Texas Instruments

INA2126E/250 - Dual 36V Micropower Instrumentation Amplifier

MPN: INA2126E/250 ✓ Aktif
36 V Vdss 175 µA per channel Id 16-pin SSOP (DBQ) Package
MOQ: 1 |

INA2126E/250 Ringkasan

Texas Instruments INA2126E/250 is a dual-channel, micropower precision instrumentation amplifier with 36 V maximum supply, 175 µA quiescent current per channel, and 250 µV maximum offset. The device is offered in a 16-pin SSOP package and is designed for low-noise differential-signal acquisition. It accepts operating supply voltages from ±1.35 V to ±18 V.

An instrumentation amplifier is a specialized analog amplifier that measures the voltage difference between two input signals while rejecting common-mode interference. The INA2126 family uses a two-op-amp architecture to provide differential input, high input impedance, and straightforward gain selection with an external resistor. Within the signal-chain hierarchy, it belongs to the instrumentation-amplifier class, amplifier IC category, analog signal-conditioning family, and broader semiconductor category.

The INA2126E/250 combines a 36 V supply range with low quiescent current, making it useful in portable instrumentation, battery-powered measurement systems, and industrial data-acquisition equipment. Its two amplifier channels can acquire independent differential signals, while the differential topology helps suppress common-mode voltage present on both inputs. Gain is established with an external resistor, allowing the circuit designer to select the required signal gain without changing the internal amplifier architecture.

According to the Texas Instruments INAx126 family datasheet, the device uses a two-op-amp design and consumes 175 µA per channel. The low input bias current and high input impedance help prevent the source sensor from being heavily loaded. This is particularly important for high-impedance transducers, resistive sensors, and bridge-based measurements where input loading can otherwise change the detected voltage and degrade accuracy.

Typical uses include low-voltage current sensing, portable medical instrumentation, industrial pressure and temperature acquisition, sensor-interface circuits, and precision differential measurement systems. The dual-channel configuration is useful when a design must monitor two related signals, such as a differential sensor output and a reference or diagnostic channel, while preserving independent gain-setting resistors for each amplifier.

For stable operation, place supply-decoupling capacitors close to the supply pins and route each differential input as a compact pair to minimize noise pickup. Select the external gain resistor with suitable tolerance and low temperature coefficient, verify input and output common-mode limits at the intended supply voltage, and ensure the reference pin is driven with a low-impedance source when a nonzero midpoint voltage is required.

This product page consolidates the device function, operating limits, package information, sourcing paths, drop-in family alternatives, comparison parameters, and practical circuit-design guidance. It supports faster engineering selection by connecting the INA2126E/250’s low-power precision characteristics with the signal-chain requirements of portable instrumentation and low-level differential-sensor designs.

Alternatif penggantian untuk INA2126E/250 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

INA2126EA/2K5G4

✅ Drop-In
📦 SSOP-16
Same INA2126 dual family and 16-pin SSOP class; the retrieved record does not quantify the orderable-code parameter differences

📋 Alternatif referensi (tidak dalam katalog)

INA2126UA/2K5E4

✅ Drop-In
📦 SSOP-16
Same INA2126 dual family and 16-pin SSOP class; gain or orderable-code differences are not quantified in the cross-reference record

📋 Alternatif referensi (tidak dalam katalog)

INA2126UAG4

✅ Drop-In
📦 SSOP-16
Same INA2126 dual family and 16-pin SSOP class; the available record does not quantify differences in gain or temperature grade

📋 Alternatif referensi (tidak dalam katalog)

INA2126E/250 Rating Maksimal & Karakteristik Listrik

Amplifier Type Dual precision instrumentation amplifier
Number of Channels 2 channels
Maximum Supply Voltage 36 V
Supply Voltage Range ±1.35 V to ±18 V
Arus Memerintah 175 µA per channel
Offset Voltage 250 µV maximum
Internal Architecture Two-op-amp instrumentation amplifier
Gain Set by an external resistor
Input Type Differential
Paket 16-pin SSOP (DBQ)
Tipe Mounting Surface mount

INA2126E/250 16-pin ssop (dbq) Diamant Konfigurasi Panduan

Konfigurasi pin untuk INA2126E/250 (16-pin ssop (dbq) pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.

Diamant diagram pakai pakai 16-pin ssop (dbq) untuk INA2126E/250

Tidak ada data diatribut pin yang tersedia untuk INA2126E/250.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

INA2126E/250 cocok untuk 6 aplikasis: Portable Differential Sensor Acquisition, Industrial Current-Sense Measurement, Medical Signal Conditioning, Bridge-Based Pressure Measurement, Precision Test and Measurement, Two-Channel Data Acquisition.

