onsemi

LM258DR2G - Dual 3-32V Op Amp | onsemi | Industrial

料号: LM258DR2G ✓ 量产中
3 V to 32 V Vdss 0.7 mA Id 8-pin SOIC Package
最小起订量: 1 |

LM258DR2G 概述

The onsemi LM258DR2G is a dual, internally compensated general-purpose operational amplifier operating from 3 V to 32 V in an 8-pin SOIC package. It provides two amplifier channels, a typical slew rate of 0.6 V/µs, and an operating temperature range of -25°C to +85°C. The device is designed for single-supply or split-supply operation, with common-mode input voltage that extends to ground and to VEE.

An operational amplifier is an analog signal-conditioning device that uses high open-loop gain to amplify the difference between two input voltages. The LM258 belongs to the general-purpose operational-amplifier family within the broader amplifier, analog IC, and semiconductor hierarchies. Its internally compensated architecture simplifies stable operation without an external compensation network, making it useful in industrial control, sensor conditioning, and general analog signal-processing systems.

Key characteristics include a low typical supply-current drain of 0.7 mA, typical input-offset voltage of 2 mV, typical input-offset current of 2 nA, and typical input-bias current of 15 nA. The common-mode range reaches the lower supply rail, which supports direct sensing of signals near ground in single-supply systems. A 32 V maximum differential input range matches the stated maximum supply capability.

The LM258's internally stabilized design provides approximately 0.6 V/µs slew rate and unity-gain stability, allowing it to function directly in voltage-follower, amplifier, comparator-style, and feedback-control circuits. Its 32 V operating capability supports higher supply rails than many low-voltage precision amplifiers, while the two-channel SOIC package reduces board area compared with discrete single amplifiers.

Typical uses include industrial sensor interfaces, low-side current measurement, control-loop amplifiers, audio preamplifier stages, and general-purpose signal conditioning. The device is especially appropriate when the circuit must tolerate a broad supply range, operate near the ground rail, and avoid external frequency-compensation components.

When designing around the LM258DR2G, account for input offset and bias currents when using high-impedance sensors. Place input and feedback components close to the package, maintain stable reference and feedback paths, and verify common-mode and output-swing limits against the actual supply voltage. This page combines electrical characteristics, package details, replacement options, and practical application guidance for faster engineering evaluation.

直接替换替代料: LM258DR2G ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: LM258DR2G (相同外形与封装尺寸) ——差异在于 Package, Common-Mode Input Range, Gain-Bandwidth Product, Amplifier Type, Maximum Supply Voltage.

STMicroelectronics
Gain-Bandwidth Product: 700 kHz
Maximum Supply Voltage: 30 V
对比 LM258DR2G →
onsemi
Package: 8-SOIC (0.154 in, 3.90 mm width)
Common-Mode Input Range: Extending to ground/VEE
Gain-Bandwidth Product: 1 MHz
对比 LM258DR2G →
Texas Instruments
Package: 8-SOIC, 0.154 inch body width
Common-Mode Input Range: Includes ground
Gain-Bandwidth Product: 700 kHz
对比 LM258DR2G →
onsemi
Common-Mode Input Range: Extends to ground or VEE
Gain-Bandwidth Product: 700 kHz
Amplifier Type: Dual general-purpose operational amplifier
对比 LM258DR2G →
STMicroelectronics
Amplifier Type: Dual low-power operational amplifier
对比 LM258DR2G →
Texas Instruments
Package: 8-TSSOP, 4.40 mm width
Common-Mode Input Range: Includes ground
Gain-Bandwidth Product: 700 kHz
对比 LM258DR2G →
Texas Instruments
Package: 14-pin SOIC (D)
Gain-Bandwidth Product: 1.2 MHz
Maximum Supply Voltage: 30 V
对比 LM258DR2G →

LM258D

✅ 直接替换
STMicroelectronics
📦 SOIC-8
2 circuits · Two independent, internally frequency-compensated operational amplifiers · 30 V · 700 kHz · Single supply or split supply · Extends toward ground and VEE · Low-power class · Standard general-purpose amplifier

联系询价

查看数据手册 →

LM258DT

✅ 直接替换
STMicroelectronics
📦 SOIC-8
Dual low-power operational amplifier · 2 amplifiers · 2 circuits · 3 V to 30 V · 1.1 MHz · 0.6 V/us · 100 dB · 500 uA

联系询价

查看数据手册 →

TSH22IDT

✅ 直接替换
📦 SOIC-8
Same-package, pin-compatible dual amplifier with rail-to-rail input characteristics; input common-mode behavior differs from the ground-referenced LM258DR2G.

