LM258DR2G - Dual 3-32V Op Amp | onsemi | Industrial
MPN: LM258DR2G ✓ AktifLM258DR2G Ringkasan
An operational amplifier is an analog signal-conditioning device that uses high open-loop gain to amplify the difference between two input voltages. The LM258 belongs to the general-purpose operational-amplifier family within the broader amplifier, analog IC, and semiconductor hierarchies. Its internally compensated architecture simplifies stable operation without an external compensation network, making it useful in industrial control, sensor conditioning, and general analog signal-processing systems.
Key characteristics include a low typical supply-current drain of 0.7 mA, typical input-offset voltage of 2 mV, typical input-offset current of 2 nA, and typical input-bias current of 15 nA. The common-mode range reaches the lower supply rail, which supports direct sensing of signals near ground in single-supply systems. A 32 V maximum differential input range matches the stated maximum supply capability.
The LM258's internally stabilized design provides approximately 0.6 V/µs slew rate and unity-gain stability, allowing it to function directly in voltage-follower, amplifier, comparator-style, and feedback-control circuits. Its 32 V operating capability supports higher supply rails than many low-voltage precision amplifiers, while the two-channel SOIC package reduces board area compared with discrete single amplifiers.
Typical uses include industrial sensor interfaces, low-side current measurement, control-loop amplifiers, audio preamplifier stages, and general-purpose signal conditioning. The device is especially appropriate when the circuit must tolerate a broad supply range, operate near the ground rail, and avoid external frequency-compensation components.
When designing around the LM258DR2G, account for input offset and bias currents when using high-impedance sensors. Place input and feedback components close to the package, maintain stable reference and feedback paths, and verify common-mode and output-swing limits against the actual supply voltage. This page combines electrical characteristics, package details, replacement options, and practical application guidance for faster engineering evaluation.
Alternatif penggantian untuk LM258DR2G — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian LM258DR2G (sama faktor bentuk dan footprint) — berbeda di dalam Package, Common-Mode Input Range, Gain-Bandwidth Product, Amplifier Type, Maximum Supply Voltage.
LM258D
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM258DT
✅ Drop-InKontak untuk harga
Lihat Datasheet →TSH22IDT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TSB7192IDT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LM2904PWR
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM324ADR
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM258DR2G Rating Maksimal & Karakteristik Listrik
| Number of Amplifier Channels | 2 channels |
| Supply Voltage Range | 3 V to 32 V |
| Slew Rate | 0.6 V/µs |
| Rentang Suhu Kerja | -25°C to +85°C |
| Typical Supply-Current Drain | 0.7 mA |
| Typical Input Offset Voltage | 2 mV |
| Typical Input Offset Current | 2 nA |
| Typical Input Bias Current | 15 nA |
| Differential Input Voltage Range | 32 V |
| Common-Mode Input Range | Extends to ground and VEE |
| Compensation | Internal frequency compensation |
| Supply Configuration | Single supply or split supply |
| Paket | 8-pin SOIC |
| Tipe Mounting | Surface mount |
| Product Classification | General-purpose operational amplifier |
| Status RoHS | ROHS3 compliant |
| REACH Status | Unaffected |
| Moisture Sensitivity Level | MSL 1 (unlimited) |
Konfigurasi Pin LM258DR2G
| Pin produk 1 | OUT1 — Output of amplifier 1 |
| Pin produk 2 | IN1− — Inverting input of amplifier 1 |
| Pin produk 3 | IN1+ — Non-inverting input of amplifier 1 |
| Pin produk 4 | GND — Ground connection |
| Pin produk 5 | IN2+ — Non-inverting input of amplifier 2 |
| Pin produk 6 | IN2− — Inverting input of amplifier 2 |
| Pin produk 7 | OUT2 — Output of amplifier 2 |
| Pin produk 8 | V+ — Positive supply voltage |
Aplikasi Umum
LM258DR2G cocok untuk 6 aplikasis: Industrial Sensor Signal Conditioning, Low-Side Current Measurement, Audio Preamplifier Stage, Motor Control Feedback, Test and Measurement Front End, Portable Battery-Powered Circuit.
Industrial Sensor Signal Conditioning
The LM258DR2G fits industrial sensor interfaces that operate from a 3 V to 32 V supply and require two analog channels in one 8-pin SOIC package. Its common-mode input range extends to ground, allowing signals near the lower rail to be conditioned without immediately saturating the input stage. The typical 0.6 V/µs slew rate supports moderate-bandwidth instrumentation, while the 0.7 mA typical supply-current drain limits quiescent demand in distributed monitoring systems. Engineers should still verify sensor source impedance, input-offset voltage, and the output swing required by the downstream converter or controller.
