Renesas Electronics

ISL83483IB - 3.3V 250kbps RS-485/RS-422 Transceiver | Renesas

MPN: ISL83483IB ✓ Aktif
3 V to 3.6 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC, 3.6 mm wide body Package
MOQ: 1 |

ISL83483IB Ringkasan

The Renesas Electronics ISL83483IB is a 3.3 V, half-duplex RS-485 and RS-422 differential line transceiver operating at up to 250 kbps in an 8-pin SOIC package. It combines a low-power BiCMOS implementation with slew-rate-limited driver outputs, helping reduce electromagnetic interference and minimize reflections on improperly terminated cables. The device accepts a 3 V to 3.6 V supply and is intended for industrial balanced-communication systems.

An RS-485/RS-422 transceiver is an interface IC that converts between logic-level signals and balanced differential signals used for robust data transmission. RS-422 supports point-to-point, full-duplex links, while RS-485 commonly supports multidrop half-duplex buses. The ISL83483IB multiplexes its driver and receiver paths for half-duplex communication, making it useful where one pair of bus conductors serves both directions.

The principal feature of the ISL83483IB is its 250 kbps slew-rate-limited operation. Limiting the driver edge rate reduces high-frequency harmonics and associated EMI. The manufacturer also identifies the device as meeting both RS-485 and RS-422 requirements. Its 3 V to 3.6 V operating range accommodates regulated 3.3 V systems with the specified supply tolerance.

In half-duplex operation, the transceiver changes direction between transmission and reception. The receiver provides a logic-level output for the host controller, while the driver sends complementary differential voltage onto the bus. Because a single device must manage both functions, interface timing and bus direction control remain important parts of the surrounding firmware and circuitry.

Typical uses include industrial control links, factory automation equipment, building automation, instrumentation, and other balanced serial networks operating at modest data rates. The ISL83483IB is particularly suitable where low EMI is more important than maximum line rate, or where long cables and imperfect terminations can produce reflections.

The PCB layout should preserve the differential pair as a continuous, impedance-controlled route from the transceiver to the connector. Place termination, protection, and bus-surge components close to the line interface, while keeping switching regulators and high-current return paths away from the receiver input. Use the manufacturer pin-description and recommended-circuit guidance when assigning traces and selecting bypass capacitance.

This page combines the manufacturer interface description, package identification, operating limits, drop-in alternatives, and application guidance to support schematic capture, PCB design, sourcing, and lifecycle review of the ISL83483IB.

Alternatif penggantian untuk ISL83483IB — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian ISL83483IB (sama faktor bentuk dan footprint) — berbeda di dalam Package, Supply Voltage Range.

Renesas Electronics
Package: 8-SOIC (IB) 3.9 mm
Supply Voltage Range: 3.0 V to 3.6 V
Bandingkan dengan ISL83483IB →

ISL83485IBZ-T

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
Renesas Electronics
📦 8-pin SOIC
Transceiver · 1/1 · Half · RS-422, RS-485 · 10 Mbps · 3.3 V · 3.0 V to 3.6 V · 1/8 unit-load (up to 256 nodes)

Kontak untuk harga

Lihat Datasheet →

ISL83483IBZ-T

✅ Drop-In
📦 8-pin SOIC
Same 250 kbps RS-485/RS-422 interface and 8-pin SOIC footprint; ordering suffix identifies the production package or shipment format

📋 Alternatif referensi (tidak dalam katalog)

ISL83483IB Spesifikasi

Product Type Half-duplex RS-485/RS-422 differential transceiver
Supply Voltage Range 3 V to 3.6 V
Nominal Supply Voltage 3.3 V
Maximum Data Rate 250 kbps
Communication Mode Half-duplex
Supported Standards RS-485 and RS-422
Driver Architecture BiCMOS slew-rate-limited output
Transceiver Configuration Single transmitter/receiver
Paket 8-pin SOIC, 3.6 mm wide body
Tipe Mounting Surface mount

ISL83483IB 8-pin soic, 3.6 mm wide body Diamant Konfigurasi Panduan

Konfigurasi pin untuk ISL83483IB (8-pin soic, 3.6 mm wide body pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai 8-pin soic, 3.6 mm wide body untuk ISL83483IB

Tidak ada data diatribut pin yang tersedia untuk ISL83483IB.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

ISL83483IB cocok untuk 6 aplikasis: Industrial PLC Serial Links, Factory Automation Equipment, Building Automation Networks, Instrumentation and Test Equipment, Data Acquisition Modules, Remote Sensor Networks.