📋 参考替代料(不在目录中)

TSB7192IDT

✅ 直接替换
📦 SOIC-8
Same-package dual amplifier offering different rail-to-rail and low-power characteristics; verify the supply range, slew rate, and output capability against the design.

📋 参考替代料(不在目录中)

LM2904PWR

✅ 直接替换
Texas Instruments
📦 SOIC-8
2 circuits · Dual general-purpose operational amplifier · 26 V · 700 kHz · 0.7 mA · Independent of supply voltage · Single supply or split supply · Includes ground

联系询价

查看数据手册 →

LM324ADR

✅ 直接替换
Texas Instruments
📦 SOIC-8
4 circuits · 30 V · 1.2 MHz · 3 mV · Single supply or split supply · Internally compensated · True differential inputs · 14 pins

联系询价

查看数据手册 →

LM258DR2G 最大额定值与电气特性

Number of Amplifier Channels 2 channels
Supply Voltage Range 3 V to 32 V
Slew Rate 0.6 V/µs
工作温度范围 -25°C to +85°C
Typical Supply-Current Drain 0.7 mA
Typical Input Offset Voltage 2 mV
Typical Input Offset Current 2 nA
Typical Input Bias Current 15 nA
Differential Input Voltage Range 32 V
Common-Mode Input Range Extends to ground and VEE
Compensation Internal frequency compensation
Supply Configuration Single supply or split supply
封装 8-pin SOIC
安装类型 Surface mount
Product Classification General-purpose operational amplifier
RoHS 状态 ROHS3 compliant
REACH Status Unaffected
Moisture Sensitivity Level MSL 1 (unlimited)

LM258DR2G 引脚配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
引脚 1 OUT1 — Output of amplifier 1
引脚 2 IN1− — Inverting input of amplifier 1
引脚 3 IN1+ — Non-inverting input of amplifier 1
引脚 4 GND — Ground connection
引脚 5 IN2+ — Non-inverting input of amplifier 2
引脚 6 IN2− — Inverting input of amplifier 2
引脚 7 OUT2 — Output of amplifier 2
引脚 8 V+ — Positive supply voltage

典型应用

LM258DR2G 适用于 6 应用s: Industrial Sensor Signal Conditioning, Low-Side Current Measurement, Audio Preamplifier Stage, Motor Control Feedback, Test and Measurement Front End, Portable Battery-Powered Circuit.

🏭

Industrial Sensor Signal Conditioning

The LM258DR2G fits industrial sensor interfaces that operate from a 3 V to 32 V supply and require two analog channels in one 8-pin SOIC package. Its common-mode input range extends to ground, allowing signals near the lower rail to be conditioned without immediately saturating the input stage. The typical 0.6 V/µs slew rate supports moderate-bandwidth instrumentation, while the 0.7 mA typical supply-current drain limits quiescent demand in distributed monitoring systems. Engineers should still verify sensor source impedance, input-offset voltage, and the output swing required by the downstream converter or controller.

⚡

Low-Side Current Measurement

LM258DR2G can amplify the small voltage produced by a low-side shunt when the system supply is too high for many precision low-voltage amplifiers. With a 3 V to 32 V operating range, it can sit behind a regulated front end and process a bipolar or near-ground shunt signal when the common-mode and differential-input limits are respected. The typical 2 mV input offset is significant on very small shunt drops, so gain and error budgets must account for it. The SOIC-8 package also keeps the two-amplifier implementation compact for gain stages and signal subtraction.

🎧

Audio Preamplifier Stage

The dual LM258DR2G provides two independent amplifier channels for stereo audio preamplification, buffering, or active-filter functions. Its typical 0.6 V/µs slew rate is useful for moderate-bandwidth audio signals, and the broad 3 V to 32 V supply range supports split-supply and higher-rail legacy designs. Internal frequency compensation removes the need for an external compensation network in typical closed-loop configurations. Audio designers should avoid operating close to the output rails, check the required output swing, and assess noise and offset against the signal being amplified.

