031ATMTCX/NOPB Alternate ordering designation 使用用途: Legacy Equipment Maintenance
Where to buy DS90LV031ATMTC online?
Use the Request a Quote form on this page to request DS90LV031ATMTC availability, order quantities, and current sourcing support for the obsolete 16-pin TSSOP device. Because the part is no longer manufactured, availability can be limited and may depend on remaining original inventory, authorized supply, or an acceptable drop-in replacement such as the SN65LVDS31PWR. Include your required quantity, target date, and whether the original tube packaging is mandatory.
What is the price of DS90LV031ATMTC?
The current commercial price for DS90LV031ATMTC should be confirmed through the Request a Quote form on this page. The device is obsolete, so its value depends on remaining inventory, package quantity, inspection requirements, and whether a functionally equivalent 16-pin TSSOP replacement is acceptable. A quotation will allow the exact obsolete MPN to be separated from the NOPB ordering variant and from the SN65LVDS31PWR replacement option.
What is the lead time for DS90LV031ATMTC?
Lead time for DS90LV031ATMTC depends on remaining supply and should be requested through the Request a Quote form on this page. Since Texas Instruments identifies the original ordering code as obsolete and no longer manufactured, a delivery commitment should not be assumed without written confirmation. Buyers should also specify whether the required quantity is in multiples of the manufacturer’s standard tube quantity and whether an SN65LVDS31PWR substitution is technically acceptable.
Is DS90LV031ATMTC in stock?
DS90LV031ATMTC availability cannot be confirmed without a current inventory response and should be checked through the Request a Quote form on this page. The manufacturer no longer produces the device, so any remaining supply may be limited rather than factory replenishable. If an uninterrupted production program requires a durable supply path, request separate availability and lifecycle details for the SN65LVDS31PWR 16-pin TSSOP alternative.
What is the operating voltage of DS90LV031ATMTC?
The DS90LV031ATMTC operates from a 3.3 V supply and accepts LVTTL or LVCMOS input signals. According to the Texas Instruments DS90LV031A manufacturer datasheet, the quad differential driver supports data rates above 400 Mbps, equivalent to a signaling frequency above 200 MHz. Its four outputs use low-voltage differential signaling with a nominal differential output magnitude of 350 mV.
Where to download the DS90LV031ATMTC datasheet PDF?
The official DS90LV031A manufacturer datasheet is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ds90lv031a.pdf. The DS90LV031ATMTC is an ordering option within the DS90LV031A family, so the family document provides the device description, electrical characteristics, and application information. Use the manufacturer pin-description table when assigning signal names to the 16-pin TSSOP footprint.
Where can I find the DS90LV031ATMTC pinout?
The DS90LV031ATMTC pin assignment is documented in the pin-description section of the Texas Instruments DS90LV031A manufacturer datasheet. The package is a 16-pin TSSOP with four LVDS driver channels, power and ground pins, input data pins, and shared enable inputs. Confirm every signal against the manufacturer pin table before laying out a replacement PCB because the common enable polarity and channel numbering determine the trace connections.
What are the key specifications of DS90LV031ATMTC that engineers should know?
The DS90LV031ATMTC is a 3.3 V, four-channel CMOS LVDS line driver packaged in a 16-pin TSSOP. According to the Texas Instruments DS90LV031A manufacturer datasheet, it supports data rates above 400 Mbps and clock rates above 200 MHz, accepts LVTTL or LVCMOS inputs, provides 350 mV nominal differential output, and includes common tri-state enable control. These characteristics place it in the high-speed point-to-point interface class.
Can SN65LVDS31PWR replace DS90LV031ATMTC?
SN65LVDS31PWR is a reported pin-to-pin 16-pin TSSOP replacement for DS90LV031ATMTC because its terminals, package, and principal performance characteristics are described as consistent. Confirm the complete pinout, enable polarity, supply range, propagation delay, output timing, and propagation delay skew against the original design before substitution. The candidate is listed as a drop-in option here, but production qualification remains the designer’s responsibility.
What can replace the obsolete DS90LV031ATMTC?
The most directly supported replacement is SN65LVDS31PWR, a Texas Instruments 16-pin TSSOP LVDS driver reported as a complete replacement with consistent terminals and principal performance characteristics. The DS90LV031ATMTC/NOPB ordering designation can also address an equivalent lead-free version of the original family. Confirm channel mapping, enable polarity, timing, supply voltage, and footprint in the manufacturer documentation before approving either replacement.
DS90LV031ATMTC vs SN65LVDS31PWR - which is better for a legacy LVDS link?
Choose DS90LV031ATMTC/NOPB when exact continuation of the original DS90LV031A documentation and behavior is the primary requirement. Choose SN65LVDS31PWR when the documented 16-pin TSSOP replacement relationship is acceptable and a currently supported sourcing path is more valuable. The reported match covers package, terminals, and principal performance, but the original signal timing and enable polarity should still be checked against the target schematic.
What is the difference between DS90LV031ATMTC and DS90LV031ATMTC/NOPB?
Both identifiers identify the DS90LV031A quad LVDS line driver in the 16-pin TSSOP family, while the NOPB designation identifies the lead-free ordering option. The functional role remains four differential LVDS outputs above 400 Mbps from LVTTL or LVCMOS inputs. The distinction is primarily the ordering and environmental-material designation, so procurement documents should use the exact approved ordering code required by the BOM.
When should I choose DS90LV031ATMTC over SN65LVDS31PWR?
Choose the original DS90LV031ATMTC or its NOPB ordering option when preserving the original National Semiconductor or Texas Instruments interface behavior is more important than lifecycle continuity. Choose SN65LVDS31PWR when a documented drop-in relationship and a more sustainable supply path justify a timing and enable review. This selection is particularly relevant for production maintenance, industrial control, test equipment, and legacy communications equipment.
Is DS90LV031ATMTC suitable for high-speed FPGA interconnects?
The DS90LV031ATMTC is suitable for point-to-point FPGA links that operate within its specified LVDS interface conditions. According to the Texas Instruments DS90LV031A manufacturer datasheet, the device exceeds 400 Mbps and uses differential outputs for improved noise immunity. The PCB must provide controlled differential impedance, continuous return paths, proper termination, and matched trace geometry, and the complete I/O standard must be compatible with the FPGA interface.
What is the best Analog Devices equivalent for DS90LV031ATMTC?
No Analog Devices part has been established as a confirmed 16-pin TSSOP, pin-to-pin drop-in equivalent for DS90LV031ATMTC. The AD8130 is identified in general equivalence listings, but that does not by itself establish package, pinout, enable, timing, or supply compatibility. Use the Request a Quote form on this page for a controlled cross-reference request, and do not approve a cross-brand substitute without a complete manufacturer-datasheet comparison.

