ISL83483IB - 3.3V 250kbps RS-485/RS-422 Transceiver | Renesas
부품 번호: ISL83483IB ✓ 활성ISL83483IB 개요
An RS-485/RS-422 transceiver is an interface IC that converts between logic-level signals and balanced differential signals used for robust data transmission. RS-422 supports point-to-point, full-duplex links, while RS-485 commonly supports multidrop half-duplex buses. The ISL83483IB multiplexes its driver and receiver paths for half-duplex communication, making it useful where one pair of bus conductors serves both directions.
The principal feature of the ISL83483IB is its 250 kbps slew-rate-limited operation. Limiting the driver edge rate reduces high-frequency harmonics and associated EMI. The manufacturer also identifies the device as meeting both RS-485 and RS-422 requirements. Its 3 V to 3.6 V operating range accommodates regulated 3.3 V systems with the specified supply tolerance.
In half-duplex operation, the transceiver changes direction between transmission and reception. The receiver provides a logic-level output for the host controller, while the driver sends complementary differential voltage onto the bus. Because a single device must manage both functions, interface timing and bus direction control remain important parts of the surrounding firmware and circuitry.
Typical uses include industrial control links, factory automation equipment, building automation, instrumentation, and other balanced serial networks operating at modest data rates. The ISL83483IB is particularly suitable where low EMI is more important than maximum line rate, or where long cables and imperfect terminations can produce reflections.
The PCB layout should preserve the differential pair as a continuous, impedance-controlled route from the transceiver to the connector. Place termination, protection, and bus-surge components close to the line interface, while keeping switching regulators and high-current return paths away from the receiver input. Use the manufacturer pin-description and recommended-circuit guidance when assigning traces and selecting bypass capacitance.
This page combines the manufacturer interface description, package identification, operating limits, drop-in alternatives, and application guidance to support schematic capture, PCB design, sourcing, and lifecycle review of the ISL83483IB.
드롭인 대체품: ISL83483IB — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ISL83483IB (동일 폼 팩터 및 풋프린트) — 차이점: Package, Supply Voltage Range.
ISL83485IBZ-T
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →ISL83483IBZ-T
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ISL83483IB 사양
| Product Type | Half-duplex RS-485/RS-422 differential transceiver |
| Supply Voltage Range | 3 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| Maximum Data Rate | 250 kbps |
| Communication Mode | Half-duplex |
| Supported Standards | RS-485 and RS-422 |
| Driver Architecture | BiCMOS slew-rate-limited output |
| Transceiver Configuration | Single transmitter/receiver |
| 패키지 | 8-pin SOIC, 3.6 mm wide body |
| 실장 유형 | Surface mount |
ISL83483IB 8-pin soic, 3.6 mm wide body 핀 구성 가이드
ISL83483IB(8-pin soic, 3.6 mm wide body 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: ISL83483IB.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ISL83483IB 적합 용도: 6 애플리케이션s: Industrial PLC Serial Links, Factory Automation Equipment, Building Automation Networks, Instrumentation and Test Equipment, Data Acquisition Modules, Remote Sensor Networks.
Industrial PLC Serial Links
The ISL83483IB fits half-duplex communication between an industrial controller and remote I/O or field equipment operating at up to 250 kbps. Its 3 V to 3.6 V supply range suits regulated 3.3 V control electronics, while the slew-rate-limited BiCMOS driver reduces fast edge-rate energy and associated EMI. The transmitter and receiver share the bus in half-duplex mode, so the host controller must manage direction timing and turnaround without colliding with another transmitter. Cable length, topology, common-mode range, and termination should be checked against the manufacturer electrical limits before deployment.
추천
Factory Automation Equipment
The ISL83483IB supports balanced half-duplex links between factory sensors, actuators, and automation controllers where moderate data throughput and controlled emissions are important. Operation up to 250 kbps is sufficient for command, status, and configuration traffic, while the slew-rate-limited driver helps suppress reflections on cables with imperfect termination. A 3.3 V supply supports compact controller boards, and the 8-pin SOIC package simplifies routing on mixed-signal control hardware. Use surge protection at exposed cable entries and maintain the differential pair’s geometry through the protection network.
