Renesas Electronics

ICS621MIT - 1:4 200MHz Clock Buffer | Renesas Electronics

MPN: ICS621MIT ✓ Aktif
8-SOIC Package 200 MHz Speed
MOQ: 1 |

ICS621MIT Ringkasan

Renesas Electronics ICS621MIT is a low-skew 1-to-4 clock buffer operating up to 200 MHz in an 8-SOIC package. It accepts one clock input and provides four buffered clock outputs, allowing a single low-frequency source to drive multiple timing-critical loads while reducing fanout loading. The 8-SOIC package is a surface-mount option for compact digital, communications, networking, and test equipment designs.

A clock buffer is a digital timing IC that reproduces a clock signal through one or more output stages. Clock buffers and clock drivers belong to the broader clock and timing IC category, where their practical role is to isolate a source from capacitive loading, extend signal reach, and distribute a common timing reference. In a multi-load system, a buffer helps each receiver see a cleaner transition sequence than it would when connected directly to a long or heavily loaded clock trace.

The principal characteristics of ICS621MIT are its 1:4 fanout ratio, 200 MHz maximum clock frequency, low-skew architecture, and 8-SOIC package. A 1:4 ratio means that one incoming clock can feed four output branches, reducing the number of separate distribution stages required in a moderate-complexity system. The 200 MHz operating capability makes the device relevant to designs carrying clock signals in the hundreds-of-megahertz range, subject to the complete electrical limits and layout guidance in the manufacturer datasheet.

Because the ICS621MIT performs digital fanout rather than voltage conversion, its signal path is intended to preserve clock timing relationships across the four outputs. Low skew is particularly relevant when multiple receivers must operate from the same edge, including parallel data converters, sequential logic, communications equipment, and automated test systems. The exact propagation-delay, output-impedance, rise-time, fall-time, supply-voltage, and temperature limits should be taken directly from the 621 datasheet before final timing and power-budget calculations.

Typical uses include clock distribution for communication equipment, fanout in network interfaces, test-and-measurement systems, and synchronization among multiple digital subsystems. It can also serve as an interface between a central clock source and several low-to-moderate-capacitance loads when the board requires a dedicated fanout stage. Its eight-pin package also keeps the footprint compact while exposing one input, four outputs, power connections, and ground in a conventional small-outline arrangement.

Layout should prioritize short clock traces, a continuous ground reference, and placement of the device near the clock source or the group of receivers it serves. Avoid routing sensitive clock nets beneath unrelated noisy circuitry, and terminate or control unused outputs according to the manufacturer's guidance. Validate timing at the intended frequency, load capacitance, supply voltage, temperature, and process corner because fanout buffers can change edge rate and edge-to-edge alignment as loading changes.

This product page combines the core device identity, verified manufacturer documentation, a same-package replacement candidate, application-oriented engineering guidance, and a structured comparison of the information needed for clock-tree design. It is intended to help engineers identify whether the 1:4, 200 MHz ICS621MIT architecture fits a board before undertaking detailed datasheet verification and board-level qualification.

Alternatif penggantian untuk ICS621MIT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian ICS621MIT (sama faktor bentuk dan footprint) — berbeda di dalam Package.

Renesas Electronics
Package: 8-SOIC (0.154 inch, 3.90 mm width)
Bandingkan dengan ICS621MIT →

ICS621MI

✅ Drop-In
Renesas Electronics
📦 8-SOIC
Clock fanout buffer · 1:4 · 200 MHz · 1 V to 1.8 V · 3.3 V tolerant · 4 · 1 · Low skew

Kontak untuk harga

ICS621MIT Spesifikasi

Product Type Low-skew clock buffer
Fanout Ratio 1:4
Frekuensi Bawah Maximum 200 MHz
Number of Clock Inputs 1 input
Number of Clock Outputs 4 outputs
Logic Type Logic clock buffer
Paket 8-SOIC
Tipe Mounting Surface mount

ICS621MIT 8-soic Diamant Konfigurasi Panduan

Konfigurasi pin untuk ICS621MIT (8-soic pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai 8-soic untuk ICS621MIT

Tidak ada data diatribut pin yang tersedia untuk ICS621MIT.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

ICS621MIT cocok untuk 6 aplikasis: Telecommunications Clock Distribution, Network Interface Clock Fanout, Test and Measurement Systems, Parallel Data Converter Synchronization, Industrial Control Module Timing, Server and Storage Interface Clocking.