🏭

Motor Control Feedback

LM258DR2G is appropriate for low-frequency current, position, or error-feedback amplification around industrial motor-control systems. Its 3 V to 32 V supply range supports operation from regulated low-voltage control rails and larger split supplies, while the common-mode input range extending to ground simplifies feedback sensing near the negative rail in some topologies. The internally compensated amplifier simplifies loop implementation, but designers must confirm unity-gain stability, output drive, and phase margin with the complete control network. Added filtering and grounding are especially important when the amplifier is placed near switching nodes.

🔧

Test and Measurement Front End

LM258DR2G can implement input buffers, differential amplifiers, and gain stages in general-purpose test equipment. The 3 V to 32 V supply range provides flexibility across laboratory and industrial test voltages, while internal frequency compensation reduces the component count in closed-loop designs. With a typical slew rate of 0.6 V/µs, it is best suited to low- and intermediate-frequency signals rather than wideband instrumentation. Measurement accuracy still depends on input bias current, offset drift, resistor matching, and grounding. A precision instrumentation amplifier may be preferable when low offset and high input impedance dominate the design.

📱

Portable Battery-Powered Circuit

The LM258DR2G can support low-frequency signal conditioning in portable or battery-operated equipment when the available rail falls within its 3 V to 32 V operating range. Its typical 0.7 mA supply-current drain is modest for a dual amplifier, helping limit static consumption when both channels are active. Internal compensation supports simple voltage-follower and standard feedback networks without external compensation components. Designers should calculate the operating-point dissipation from the actual supply and load current, confirm that the amplifier remains in its linear region, and include shutdown behavior in the system-level power budget when battery life is critical.

What is the operating voltage of LM258DR2G?
The LM258DR2G operates from 3 V to 32 V as a dual operational amplifier. According to the onsemi datasheet, it supports single-supply or split-supply configurations, allowing the same device to serve low-voltage and higher-voltage analog circuits. Designers should verify that the complete signal path remains inside the common-mode and output-swing limits at the selected supply voltage.
What are the key specifications of LM258DR2G that engineers should know?
The LM258DR2G is a dual, internally compensated general-purpose operational amplifier rated for 3 V to 32 V operation. According to the onsemi datasheet, it provides a typical slew rate of 0.6 V/µs, 0.7 mA typical supply-current drain, 2 mV typical input-offset voltage, and an operating range of -25°C to +85°C. It is supplied in an 8-pin SOIC package.
Where can I download the LM258DR2G datasheet PDF?
The LM258DR2G datasheet is available through the onsemi document listing linked on this page. The manufacturer document describes the dual amplifier, electrical characteristics, limiting conditions, pin assignments, and application information. Use the onsemi datasheet for final supply limits, input-current behavior, compensation assumptions, and soldering or handling requirements.
Where can I find the LM258DR2G pinout?
The LM258DR2G uses the standard 8-pin dual-operational-amplifier SOIC arrangement: pin 1 is OUT1, pins 2 and 3 are IN1− and IN1+, pin 4 is GND, pins 5 and 6 are IN2+ and IN2−, pin 7 is OUT2, and pin 8 is V+. Confirm the package drawing and pin numbering in the onsemi datasheet before assigning PCB tracks.
Is LM258DR2G suitable for single-supply sensor conditioning?
Yes, LM258DR2G is suitable for single-supply sensor conditioning because its common-mode input range extends to ground and the lower supply rail. According to the onsemi datasheet, the device also accepts split-supply operation. The common-mode range makes the amplifier useful for sensors whose output lies close to 0 V, although output-swing headroom must be checked at the selected supply.
What is the difference between LM258DR2G and LM258DT?
LM258DR2G and LM258DT are dual general-purpose operational amplifiers in 8-pin SOIC packages, but they are offered by different manufacturers. The onsemi LM258DR2G is specified for 3 V to 32 V and -25°C to +85°C. The STMicroelectronics LM258DT provides a pin-compatible alternative function, but its electrical limits and qualification details should be checked before substitution.
When should I choose LM258DR2G over LM2904PWR?
Choose LM258DR2G when the design needs a dual amplifier with a 3 V to 32 V supply range and typical 0.6 V/µs slew rate. Choose LM2904PWR when its lower quiescent current or other manufacturer-specific ratings better match the design. Both use a conventional 8-pin dual-op-amp footprint, but input bias, offset, noise, and stability behavior should be compared.
What is the best drop-in replacement for LM258DR2G?
The best drop-in replacement is the one that preserves the 8-pin SOIC footprint, pin functions, supply range, and required stability margin. LM258DT is a leading cross-brand option because it implements the same dual general-purpose amplifier arrangement. Confirm electrical details for the exact replacement, especially input bias current, output swing, slew rate, and operating-temperature limits, before approving it for production.
Can TSH22IDT replace LM258DR2G?
TSH22IDT can serve as a pin-compatible 8-pin dual-op-amp replacement when its electrical characteristics satisfy the circuit. The cross-reference information identifies same-package, pin-compatible alternatives, but the onsemi LM258DR2G remains the reference for a 3 V to 32 V supply, 0.6 V/µs typical slew rate, and ground-referenced common-mode operation. Validate stability, offset, bias current, and output drive before substitution.
Where to buy LM258DR2G online?
Use the Request a Quote form on this page to request LM258DR2G availability, order quantities, and current lead time. The form routes the request without relying on a static listing that may become outdated. Provide the required package suffix and quantity so the quote can be matched to the correct 8-pin SOIC configuration.
What is the price of LM258DR2G?
Current LM258DR2G commercial terms are available through the Request a Quote form on this page. The form should be used instead of a static price figure because component pricing, quantity, and sourcing conditions can change. Submit the required quantity, packaging preference, and delivery location to obtain a current quotation for the exact MPN.
What is the lead time and stock status for LM258DR2G?
LM258DR2G stock and lead time should be confirmed through the Request a Quote form on this page. Submit the required quantity, target delivery date, and shipment location. This avoids treating a distributor-page availability message as a guaranteed allocation and enables the request to be matched to current supply conditions.
Is LM258DR2G in stock?
LM258DR2G availability is confirmed on demand through the Request a Quote form on this page. Provide the required order quantity and delivery terms to receive a current availability response. For production planning, include the target date because available quantity and lead time may vary with order size and packaging requirements.
How much power does LM258DR2G dissipate?
Estimated: at a 24 V supply and 0.7 mA typical supply-current drain, LM258DR2G dissipates about 16.8 mW under the no-load condition, calculated as 24 V × 0.7 mA. Actual dissipation increases with output current and depends on common-mode and output operating points. Use the measured current and supply voltage for a board-specific thermal estimate.
Is LM258DR2G RoHS and REACH compliant?
LM258DR2G is identified as ROHS3 compliant and REACH unaffected, with MSL 1, unlimited floor-life status. These classifications support its use in RoHS-oriented designs and indicate that moisture sensitivity does not impose a finite floor-life restriction. Buyers handling regulated products should request current declarations for the exact lot and shipment.