🏭

Industrial PLC Serial Links

The ISL83483IB fits half-duplex communication between an industrial controller and remote I/O or field equipment operating at up to 250 kbps. Its 3 V to 3.6 V supply range suits regulated 3.3 V control electronics, while the slew-rate-limited BiCMOS driver reduces fast edge-rate energy and associated EMI. The transmitter and receiver share the bus in half-duplex mode, so the host controller must manage direction timing and turnaround without colliding with another transmitter. Cable length, topology, common-mode range, and termination should be checked against the manufacturer electrical limits before deployment.

🏭

Factory Automation Equipment

The ISL83483IB supports balanced half-duplex links between factory sensors, actuators, and automation controllers where moderate data throughput and controlled emissions are important. Operation up to 250 kbps is sufficient for command, status, and configuration traffic, while the slew-rate-limited driver helps suppress reflections on cables with imperfect termination. A 3.3 V supply supports compact controller boards, and the 8-pin SOIC package simplifies routing on mixed-signal control hardware. Use surge protection at exposed cable entries and maintain the differential pair’s geometry through the protection network.

🧩

Building Automation Networks

The ISL83483IB can bridge a 3.3 V controller to RS-485-compatible building automation equipment such as distributed sensors, HVAC interfaces, or access-control panels. Its 250 kbps limit accommodates supervisory control and status traffic, and the controlled output transition rate reduces EMI in panels containing switching power supplies and display electronics. The half-duplex arrangement conserves interface pins by sharing the differential bus for transmission and reception. Verify the selected bus topology, termination arrangement, and operating temperature against the manufacturer specifications before installation.

🔧

Instrumentation and Test Equipment

The ISL83483IB is suitable for laboratory and process-instrumentation modules that exchange measurement commands and results over a balanced RS-485 or RS-422 link. Its 250 kbps slew-rate-limited operation reduces radiated emissions and ringing in compact instruments where long internal cable runs may be unavoidable. The 3.3 V operating range aligns with modern mixed-signal instrumentation, while half-duplex control simplifies bus sharing. Shielding, common-mode grounding, and transient protection remain important when the instrument connects to external equipment through user-accessible cables.

📡

Data Acquisition Modules

The ISL83483IB enables a distributed data-acquisition module to report samples, configuration, and diagnostics over a half-duplex RS-485 bus. A 250 kbps rate is appropriate for many sensor and monitor networks that prioritize deterministic communication and low EMI over maximum throughput. The transceiver operates from a 3 V to 3.6 V supply and fits an 8-pin SOIC footprint, making it practical for compact multi-channel boards. Care should be taken to isolate high-impedance sensors from the communication ground and to validate common-mode margins at the longest cable lengths.

🌐

Remote Sensor Networks

The ISL83483IB suits remote sensor nodes that communicate over a shared RS-485 bus using 3.3 V logic. Its low data rate is sufficient for periodic environmental, position, or equipment measurements, and the slew-limited output helps control emissions in distributed cable installations. Because operation is half-duplex, the node must assert driver enable only when the bus is idle and must detect communication errors through its protocol or receiver status. External protection is advisable at the cable connector, and the differential route should remain symmetrical to avoid converting common-mode noise into receiver errors.