エンジニアリング参考データ: DS90LV031ATMTC — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose DS90LV031ATMTC or its NOPB ordering designation when maintaining the original National Semiconductor or Texas Instruments behavior is the primary requirement and exact continuity with the existing schematic is important. This option preserves the documented 3.3 V supply, four LVDS driver channels, above-400-Mbps data rate, above-200-MHz clock capability, common enable control, and 16-pin TSSOP footprint. Choose SN65LVDS31PWR when the reported pin-to-pin replacement relationship is acceptable and a more sustainable lifecycle path is needed for continued production. Before replacing the obsolete device, compare the complete pinout, active enable polarity, input thresholds, propagation delay, timing skew, output characteristics, and supply range. For a cross-brand substitution, do not rely on a general functional equivalence listing; the package, pin assignment, and timing requirements must be demonstrated by manufacturer documentation and system-level testing.

代替品との比較

パラメータ この製品 DS90LV031ATMTC/NOPB DS90LV031ATMTCX/NOPB SN65LVDS31PWR
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 16-pin TSSOP (PW) 16-pin TSSOP (PW) 16-pin TSSOP (PW) 16-pin TSSOP (PW)
Function Quad CMOS LVDS differential line driver Quad CMOS LVDS differential line driver Quad CMOS LVDS differential line driver LVDS differential line driver
Output Signal LVDS differential LVDS differential LVDS differential LVDS differential

主な差別化要因

  • Exact original-family ordering continuity (vs SN65LVDS31PWR)
  • Four-channel integration in one package (vs SN65LVDS31PWR)
  • Lead-free ordering options (vs SN65LVDS31PWR)

設計ノート

Route each LVDS pair as a tightly coupled differential pair over a continuous reference plane. Maintain consistent spacing and geometry across the driver, receiver, connectors, and test points. Avoid routing over split planes, changing layer references, adding unterminated stubs, or passing near switching regulators. These controls reduce impedance discontinuities and limit common-mode conversion that can degrade LVDS signal integrity at the device’s above-400-Mbps capability.

Confirm the complete link configuration before layout, including input thresholds, enable polarity, receiver thresholds, termination, and cable length. The common enables can place all four outputs into tri-state, but their active polarity must match the host logic. During replacement qualification, compare propagation delay, delay skew, output rise and fall behavior, and supply tolerance between DS90LV031ATMTC and SN65LVDS31PWR rather than relying only on matching packages.

Do not treat every 16-pin LVDS device as a pin-compatible substitute. The DS90LV031ATMTC is a four-channel driver with shared enable control; receiver ICs and devices with different channel counts or enable arrangements can require board changes. Before approving SN65LVDS31PWR or any ordering variant, verify every power, ground, input, output, and enable connection against the manufacturer pin-description table and the original schematic.

Use the manufacturer’s recommended supply and layout practices to control CMOS power dissipation and junction temperature. Estimated: at a 3.3 V supply, each active output driver dissipates power according to its CMOS load and output activity; the exact dissipation depends on load capacitance, toggle rate, and enable state and therefore cannot be assigned a single value without circuit conditions. Provide continuous ground-plane copper beneath the TSSOP and evaluate the assembled board at its maximum ambient temperature.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Yes
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The NOPB suffix identifies a lead-free ordering option for DS90LV031A-family variants. Specific RoHS, REACH, halogen-free, and conflict-minerals declarations are not stated in the available manufacturer and distributor records.

関連検索

ds90lv031atmtc nopb DS90LV031ATMTC datasheet DS90LV031ATMTC datasheet pdf DS90LV031ATMTC pinout DS90LV031ATMTC equivalent DS90LV031ATMTC replacement DS90LV031ATMTC cross reference DS90LV031ATMTC vs SN65LVDS31PWR DS90LV031ATMTC price DS90LV031ATMTC stock Texas Instruments DS90LV031ATMTC DS90LV031ATMTC 16 pin TSSOP DS90LV031ATMTC LVDS driver DS90LV031ATMTC FPGA interface

関連部品&用語

Texas Instruments National Semiconductor DS90LV031ATMTC DS90LV031A DS90LV031ATMTC/NOPB DS90LV031ATMTCX/NOPB SN65LVDS31PWR LVDS Low Voltage Differential Signaling CMOS LVTTL LVCMOS differential line driver interface IC semiconductor 16-pin TSSOP TSSOP package family surface mount SMD 400 Mbps 200 MHz 350 mV tri-state output FPGA point-to-point interface industrial data acquisition
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示