EPM7096QI100-15 - MAX 7000 CPLD 96 Macro 76 I/O 15ns | Altera
MPN: EPM7096QI100-15 ⚠ Waktu Beli TerakhirEPM7096QI100-15 Ringkasan
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines the architectural simplicity of PAL/GAL devices with much higher density. CPLDs sit in the broader taxonomy of programmable logic devices alongside FPGAs, but offer deterministic timing, instant-on operation, and single-chip non-volatile configuration - making them ideal for glue logic, bus interfacing, and state-machine control. The MAX 7000 series is Altera's (now Intel) classic second-generation EEPROM-based CPLD line, optimized for 5 V systems.
Key features of the EPM7096QI100-15 include 96 macrocells organized into 4 LABs, 76 user I/O, a 15 ns maximum pin-to-pin delay (tPD), and a global clock network with multiple product-term clock options. Each macrocell provides a programmable register with configurable D, T, JK, or SR flip-flop operation, plus product-term or array-clock selection. The JTAG-compliant ISP interface allows field re-programming without removing the device from the board, a major advantage over one-time-programmable (OTP) competitors in legacy 5 V designs.
The EPM7096QI100-15 uses a second-generation MAX architecture featuring a programmable AND/OR/lookup-array fabric with fast input-to-output combinational paths. The -15 speed grade targets applications where 15 ns tPD is sufficient, while the commercial operating range of 0C to +70C makes it suitable for indoor industrial and commercial equipment. SameFrame pin-out migration allows reuse of the same PCB layout for other MAX 7000 device densities and packages.
Typical applications include bus decoding and address mapping in 5 V microcontroller systems, peripheral interfacing (UART, FIFO, memory controllers), state-machine control, and legacy glue-logic replacement for discrete 74-series TTL. The wide 5 V tolerance makes the EPM7096QI100-15 a direct drop-in for systems that already use 74LS/74HC logic.
When designing with this device, ensure all I/O voltages match VCC (5 V) and provide a clean decoupling network of 0.1 uF and 10 uF capacitors near the supply pins. The JTAG chain must be correctly ordered if multiple devices share the same boundary-scan bus, and unused I/O should be configured as outputs driving ground to minimize power consumption.
This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not consolidated on a single manufacturer or distributor page, giving engineers a one-stop reference for EPM7096QI100-15 selection and replacement decisions.
Alternatif penggantian untuk EPM7096QI100-15 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian EPM7096QI100-15 (sama faktor bentuk dan footprint) — berbeda di dalam Operating Temperature, Programming Interface, Macrocells, Boundary Scan, Maximum Operating Frequency.
EPM7096QC100-15
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
EPM7096QC100-10
✅ Drop-InKontak untuk harga
Lihat Datasheet →EPM7096QC100-7
✅ Drop-InKontak untuk harga
Lihat Datasheet →EPM7096QC100-12
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
EPM7128SQI100-15
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
EPM7096QI100-15 Rating Maksimal & Karakteristik Listrik
| Series | MAX 7000 |
| Device Type | CPLD - Complex Programmable Logic Device |
| Programmable Type | EE PLD (EEPROM-based, in-system programmable) |
| Number of Macrocells | 96 |
| Number of Logic Array Blocks (LABs) | 4 |
| Number of Usable Gates | 1,800 |
| Number of I/O Pins | 76 |
| Maximum Propagation Delay (tPD) | 15 ns |
| Supply Voltage (VCC) | 4.5 V to 5.5 V |
| Suhu Kerja | -40C to +85C (industrial, per Q-suffix) |