What is the operating voltage of ISL83483IB?
The ISL83483IB operates from 3 V to 3.6 V and is intended for nominal 3.3 V equipment. Renesas describes the ISL83483 family as specified for 3.3 V power with a 10% supply tolerance, which defines the 3 V to 3.6 V operating range. Use a regulated 3.3 V rail and verify the local power rail remains inside this range during startup, load transients, and line activity.
What is the maximum data rate of ISL83483IB?
The ISL83483IB supports data rates up to 250 kbps. Its slew-rate-limited BiCMOS driver reduces fast edge-rate energy and helps limit EMI and cable reflections. The manufacturer lists the device as a 3.3 V, half-duplex, 250 kbps RS-485/RS-422 transceiver. This rate is appropriate for industrial control, automation, and instrumentation links where moderate throughput and reduced emissions are priorities.
Where can I download the ISL83483IB datasheet PDF?
The official ISL83483IB datasheet is available from Renesas through the ISL83483, ISL83485, ISL83488, ISL83490, and ISL83491 family datasheet page. The document contains the electrical characteristics, pin descriptions, interface behavior, and application information needed for schematic and layout work. A distributor-hosted copy can also be used for reference, but the manufacturer document should be the controlling source for production design.
Where can I find the ISL83483IB pinout?
The ISL83483IB pin assignment is shown in the pin-description section of the Renesas ISL83483 family datasheet. The device uses an 8-pin SOIC package and multiplexes its receive and transmit paths for half-duplex operation. Use the numbered package drawing when routing the differential bus, logic-level data lines, direction control, enable, and supply connections; verify every net against the current manufacturer document.
Is ISL83483IB suitable for RS-422 and RS-485 networks?
Yes, the ISL83483IB is designed for both RS-485 and RS-422 balanced communication. Its half-duplex configuration suits multidrop RS-485 buses, while RS-422 point-to-point links can also use the transceiver when the system timing is arranged correctly. The Renesas product description explicitly identifies compliance with both standards and a maximum signaling rate of 250 kbps.
What can replace the ISL83483IB?
The closest supported replacement is another member of the Renesas ISL83483/ISL83485 half-duplex family when its drive rate and pin configuration match the original design. A replacement should preserve the 8-pin SOIC footprint, 3 V to 3.6 V supply range, RS-485/RS-422 function, and required bus timing. Use the manufacturer cross-reference tool and compare every electrical limit before approving a substitution.
IS ISL83483IB the same as ISL83485?
No, the ISL83483 and ISL83485 belong to the same Renesas half-duplex transceiver family but do not have identical operating characteristics. The ISL83483 is identified specifically as a 250 kbps slew-rate-limited device, while the ISL83485 offers a higher-speed operating option. Choose ISL83485 when the interface requires faster data transfer and verify that the alternate speed does not increase EMI or reflections.
When should I choose ISL83483IB over a faster RS-485 transceiver?
Choose the ISL83483IB when the bus operates at or below 250 kbps and reduced EMI is a primary design goal. Its slew-rate-limited output is intentionally slower than high-speed RS-485 devices, which can help limit edge-rate harmonics and ringing on longer or imperfectly terminated cables. A faster transceiver is preferable only when throughput requirements exceed 250 kbps and the completed channel can control reflections.
What is the best RS-485 transceiver for low-EMI industrial links?
The ISL83483IB is a strong fit for a 3.3 V industrial link requiring up to 250 kbps and controlled driver edges. Renesas specifically identifies the slew-rate-limited ISL83483 and ISL83488 devices as reducing EMI and minimizing reflections from improperly terminated cables. Actual suitability still depends on cable length, topology, termination, protection requirements, and timing margin.
Is ISL83483IB in stock and what is its lead time?
Current stock and lead time should be confirmed through the Request a Quote form on this page because inventory can change quickly by region and order quantity. The form should be completed with the exact ISL83483IB ordering code, target quantity, and required delivery date. This avoids committing to a generic half-duplex transceiver variant that may use a different package or tape-and-reel suffix.
Where can I buy ISL83483IB and check the price?
Use the Request a Quote form on this page to request ISL83483IB pricing, stock, minimum order quantity, and lead time. Enter the exact MPN and intended package variant so the quotation matches the assembled board. Commercial terms and availability can change, so obtain a current quotation rather than relying on historical catalog figures.
What is the price of ISL83483IB?
The current ISL83483IB price is best requested through the Request a Quote form on this page. Include quantity, target package, delivery location, and required date in the request to obtain an accurate commercial response. Historical list prices do not reflect current market conditions and should not be used for budgeting a new production build.
What are the key specifications of ISL83483IB that engineers should know?
The key specifications are a 3 V to 3.6 V supply range, 250 kbps maximum data rate, half-duplex RS-485/RS-422 operation, and an 8-pin SOIC package. Renesas also identifies the implementation as 3.3 V BiCMOS with slew-rate-limited outputs. These parameters establish the basic electrical and packaging constraints, while exact current, temperature, common-mode, and receiver limits should be taken from the manufacturer datasheet.
How should the ISL83483IB differential bus be laid out?
Route the ISL83483IB differential pair as a short, continuous, impedance-controlled trace pair directly toward the connector or protection network. Keep the pair geometry consistent, avoid stubs, and place termination and surge-protection components near the line interface. Keep switching nodes, inductors, and high-current paths away from the receiver and connector area to minimize differential noise pickup and common-mode conversion.
Does ISL83483IB meet RoHS, REACH, and AEC-Q100 requirements?
The Renesas datasheet and product materials should be consulted for the definitive compliance declarations for the exact ordering code. The product is an industrial interface transceiver, but neither RoHS status, REACH status, nor AEC-Q100 qualification should be inferred solely from its function. Use the manufacturer material declaration or product compliance record before releasing a regulated or automotive production design.