📱

Portable Differential Sensor Acquisition

The INA2126E/250 fits portable instrumentation because its 175 µA per-channel quiescent current reduces the power burden of two continuously active measurement channels. Each channel can acquire a differential sensor signal while rejecting common-mode voltage present on both inputs. The 250 µV maximum offset is particularly useful when the measured differential level is small, because it limits the input-referred error before amplification. Install the device close to the sensor connector, use short differential traces, and select the external gain resistor according to the INAx126 gain table. Battery life remains dependent on the sensor itself, so power-saving control of the amplifier system can provide a larger system-level improvement.

🏭

Industrial Current-Sense Measurement

The INA2126E/250 is appropriate for industrial current measurement when the shunt differential voltage must be amplified in the presence of a larger common-mode potential. Its differential input architecture reduces sensitivity to voltage shared by both sense nodes, while the dual-channel arrangement allows a second channel to monitor a complementary measurement or diagnostic signal. The 36 V maximum supply rating supports instrumentation operating above conventional ±5 V rails, although the actual input common-mode and output-swing limits must be respected. Place the amplifier across the shunt Kelvin connections and avoid sharing high-current paths with sensitive input traces to prevent voltage drops from appearing as measurement error.

💊

Medical Signal Conditioning

The INA2126E/250 can condition low-level differential signals in portable medical equipment when both low power and precision are design priorities. Its 250 µV maximum offset helps preserve accuracy at small input levels, while the dual configuration can process a measurement channel and a reference or auxiliary channel. The two-op-amp instrumentation-amplifier topology provides high input impedance and common-mode rejection without requiring the system to match a discrete op-amp network. Designers must still verify electrode-generated input levels, input protection, isolation requirements, leakage behavior, and applicable medical-system standards. The amplifier should be paired with suitable protection and acquisition circuitry rather than treated as a complete medical front end.

🧩

Bridge-Based Pressure Measurement

The INA2126E/250 is well matched to resistive bridge sensing because the differential input can receive the bridge excitation voltage while subtracting the common reference present on both bridge nodes. With 175 µA per channel, it adds low quiescent demand to a portable pressure or force-monitoring system, and the 250 µV maximum offset limits a significant source of low-level measurement error. Select the gain to maximize the bridge differential output within the amplifier’s output-swing limits. Place the amplifier near the bridge connections, maintain symmetric routing, and provide local supply bypassing to prevent excitation and digital activity from adding noise to the small differential result.

🔧

Precision Test and Measurement

The INA2126E/250 can serve as the analog front end of a compact precision measurement instrument, especially when two low-level differential channels must be handled without continuous high power consumption. Its instrumentation-amplifier configuration reduces common-mode error and simplifies gain implementation to one external resistor per channel. A system can apply the measured signal to a high-resolution converter while using the second channel for reference, calibration, or diagnostic information. For laboratory-grade accuracy, verify resistor tolerance, input bias-current effects, source impedance, frequency response, and output settling. The combination of low offset and low quiescent current supports battery-powered field instruments as well as fixed test equipment.

🖥️

Two-Channel Data Acquisition

The INA2126E/250 provides two independent precision instrumentation-amplifier channels in one 16-pin SSOP, making it useful for compact two-channel data-acquisition systems. Both channels share the same family-level low-noise, low-quiescent-current characteristics while allowing separate external gain resistors. This supports measurement of a primary differential sensor and a secondary reference, diagnostic, or complementary sensor without using two discrete amplifier packages. The 36 V maximum supply provides headroom for industrial signal levels, but each channel must remain within its own common-mode and output-swing limits. Routing each differential pair symmetrically and decoupling the supplies close to the device helps preserve the benefit of the instrumentation-amplifier topology.