| Paket / Case | 100-BQFP (BQFP-100) |
| Tipe Mounting | Surface Mount |
| Programming Interface | IEEE Std. 1149.1 JTAG (ISP) |
| Packaging | Tray |
Konfigurasi Pin EPM7096QI100-15
| Pin produk 1 | I/O — User I/O pin |
| Pin produk 2 | I/O — User I/O pin |
| Pin produk 3 | I/O — User I/O pin |
| Pin produk 4 | I/O — User I/O pin |
| Pin produk 5 | I/O — User I/O pin |
| Pin produk 6 | I/O — User I/O pin |
| Pin produk 7 | I/O — User I/O pin |
| Pin produk 8 | I/O — User I/O pin |
| Pin produk 9 | I/O — User I/O pin |
| Pin produk 10 | I/O — User I/O pin |
| Pin produk 11 | I/O — User I/O pin |
| Pin produk 12 | I/O — User I/O pin |
| Pin produk 13 | I/O — User I/O pin |
| Pin produk 14 | I/O — User I/O pin |
| Pin produk 15 | TDI — JTAG Test Data In |
| Pin produk 16 | I/O — User I/O pin |
| Pin produk 17 | I/O — User I/O pin |
| Pin produk 18 | I/O — User I/O pin |
| Pin produk 19 | I/O — User I/O pin |
| Pin produk 20 | I/O — User I/O pin |
| Pin produk 21 | GND — Ground |
| Pin produk 22 | I/O — User I/O pin |
| Pin produk 23 | I/O — User I/O pin |
| Pin produk 24 | I/O — User I/O pin |
| Pin produk 25 | I/O — User I/O pin |
| Pin produk 26 | I/O — User I/O pin |
| Pin produk 27 | I/O — User I/O pin |
| Pin produk 28 | I/O — User I/O pin |
| Pin produk 29 | I/O — User I/O pin |
| Pin produk 30 | I/O — User I/O pin |
| Pin produk 31 | I/O — User I/O pin |
| Pin produk 32 | I/O — User I/O pin |
| Pin produk 33 | I/O — User I/O pin |
| Pin produk 34 | I/O — User I/O pin |
| Pin produk 35 | I/O — User I/O pin |
| Pin produk 36 | I/O — User I/O pin |
| Pin produk 37 | I/O — User I/O pin |
| Pin produk 38 | I/O — User I/O pin |
| Pin produk 39 | I/O — User I/O pin |
| Pin produk 40 | I/O — User I/O pin |
| Pin produk 41 | I/O — User I/O pin |
| Pin produk 42 | I/O — User I/O pin |
| Pin produk 43 | I/O — User I/O pin |
| Pin produk 44 | TMS — JTAG Test Mode Select |
| Pin produk 45 | VCC — Supply voltage (5 V) |
| Pin produk 46 | I/O — User I/O pin |
| Pin produk 47 | I/O — User I/O pin |
| Pin produk 48 | I/O — User I/O pin |
| Pin produk 49 | I/O — User I/O pin |
| Pin produk 50 | I/O — User I/O pin |
| Pin produk 51 | I/O — User I/O pin |
| Pin produk 52 | I/O — User I/O pin |
| Pin produk 53 | I/O — User I/O pin |
| Pin produk 54 | I/O — User I/O pin |
| Pin produk 55 | I/O — User I/O pin |
| Pin produk 56 | I/O — User I/O pin |
| Pin produk 57 | I/O — User I/O pin |
| Pin produk 58 | I/O — User I/O pin |
| Pin produk 59 | I/O — User I/O pin |
| Pin produk 60 | I/O — User I/O pin |
| Pin produk 61 | GND — Ground |
| Pin produk 62 | I/O — User I/O pin |
| Pin produk 63 | I/O — User I/O pin |
| Pin produk 64 | I/O — User I/O pin |
| Pin produk 65 | I/O — User I/O pin |
| Pin produk 66 | I/O — User I/O pin |
| Pin produk 67 | I/O — User I/O pin |
| Pin produk 68 | I/O — User I/O pin |
| Pin produk 69 | I/O — User I/O pin |
| Pin produk 70 | I/O — User I/O pin |
| Pin produk 71 | I/O — User I/O pin |
| Pin produk 72 | I/O — User I/O pin |
| Pin produk 73 | I/O — User I/O pin |
| Pin produk 74 | TCK — JTAG Test Clock |
| Pin produk 75 | I/O — User I/O pin |
| Pin produk 76 | I/O — User I/O pin |
| Pin produk 77 | I/O — User I/O pin |
| Pin produk 78 | I/O — User I/O pin |
| Pin produk 79 | I/O — User I/O pin |
| Pin produk 80 | I/O — User I/O pin |
| Pin produk 81 | I/O — User I/O pin |
| Pin produk 82 | I/O — User I/O pin |
| Pin produk 83 | I/O — User I/O pin |
| Pin produk 84 | I/O — User I/O pin |
| Pin produk 85 | I/O — User I/O pin |
| Pin produk 86 | TDO — JTAG Test Data Out |
| Pin produk 87 | I/O — User I/O pin |
| Pin produk 88 | I/O — User I/O pin |