🌐

Telecommunications Clock Distribution

ICS621MIT fits telecommunications equipment requiring one master clock to feed several digital subsystems without connecting every receiver directly to the source. Its 1:4 fanout provides four buffered branches, while the 200 MHz operating limit accommodates high-speed digital clock trees. Place the device near the central clock distribution point, provide a continuous ground plane, and keep each output route short. Confirm input thresholds, output levels, propagation delay, and permitted capacitive loading in the Renesas Electronics 621 datasheet before assigning receivers to individual outputs.

🌐

Network Interface Clock Fanout

ICS621MIT can distribute a common interface clock among multiple network-facing logic blocks within a line card or communications module. The 1:4 ratio provides a practical fanout stage for systems that need more than two synchronized destinations, and the low-skew architecture helps preserve edge alignment between parallel receivers. Keep the buffer close to the clock source, avoid long branches, and maintain a continuous reference plane beneath the clock routes. Validate output loading and worst-case timing at the intended 200 MHz operating point or lower system frequency.

🖥️

Test and Measurement Systems

ICS621MIT is applicable in test and measurement equipment where a timing reference must drive several acquisition, conversion, or control sections from one source. Its four outputs support a moderate fanout architecture, and its maximum 200 MHz frequency covers clocking requirements common to high-speed digital test systems. Route outputs directly toward the intended loads, maintain consistent return paths, and avoid sharing sensitive clock traces with noisy switching nodes. Timing margin should be evaluated across load, process, voltage, and temperature conditions using the complete manufacturer electrical tables.

📺

Parallel Data Converter Synchronization

ICS621MIT can provide a common sampling or conversion clock to four parallel receiver groups when a board requires isolated fanout from a central oscillator or PLL. The 1:4 configuration reduces the number of connections to the original clock source, while the low-skew characteristic supports relative timing between output branches. Keep all four routes similarly terminated and use a low-impedance ground reference to limit edge distortion. Confirm the maximum permissible output capacitance, output transition behavior, and data-converter setup and hold requirements before release to production.

🏭

Industrial Control Module Timing

ICS621MIT is suitable for industrial control modules that must distribute a common clock to processors, counters, communication controllers, or programmable logic. Its 1:4 fanout provides a simple centralized clock tree, and the 200 MHz ceiling permits use in faster digital control domains when system requirements stay within the device limits. Place the buffer at the clock-tree junction, keep stubs short, and avoid routing beneath power converters or motor-control switching nodes. Verify supply voltage, noise margins, temperature range, and timing tolerance for the enclosure environment.

🖥️

Server and Storage Interface Clocking

ICS621MIT can serve as a local fanout stage in server, storage, or peripheral-interface circuitry where one clock must reach several digital loads. The four-output configuration allows separate routing strategies for closely and remotely placed receivers, while low skew is important when downstream logic depends on common clock edges. Use a careful hierarchy of clock branches rather than long daisy-chained traces, and account for receiver capacitance at each output. Confirm that the 200 MHz limit, supply requirements, and environmental ratings match the system clock and chassis conditions.