What is the INA2126E/250?
The INA2126E/250 is a dual-channel, 36 V micropower precision instrumentation amplifier from Texas Instruments. It uses a two-op-amp architecture, operates from ±1.35 V to ±18 V, consumes 175 µA per channel, and provides 250 µV maximum offset. The device is packaged in a 16-pin SSOP and is intended for accurate, low-noise differential-signal acquisition.
What are the key specifications of INA2126E/250 that engineers should know?
The principal INA2126E/250 specifications are two amplifier channels, a 36 V maximum supply, ±1.35 V to ±18 V operating range, 175 µA quiescent current per channel, and 250 µV maximum offset voltage. According to the Texas Instruments INAx126 family datasheet, the part uses a two-op-amp design, supports resistor-programmed gain, and is offered in a 16-pin SSOP package.
Where can I download the INA2126E/250 datasheet PDF?
The official INA2126E/250 datasheet can be downloaded from the Texas Instruments INA2126 documentation page at https://www.ti.com/lit/gpn/INA2126. This manufacturer-hosted PDF contains the family description, electrical characteristics, application information, pin relationships, and ordering details. Use the INA2126 family document because INA2126 is identified as the applicable product family.
Where can I find the INA2126E/250 pinout?
The INA2126E/250 pinout is shown in the Pin Configuration and Pin Functions sections of the Texas Instruments INAx126 family datasheet. The exact orderable device uses a 16-pin SSOP package identified as DBQ. Use the pin-description table for PCB routing because the dual instrumentation-amplifier package includes supply, reference, gain-resistor, input, and output connections.
What supply voltage range does INA2126E/250 support?
The INA2126E/250 supports an operating supply range of ±1.35 V to ±18 V, equivalent to a total span of 2.7 V to 36 V. The manufacturer identifies the device as a 36 V micropower instrumentation amplifier. Designers should also verify signal common-mode range and output-swing limits against the actual supply voltage in the manufacturer electrical-characteristics table.
How much current does INA2126E/250 consume?
The INA2126E/250 consumes 175 µA per channel under the manufacturer’s stated operating conditions. This low channel current supports portable instrumentation and battery-powered acquisition systems. According to the Texas Instruments INAx126 family datasheet, the low quiescent current is combined with a wide ±1.35 V to ±18 V operating range, allowing the same precision amplifier family to address portable and higher-voltage instrumentation systems.
Is INA2126E/250 suitable for low-level sensor measurements?
Yes, the INA2126E/250 is suitable for low-level differential measurements because its differential input architecture is designed to reject common-mode interference and its offset voltage is specified at 250 µV maximum. The device can measure signals from resistive, bridge-based, or current-shunt sensors when the input common-mode voltage, output swing, bandwidth, and gain requirements are checked against the operating conditions.
How is gain configured on the INA2126E/250?
Gain on the INA2126E/250 is set with an external resistor connected to the gain-setting pin of each amplifier. The two-op-amp instrumentation-amplifier architecture lets the circuit designer select gain without changing the internal signal path. Use the gain equation and recommended resistor values in the Texas Instruments INAx126 datasheet, and account for resistor tolerance and temperature coefficient when high-accuracy gain is required.
What is the difference between INA2126E/250 and INA2126EA/2K5G4?
INA2126E/250 and INA2126EA/2K5G4 belong to the same Texas Instruments INA2126 dual instrumentation-amplifier family, but the available comparison records do not expose enough detailed parameter differences to quantify them safely. Both are associated with 16-pin SSOP-class configurations in the retrieved records. Confirm the exact gain, offset, temperature grade, and orderable pin configuration against the current manufacturer datasheet before substitution.
When should I choose INA2126E/250 over another INA2126 variant?
Choose INA2126E/250 when the design requires a dual, 16-pin SSOP instrumentation amplifier with a 36 V maximum supply, 175 µA per channel, and 250 µV maximum offset. Select another INA2126 orderable option only when its gain setting, temperature grade, packaging code, or specific electrical limits better match the production requirement. The alternatives listed for this page preserve the family and package focus rather than substituting unrelated amplifiers.
What is the best drop-in replacement for INA2126E/250?
The closest supported replacements are the same-family, 16-pin SSOP variants INA2126EA/2K5G4, INA2126UA/2K5E4, and INA2126UAG4 identified in the family cross-reference records. Their exact gain, temperature grade, offset limits, and marking should be checked against the production BOM because those orderable-code details are not fully stated in the retrieved comparison records. No unrelated amplifier is presented as a drop-in option.
Can INA2126UA/2K5E4 replace INA2126E/250?
INA2126UA/2K5E4 is a same-family candidate associated with the INA2126 16-pin SSOP lineup and is the closest drop-in candidate in the cross-reference records. It is not automatically a production-approved substitute because orderable codes can encode gain, temperature grade, and packaging details. Compare the exact INA2126U specifications with the INA2126E requirements and confirm both the PCB footprint and gain configuration before substitution.
What can replace INA2126E/250 in an existing design?
A replacement for INA2126E/250 should be a dual INA2126-family device in the same 16-pin SSOP footprint with compatible gain, supply, common-mode, output-swing, and temperature requirements. The cross-reference records identify INA2126EA/2K5G4, INA2126UA/2K5E4, and INA2126UAG4 as the closest family candidates. Verify their orderable specifications and PCB assignments before changing the BOM.
Where can I buy INA2126E/250 and request a quote?
Use the Request a Quote form on this XAIPART product page to request current INA2126E/250 pricing, stock confirmation, minimum order quantity, and lead time. The orderable device is the Texas Instruments INA2126E/250 in a 16-pin SSOP package. Quote requests are the appropriate route for checking current commercial availability without relying on stale price or inventory information.
Is INA2126E/250 active and available for new designs?
The Texas Instruments product page lists INA2126E/250 as part of the current INA2126 family, and the device remains listed for order as a 16-pin SSOP instrumentation amplifier. Current production status, regional stock, and lead time can change, so use the Request a Quote form for an order-specific confirmation. The manufacturer’s product and part-details pages are the authoritative lifecycle references.
Does INA2126E/250 meet RoHS, REACH, and AEC-Q100 requirements?
RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status are not stated in the retrieved technical records, so these requirements should not be assumed. Review the current Texas Instruments INA2126 product-page compliance fields or request the relevant quality documentation for the exact orderable part. The INA2126E/250 is an instrumentation amplifier, so automotive qualification would only apply if it is explicitly designated for that use.