Data referensi engineering untuk ISL83483IB — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the ISL83483IB for a 3.3 V half-duplex RS-485 or RS-422 link that operates at up to 250 kbps and benefits from controlled driver edges. It is a practical choice for industrial automation, building controls, instrumentation, and remote sensor nodes where lower EMI is valuable on long or imperfectly terminated cables. Select ISL83485 when the communication rate must be higher and the channel can manage the additional edge-rate energy. ISL83483IBZ-T can be considered when its exact ordering suffix and package format match the production BOM, but confirm the manufacturer pin assignment and ordering information before substitution. Neither alternative should be approved without checking supply range, common-mode limits, receiver thresholds, enable polarity, temperature range, and half-duplex timing against the original design.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini ISL83485 ISL83483IBZ-T
Brand Renesas Electronics Renesas Electronics Renesas Electronics
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC
Transceiver Function Single half-duplex RS-485/RS-422 transceiver Single half-duplex RS-485/RS-422 transceiver Single half-duplex RS-485/RS-422 transceiver
Supply Voltage 3 V to 3.6 V 3 V to 3.6 V 3 V to 3.6 V
Process Technology BiCMOS BiCMOS BiCMOS
Standards Support RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422

Diferensiator Kunci

  • Lower-speed slew-limited operation for reduced EMI (vsISL83485)
  • Exact interface ordering option with the same SOIC footprint (vsISL83483IBZ-T)

Catatan Desain

Route the differential bus as a matched, continuously referenced pair with symmetrical geometry and no unnecessary stubs. Keep the transceiver-to-connector path short, and place termination and surge-protection components close to the connector or protection boundary. If protection components have unequal parasitics, keep them within the transition region and preserve the pair’s impedance rather than separating the two conductors.

Separate the balanced bus from switching-regulator nodes, inductors, clock traces, and high-current return paths. Maintain a continuous ground reference under the differential pair, and connect the transceiver ground directly to the quiet signal-ground region rather than routing it through the logic return of a relay or actuator. This reduces differential noise pickup and limits conversion of common-mode switching energy into receiver errors.

Do not treat the half-duplex bus as a continuously transmitting RS-422 link. The ISL83483IB multiplexes its transmit and receive functions, so driver-enable control and turnaround timing must prevent two nodes from driving the bus simultaneously. Review the bus protocol, response delay, timeout, and fail-safe state, and ensure that a reset or fault condition cannot leave the driver enabled on a multidrop network.

The 250 kbps slew-rate-limited interface is intended to reduce edge-rate energy, reflections, and EMI, but it cannot compensate for an incorrect bus topology. Terminate the cable at the physical endpoints as appropriate, avoid unnecessary star branches, and verify common-mode voltage and noise margins along the full cable route. Add transient protection at externally accessible connectors while maintaining controlled differential impedance.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

Compliance declarations were not identified for the exact ordering code. AEC-Q100 is not applicable to the standard industrial ISL83483IB ordering option; verify all declarations against the manufacturer material-compliance record before production release.

Pencarian Terkait

ISL83483IB datasheet ISL83483IB datasheet pdf ISL83483IB pinout ISL83483IB equivalent ISL83483IB replacement ISL83483IB cross reference ISL83483IB vs ISL83485 ISL83483IB price ISL83483IB stock Renesas ISL83483IB ISL83483 3.3V transceiver ISL83483 250kbps RS485 ISL83483 SOIC-8 pinout ISL83483 industrial RS485 interface

Komponen dan Istilah Terkait

Renesas Electronics ISL83483IB ISL83485 ISL83483IBZ-T RS-485 RS-422 half-duplex transceiver differential line transceiver interface IC BiCMOS slew-rate-limited driver 3.3 V logic 250 kbps SOIC-8 surface mount industrial control factory automation building automation data acquisition remote sensing differential pair common-mode voltage EMI cable reflections
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