What is the ICS621MIT clock buffer?
The ICS621MIT is a Renesas Electronics low-skew 1-to-4 clock buffer with a maximum operating frequency of 200 MHz. It accepts one clock input and provides four buffered outputs in an 8-SOIC surface-mount package. According to the Renesas Electronics 621 datasheet, the device is intended for low-skew clock distribution where one source must drive multiple loads.
What are the key specifications of ICS621MIT that engineers should know?
The key ICS621MIT specifications are its 1:4 fanout ratio, 200 MHz maximum clock frequency, low-skew clock-buffer function, and 8-SOIC package. These characteristics place it in the clock and timing IC category and allow one clock source to feed four branches. The Renesas Electronics 621 datasheet remains the controlling reference for supply voltage, propagation delay, output skew, and loading limits.
Where can I download the ICS621MIT datasheet PDF?
The official Renesas Electronics 621 datasheet is available at the manufacturer document page on this product page. It is the best source for the ICS621MIT pin description, electrical characteristics, timing diagrams, recommended operating conditions, and package drawings. Use the manufacturer document rather than secondary summaries when defining production test limits or confirming board-level constraints.
Where can I find the ICS621MIT pinout?
The ICS621MIT uses an 8-SOIC package, and its authoritative pin assignment is shown in the Renesas Electronics 621 datasheet. Use the pin-description table and package drawing when assigning the single clock input, four outputs, supply pins, and ground. Because individual pin names are not listed in the available product excerpts, use the manufacturer diagram directly before routing a PCB.
Can ICS621MIT distribute a 200 MHz clock?
Yes. ICS621MIT is specified as a clock buffer capable of operating up to 200 MHz and provides a 1:4 fanout arrangement. The Renesas Electronics 621 datasheet identifies it as a low-skew 1-to-4 clock buffer. Actual timing performance still depends on the clock source, output loading, supply voltage, board topology, and receiver requirements.
What is the difference between ICS621MIT and ICS621MI?
ICS621MIT and ICS621MI are members of the same Renesas Electronics clock-buffer family and are both associated with the 8-SOIC implementation. The available product information distinguishes ICS621MIT as the ordered MPN and ICS621MI as another ordering designation, but it does not expose a complete electrical comparison. Check the manufacturer ordering table and datasheet before treating either suffix as a drop-in substitute.
What can replace ICS621MIT?
ICS621MI is the closest identified same-package candidate, but it should be treated as a conditional replacement rather than an automatically interchangeable part. Both parts are listed with the 8-SOIC clock-buffer family and the related ICS621MI listing identifies a 1:4, 200 MHz clock fanout buffer. Confirm pin assignment, supply limits, timing, lifecycle status, and ordering code against the Renesas Electronics 621 datasheet before substitution.
Is ICS621MI a drop-in replacement for ICS621MIT?
ICS621MI may serve as a same-package replacement candidate, but final approval depends on the manufacturer ordering information and complete datasheet comparison. The available listing describes ICS621MI as a 1:4, 200 MHz clock fanout buffer in an 8-SOIC package. Verify every pin, voltage rating, timing parameter, and package drawing before using it as a production drop-in replacement for ICS621MIT.
When should I choose ICS621MIT over another clock buffer?
Choose ICS621MIT when the design needs a one-to-four clock fanout stage operating up to 200 MHz in an 8-SOIC package and requires a low-skew architecture. It is especially relevant when four receivers need a common clock source. Select another device if the system needs a different fanout ratio, logic level, supply range, output-edge performance, package, or a part with current lifecycle assurance.
Is ICS621MIT suitable for communication and networking equipment?
ICS621MIT is suitable for clock distribution in communication and networking equipment when the system clock is within its 200 MHz capability and the electrical operating limits are satisfied. Its 1:4 fanout can distribute one source to four receiver groups while reducing direct loading on that source. Confirm voltage levels, timing margin, output capacitance, and system-level clock topology in the manufacturer datasheet.
How should the ICS621MIT output loading be designed?
Design each ICS621MIT output around the maximum output capacitance and timing limits defined in the Renesas Electronics 621 datasheet. Keep traces short, provide a solid ground reference, and avoid adding excessive stubs or long branches to a single output. If the intended receiver load is unusually capacitive, use a separate distribution stage or a dedicated clock driver rather than relying on general buffer guidance.
Does ICS621MIT require a heatsink?
The ICS621MIT datasheet excerpts do not state a package thermal resistance, maximum junction temperature, or power dissipation limit, so a definitive heatsink decision cannot be made from the available information. Because it is an 8-SOIC digital clock buffer, thermal requirements depend on supply voltage, output loading, switching activity, ambient temperature, and copper area. Calculate worst-case dissipation using the manufacturer electrical limits.
Where can I buy ICS621MIT online?
Use the Request a Quote form on this page to request current availability, lead time, order quantity, and commercial terms for ICS621MIT. The form allows engineers to obtain a product-specific quotation without relying on changing marketplace listings. Confirm the exact 8-SOIC ordering code, delivery packaging, and lot requirements before releasing a purchase order.
What is the price of ICS621MIT?
Current pricing for ICS621MIT should be obtained through the Request a Quote form on this page because quotation terms can change with quantity, inventory, and delivery requirements. The form supports a direct purchase inquiry for the exact MPN. No static price should be used for budgeting until the quotation confirms the required quantity and commercial terms.
What is the lead time and stock status for ICS621MIT?
Use the Request a Quote form on this page to request the current lead time, available stock, minimum order quantity, and scheduled delivery information for ICS621MIT. Availability can vary by lot and shipment quantity, so an inventory statement should be tied to a confirmed purchase order. The form is the appropriate channel for current sourcing and production-planning answers.