Data referensi engineering untuk INA2126E/250 — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose INA2126E/250 for a dual-channel, low-power precision measurement design that requires 16-pin SSOP packaging, up to a 36 V supply, 175 µA per channel, and 250 µV maximum offset. The listed alternatives remain within the INA2126 family and preserve the closest package and architecture fit, making them preferable to unrelated instrumentation amplifiers when an orderable-code change is acceptable. However, verify gain configuration, temperature grade, exact electrical limits, and pin assignments before replacing the target. For new two-channel designs, begin with INA2126E/250 when its stated operating envelope matches the signal chain. If a candidate’s offset, supply, or temperature limits differ materially, confirm those values against the manufacturer datasheet and complete a signal-chain-level comparison before release.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini INA2126EA/2K5G4 INA2126UA/2K5E4 INA2126UAG4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package SSOP-16 SSOP-16 SSOP-16 SSOP-16
Amplifier Configuration Dual instrumentation amplifier Dual instrumentation amplifier Dual instrumentation amplifier Dual instrumentation amplifier
Internal Architecture Two-op-amp architecture Two-op-amp INA2126 family architecture Two-op-amp INA2126 family architecture Two-op-amp INA2126 family architecture
Gain Configuration External resistor External resistor External resistor External resistor
Special Ordering Information INA2126E/250 orderable code INA2126EA/2K5G4 orderable code INA2126UA/2K5E4 orderable code INA2126UAG4 orderable code

Diferensiator Kunci

  • Dual precision channels in one 16-pin SSOP (vsINA2126UA/2K5E4)
  • Low 175 µA per-channel quiescent current (vsINA2126EA/2K5G4)
  • 36 V maximum supply with 250 µV maximum offset (vsINA2126UAG4)

Catatan Desain

Route each differential input as a closely coupled pair from the source or connector to the amplifier. Keep the pair short, avoid crossing unrelated high-current or switching paths, and establish a nearby ground reference. Symmetrical routing limits conversion of common-mode noise into differential error and preserves the common-mode rejection advantage of the instrumentation-amplifier topology.

Place the supply-bypass capacitor immediately beside the device supply pins and connect it with the shortest practical traces. The INA2126E/250 supports operation from ±1.35 V to ±18 V, but the selected supply must also satisfy the input common-mode range and output-swing requirements. Account for supply ripple, startup behavior, and the 175 µA per-channel quiescent current when sizing the power budget.

Do not assume that identical package names guarantee identical function. Orderable-code differences can encode gain, temperature grade, or production configuration. Before replacing INA2126E/250 with INA2126EA/2K5G4, INA2126UA/2K5E4, or INA2126UAG4, compare the exact gain setting, electrical limits, temperature grade, pin functions, and marking in the manufacturer datasheet.

Use a low-tolerance, low-temperature-coefficient external gain resistor when measurement accuracy depends on gain stability. Evaluate the gain resistor’s contribution to noise and drift, maintain a consistent layout for both channels when they measure related signals, and treat the reference connection as a sensitive node. Any nonzero reference voltage should be generated by a low-impedance source and adequately decoupled.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The retrieved INA2126 product records do not explicitly state the target orderable part’s compliance status. Confirm current quality and environmental documentation with Texas Instruments.

Pencarian Terkait

INA2126E/250 datasheet INA2126E/250 pinout INA2126E/250 datasheet pdf INA2126E/250 equivalent INA2126E/250 replacement INA2126E/250 cross reference INA2126E/250 SSOP-16 Texas Instruments INA2126E/250 INA2126E/250 price INA2126E/250 stock INA2126E/250 application circuit INA2126E/250 vs INA2126UA/2K5E4 36V micropower instrumentation amplifier INA2126E/250 product details

Komponen dan Istilah Terkait

Texas Instruments INA2126E/250 INA2126EA/2K5G4 INA2126UA/2K5E4 INA2126UAG4 INA2126 INAx126 dual instrumentation amplifier instrumentation amplifier precision amplifier analog signal conditioning two-op-amp architecture differential input common-mode rejection low-dropout SSOP-16 SSOP surface-mount package semiconductor 175 µA per channel 250 µV offset 36 V supply external gain resistor portable instrumentation industrial data acquisition
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