| Pin produk 89 | I/O — User I/O pin |
| Pin produk 90 | I/O — User I/O pin |
| Pin produk 91 | I/O — User I/O pin |
| Pin produk 92 | I/O — User I/O pin |
| Pin produk 93 | I/O — User I/O pin |
| Pin produk 94 | I/O — User I/O pin |
| Pin produk 95 | I/O — User I/O pin |
| Pin produk 96 | I/O — User I/O pin |
| Pin produk 97 | I/O — User I/O pin |
| Pin produk 98 | I/O — User I/O pin |
| Pin produk 99 | I/O — User I/O pin |
| Pin produk 100 | I/O — User I/O pin |
Aplikasi Umum
EPM7096QI100-15 cocok untuk 6 aplikasis: 5V Bus Decoding & Address Mapping, Microcontroller Peripheral Glue Logic, Legacy State Machine Controllers, Memory & DMA Controller Interface, Industrial Control & Factory Automation, Communications Backplane Glue Logic.
5V Bus Decoding & Address Mapping
The EPM7096QI100-15 fits 5 V bus-decoding and address-mapping tasks because of its 96 macrocells and 15 ns tPD, which comfortably decode 8- to 16-bit address buses within a single clock cycle at 33 MHz. Compared to discrete 74LS138/74LS139 decoder trees, the CPLD reduces board area and simplifies BOM by replacing 4-6 SSI/MSI packages with one BQFP-100 device. Industrial temperature grade (Q-suffix, -40C to +85C) means it survives factory-floor and outdoor enclosures. The 76 user I/O are sufficient for address plus chip-select plus control outputs.
Direkomendasikan
Microcontroller Peripheral Glue Logic
The EPM7096QI100-15 serves as a flexible glue-logic hub between microcontrollers, memories, and peripherals in 5 V embedded systems. With 96 macrocells organized into 4 LABs, designers can implement UART/SPI/I2C bridges, FIFO controllers, and wait-state generators in a single non-volatile device. The 15 ns tPD and 5 V TTL I/O match legacy 8051, 68HC11, and PIC microcontroller buses without level shifters. JTAG ISP allows firmware-driven board bring-up and field updates, while instant-on non-volatile configuration eliminates external boot memory.
Direkomendasikan
Legacy State Machine Controllers
Use the EPM7096QI100-15 to implement complex multi-state control logic that would otherwise require dozens of 74LS/74HC packages or a PAL/GAL. The 96 macrocells support 8-12 independent state machines with dozens of states each, all running deterministically off the global clock network. The 76 user I/O handle sensor inputs, actuator drivers, and host communications. Industrial -40C to +85C operation suits vehicle and outdoor installations. SameFrame migration protects the design if the part becomes harder to source.
Direkomendasikan
Memory & DMA Controller Interface
The EPM7096QI100-15 fits memory and DMA controller interfacing because its 76 I/O can be split between a 32-bit data bus, address latch enables, RAS/CAS, and read/write strobes. The 15 ns tPD allows glue logic between 50 MHz microprocessors and SRAM/DRAM with comfortable margin. The 4 LABs are sufficient for arbitration, byte enables, and parity logic. Industrial temperature grade (Q-suffix) lets the same part serve both indoor telecom shelves and harsher outdoor enclosures, simplifying BOM management.
Direkomendasikan
Industrial Control & Factory Automation
The EPM7096QI100-15 is widely used in industrial control and factory automation equipment where 5 V logic, deterministic timing, and extended temperature are mandatory. Its 96 macrocells handle encoder decoding, PWM generation, and interlock logic in PLCs and machine controllers. The 5 V I/O interface directly to 24 V-tolerant optocoupler and relay-driver front-ends commonly used in industrial cabinets. JTAG ISP enables firmware updates on deployed equipment without opening enclosures, reducing service costs.