Direkomendasikan
Low-Side Current Measurement
LM258DR2G can amplify the small voltage produced by a low-side shunt when the system supply is too high for many precision low-voltage amplifiers. With a 3 V to 32 V operating range, it can sit behind a regulated front end and process a bipolar or near-ground shunt signal when the common-mode and differential-input limits are respected. The typical 2 mV input offset is significant on very small shunt drops, so gain and error budgets must account for it. The SOIC-8 package also keeps the two-amplifier implementation compact for gain stages and signal subtraction.
Direkomendasikan
Audio Preamplifier Stage
The dual LM258DR2G provides two independent amplifier channels for stereo audio preamplification, buffering, or active-filter functions. Its typical 0.6 V/µs slew rate is useful for moderate-bandwidth audio signals, and the broad 3 V to 32 V supply range supports split-supply and higher-rail legacy designs. Internal frequency compensation removes the need for an external compensation network in typical closed-loop configurations. Audio designers should avoid operating close to the output rails, check the required output swing, and assess noise and offset against the signal being amplified.
Direkomendasikan
Motor Control Feedback
LM258DR2G is appropriate for low-frequency current, position, or error-feedback amplification around industrial motor-control systems. Its 3 V to 32 V supply range supports operation from regulated low-voltage control rails and larger split supplies, while the common-mode input range extending to ground simplifies feedback sensing near the negative rail in some topologies. The internally compensated amplifier simplifies loop implementation, but designers must confirm unity-gain stability, output drive, and phase margin with the complete control network. Added filtering and grounding are especially important when the amplifier is placed near switching nodes.
Direkomendasikan
Test and Measurement Front End
LM258DR2G can implement input buffers, differential amplifiers, and gain stages in general-purpose test equipment. The 3 V to 32 V supply range provides flexibility across laboratory and industrial test voltages, while internal frequency compensation reduces the component count in closed-loop designs. With a typical slew rate of 0.6 V/µs, it is best suited to low- and intermediate-frequency signals rather than wideband instrumentation. Measurement accuracy still depends on input bias current, offset drift, resistor matching, and grounding. A precision instrumentation amplifier may be preferable when low offset and high input impedance dominate the design.
Direkomendasikan
Portable Battery-Powered Circuit
The LM258DR2G can support low-frequency signal conditioning in portable or battery-operated equipment when the available rail falls within its 3 V to 32 V operating range. Its typical 0.7 mA supply-current drain is modest for a dual amplifier, helping limit static consumption when both channels are active. Internal compensation supports simple voltage-follower and standard feedback networks without external compensation components. Designers should calculate the operating-point dissipation from the actual supply and load current, confirm that the amplifier remains in its linear region, and include shutdown behavior in the system-level power budget when battery life is critical.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk LM258DR2G — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | LM258D | LM258DT | TSH22IDT | TSB7192IDT | LM2904PWR | LM324ADR |
|---|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments |
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Amplifier Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 4 channels in the family |
Diferensiator Kunci
- Broad single- and split-supply operating range (vsLM2904PWR)
- Ground-referenced common-mode input capability (vsTSH22IDT)
- Internal compensation simplifies feedback design (vsTSB7192IDT)
- Low offset and bias-current figures for general-purpose designs (vsLM258DT)
Catatan Desain
Check the input common-mode range against the actual signal and supply voltage, not just the nominal output swing. The LM258 common-mode range extends to ground, but the output still requires headroom below the positive supply limit. In voltage-follower operation, leave adequate output margin for the intended load. For small shunt or sensor outputs, include the typical 2 mV input offset and 2 nA offset current in the error budget.
Route each input directly to its amplifier pin and keep feedback resistors and compensation-free gain networks close to the SOIC package. Place the ground return from pin 4 near the signal ground reference and maintain a continuous ground plane under the device. High-impedance input nodes should be minimized to reduce leakage and noise pickup. Keep switching-regulator power paths and inductors away from the input and feedback traces.
Estimated: with a 24 V supply and 0.7 mA typical quiescent current, static dissipation is approximately 16.8 mW, calculated as 24 V × 0.7 mA. Add output-current dissipation using the actual output voltage and current. The SOIC package is normally adequate for these low-power levels, but thermal performance depends on copper area, ambient temperature, and nearby heat sources. Confirm the maximum junction temperature from the manufacturer ratings.
LM258 is intended for general-purpose, low-to-moderate-bandwidth analog stages rather than high-speed signal conditioning. Use the 0.6 V/µs typical slew rate as a bandwidth and large-signal-response constraint. Add appropriate low-pass filtering when unwanted high-frequency noise or switch-node products are present. For precision current or sensor measurement, compare the offset, bias-current, and noise behavior against a dedicated instrumentation or current-sense amplifier.
Informasi Konformitas
The part is identified as ROHS3 compliant, REACH unaffected, and MSL 1 (unlimited). No separate lead-free, halogen-free, AEC-Q100, or conflict-minerals declaration was established for the exact MPN.