Data referensi engineering untuk ICS621MIT — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose ICS621MIT when the board needs a one-input, four-output clock fanout stage rated up to 200 MHz in an 8-SOIC package. It is particularly appropriate when four receiver groups need a common timing source and the system can satisfy the device's electrical and loading requirements. ICS621MI is the closest identified same-package candidate and should be considered when procurement or ordering-code requirements favor that variant, but it requires final pin, timing, voltage, lifecycle, and qualification checks. Choose a different clock buffer if the design requires another fanout ratio, a different logic standard, differential clock outputs, adjustable delay, lower skew, enhanced supply tolerance, or a package with a larger pin count. For any substitution, validate the manufacturer datasheet, compare worst-case timing at the actual load, and confirm that every receiver remains within the output capacitance and edge-rate limits.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini ICS621MI
Brand Renesas Electronics Renesas Electronics
Package 8-SOIC 8-SOIC
Product Type Low-skew clock buffer Clock fanout buffer
Fanout Ratio 1:4 1:4
Maximum Clock Frequency 200 MHz 200 MHz

Diferensiator Kunci

  • Provides four clock branches from one input (vsICS621MI)
  • Supports clock frequencies up to 200 MHz (vsICS621MI)
  • Uses a compact 8-SOIC footprint (vsICS621MI)
  • Low-skew clock distribution (vsICS621MI)

Catatan Desain

Place the ICS621MIT close to the point where the clock branches diverge. Route each output directly to its intended load, minimize stubs, and maintain a continuous ground reference beneath the clock network. If a receiver is physically distant, use an additional clock distribution stage rather than extending one output into a long branched route. This preserves control over edge rate, capacitance, and inter-output timing.

Validate the clock network at the intended frequency with realistic receiver and board capacitance. The 200 MHz rating identifies the device's maximum clock capability, but usable timing margin also depends on output loading, source edge rate, trace geometry, return path continuity, and the receiver's setup and hold requirements. Evaluate the worst operating corner and avoid using the device near its frequency limit without timing analysis.

Decouple the device according to the Renesas Electronics 621 datasheet, using short supply and ground connections and placing bypass capacitance close to the relevant pins. Confirm the package drawing and pin table before layout because individual pin numbers are not present in the available excerpts. Keep the clock buffer separated from high-current switching paths and maintain symmetrical clock routing where output-to-output timing matters.

Do not assume that any same-package clock buffer is electrically interchangeable. Before substituting another MPN, compare supply voltage, logic thresholds, propagation delay, output skew, output impedance, loading capability, operating temperature, and lifecycle status. Also confirm whether an output is actively held low when disabled or only weakly pulled down, because that behavior affects startup and test-system control.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements are present in the available product documentation excerpts. AEC-Q100 is not applicable to this general-purpose clock buffer.

Data disahkan pada: 2026-11-11 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

ICS621MIT datasheet ICS621MIT pinout ICS621MIT datasheet pdf ICS621MIT equivalent ICS621MIT replacement ICS621MIT cross reference ICS621MIT footprint ICS621MIT price ICS621MIT stock Renesas ICS621MIT ICS621MIT 200MHz clock buffer ICS621MIT 8-SOIC pinout ICS621MIT vs ICS621MI ICS621MIT clock fanout application

Komponen dan Istilah Terkait

Renesas Electronics ICS621MIT ICS621MI Integrated Device Technology IDT clock buffer clock fanout buffer clock driver clock and timing IC digital timing IC semiconductor 1:4 fanout 200 MHz clock low-skew architecture output skew propagation delay 8-SOIC SOIC family surface-mount package SMD clock distribution network interface test and measurement industrial control telecommunications equipment
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