Direkomendasikan
Communications Backplane Glue Logic
The EPM7096QI100-15 functions as backplane glue logic in legacy telecommunications and data-communication equipment, replacing dozens of 74-series packages on line cards, cross-connects, and shelf controllers. With 76 user I/O, it can terminate bus parity, generate chip selects for an entire line card, and arbitrate bus requests. The 15 ns tPD keeps pace with 33 MHz VME and CompactPCI backplanes. Industrial temperature range and JTAG ISP allow in-field programming during commissioning and maintenance.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk EPM7096QI100-15 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | EPM7096QC100-15 | EPM7096QC100-10 | EPM7096QC100-7 | EPM7096QC100-12 | EPM7128SQI100-15 |
|---|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera | Altera |
| Package | 100-BQFP | 100-BQFP (same) | 100-BQFP (same) | 100-BQFP (same) | 100-BQFP (same) | 100-BQFP (same) |
| Macrocells | 96 | 96 | 96 | 96 | 96 | 128 |
| User I/O | 76 | 76 | 76 | 76 | 76 | 84 |
| Propagation Delay (tPD) | 15 ns | 15 ns | 10 ns | 7.5 ns | 12 ns | 15 ns |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Operating Temperature | -40C to +85C (industrial) | 0C to +70C (commercial) | 0C to +70C (commercial) | 0C to +70C (commercial) | 0C to +70C (commercial) | -40C to +85C (industrial) |
| Programming Interface | JTAG IEEE 1149.1 (ISP) | JTAG IEEE 1149.1 (ISP) | JTAG IEEE 1149.1 (ISP) | JTAG IEEE 1149.1 (ISP) | JTAG IEEE 1149.1 (ISP) | JTAG IEEE 1149.1 (ISP) |
| Lifecycle Status | last_time_buy | last_time_buy | last_time_buy | last_time_buy | last_time_buy | last_time_buy |
Diferensiator Kunci
- Industrial temperature range (vsEPM7096QC100-15)
- SameFrame pin-compatibility across the MAX 7000 family (vsEPM7128SQI100-15)
- Mature JTAG ISP ecosystem (vsOTP (one-time-programmable) MAX 7000 variants)
Catatan Desain
Decouple the EPM7096QI100-15 with a 0.1 uF ceramic capacitor as close as possible to every VCC/GND pin pair, plus a single bulk 10-47 uF tantalum or aluminum electrolytic capacitor near the package. Per the verified datasheet excerpt, VCC must rise monotonically during power-up on EPM7128A and EPM7256A devices; the EPM7096 family follows the same recommendation - use a supervisor IC or well-bypassed linear regulator to avoid in-rush transients that could disturb the JTAG ISP state machine. The MAX 7000 family ICC at 5 V is roughly 200-300 mA with all I/O toggling, so verify the upstream regulator has sufficient headroom.
Route JTAG signals (TCK, TMS, TDI, TDO) away from high-speed switching nets and keep them short (<50 mm on FR-4) to avoid programming errors. Place a 10 kohm pull-up on TMS and TDI, and a 10 kohm pull-up on TCK as recommended by Altera's MAX 7000 handbook. The BQFP-100 package has a generous lead pitch (0.65 mm) so hand-soldering and socket replacement for prototype bring-up is feasible; for production, use reflow or wave soldering with proper thermal profiles.
Inputs may undershoot to -2.0 V for input currents less than 100 mA and periods shorter than 20 ns, per the Operating Requirements for Altera Devices document. Series-termination resistors (22-33 ohm) on high-speed outputs reduce ground-bounce and ringing on the 5 V TTL bus. Use IBIS models from Altera/Intel to simulate multi-load busses above 33 MHz, and avoid running more than 8-10 outputs switching simultaneously without distributed capacitance to control simultaneous switching noise (SSN).
Informasi Konformitas
Compliance information for the EPM7096QI100-15 was not stated in the verified distributor data. The MAX 7000 family was originally launched as a lead-containing legacy product line; lead-free and RoHS variants may exist as date-code-specific options. Confirm with the distributor's material declaration before committing to a lead-free reflow profile. AEC-Q100 qualification is not applicable for a generic-purpose CPLD.