추천
Building Automation Networks
The ISL83483IB can bridge a 3.3 V controller to RS-485-compatible building automation equipment such as distributed sensors, HVAC interfaces, or access-control panels. Its 250 kbps limit accommodates supervisory control and status traffic, and the controlled output transition rate reduces EMI in panels containing switching power supplies and display electronics. The half-duplex arrangement conserves interface pins by sharing the differential bus for transmission and reception. Verify the selected bus topology, termination arrangement, and operating temperature against the manufacturer specifications before installation.
추천
Instrumentation and Test Equipment
The ISL83483IB is suitable for laboratory and process-instrumentation modules that exchange measurement commands and results over a balanced RS-485 or RS-422 link. Its 250 kbps slew-rate-limited operation reduces radiated emissions and ringing in compact instruments where long internal cable runs may be unavoidable. The 3.3 V operating range aligns with modern mixed-signal instrumentation, while half-duplex control simplifies bus sharing. Shielding, common-mode grounding, and transient protection remain important when the instrument connects to external equipment through user-accessible cables.
추천
Data Acquisition Modules
The ISL83483IB enables a distributed data-acquisition module to report samples, configuration, and diagnostics over a half-duplex RS-485 bus. A 250 kbps rate is appropriate for many sensor and monitor networks that prioritize deterministic communication and low EMI over maximum throughput. The transceiver operates from a 3 V to 3.6 V supply and fits an 8-pin SOIC footprint, making it practical for compact multi-channel boards. Care should be taken to isolate high-impedance sensors from the communication ground and to validate common-mode margins at the longest cable lengths.
추천
Remote Sensor Networks
The ISL83483IB suits remote sensor nodes that communicate over a shared RS-485 bus using 3.3 V logic. Its low data rate is sufficient for periodic environmental, position, or equipment measurements, and the slew-limited output helps control emissions in distributed cable installations. Because operation is half-duplex, the node must assert driver enable only when the bus is idle and must detect communication errors through its protocol or receiver status. External protection is advisable at the cable connector, and the differential route should remain symmetrical to avoid converting common-mode noise into receiver errors.
추천
추천 제품 요약
엔지니어링 참조 데이터: ISL83483IB — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ISL83485 | ISL83483IBZ-T |
|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Transceiver Function | Single half-duplex RS-485/RS-422 transceiver | Single half-duplex RS-485/RS-422 transceiver | Single half-duplex RS-485/RS-422 transceiver |
| Supply Voltage | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V |
| Process Technology | BiCMOS | BiCMOS | BiCMOS |
| Standards Support | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
주요 차별점
- Lower-speed slew-limited operation for reduced EMI (vs ISL83485)
- Exact interface ordering option with the same SOIC footprint (vs ISL83483IBZ-T)
설계 노트
Route the differential bus as a matched, continuously referenced pair with symmetrical geometry and no unnecessary stubs. Keep the transceiver-to-connector path short, and place termination and surge-protection components close to the connector or protection boundary. If protection components have unequal parasitics, keep them within the transition region and preserve the pair’s impedance rather than separating the two conductors.
Separate the balanced bus from switching-regulator nodes, inductors, clock traces, and high-current return paths. Maintain a continuous ground reference under the differential pair, and connect the transceiver ground directly to the quiet signal-ground region rather than routing it through the logic return of a relay or actuator. This reduces differential noise pickup and limits conversion of common-mode switching energy into receiver errors.
Do not treat the half-duplex bus as a continuously transmitting RS-422 link. The ISL83483IB multiplexes its transmit and receive functions, so driver-enable control and turnaround timing must prevent two nodes from driving the bus simultaneously. Review the bus protocol, response delay, timeout, and fail-safe state, and ensure that a reset or fault condition cannot leave the driver enabled on a multidrop network.
The 250 kbps slew-rate-limited interface is intended to reduce edge-rate energy, reflections, and EMI, but it cannot compensate for an incorrect bus topology. Terminate the cable at the physical endpoints as appropriate, avoid unnecessary star branches, and verify common-mode voltage and noise margins along the full cable route. Add transient protection at externally accessible connectors while maintaining controlled differential impedance.
규정 준수 정보
Compliance declarations were not identified for the exact ordering code. AEC-Q100 is not applicable to the standard industrial ISL83483IB ordering option; verify all declarations against the manufacturer material-compliance record before production release.