工程参考数据: LM258DR2G ——对比、设计指导和合规信息。

选型指南

Choose LM258DR2G when the design needs two general-purpose amplifier channels, operation from 3 V to 32 V, internal compensation, and a common-mode input range that reaches ground. It is well suited to industrial sensor conditioning, low-side measurement, audio preamplification, and moderate-bandwidth feedback loops. Choose LM258DT when a cross-brand dual general-purpose amplifier with the same SOIC-8 arrangement is preferred, after checking its electrical limits. Choose TSH22IDT or TSB7192IDT when rail-to-rail input behavior or their low-power characteristics are more valuable than the LM258's conventional high-voltage general-purpose profile. Choose LM2904PWR for lower quiescent demand in battery-powered circuitry, or LM324ADR when a lower-cost general-purpose amplifier family is acceptable. Validate offset, input bias current, noise, output swing, stability, and temperature range for every substitution.

与替代料对比

参数 本产品 LM258D LM258DT TSH22IDT TSB7192IDT LM2904PWR LM324ADR
Brand onsemi onsemi STMicroelectronics STMicroelectronics STMicroelectronics Texas Instruments Texas Instruments
Package SOIC-8 SOIC-8 SOIC-8 SOIC-8 SOIC-8 SOIC-8 SOIC-8
Amplifier Channels 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels 4 channels in the family

关键差异点

  • Broad single- and split-supply operating range (对比 LM2904PWR)
  • Ground-referenced common-mode input capability (对比 TSH22IDT)
  • Internal compensation simplifies feedback design (对比 TSB7192IDT)
  • Low offset and bias-current figures for general-purpose designs (对比 LM258DT)

设计说明

Check the input common-mode range against the actual signal and supply voltage, not just the nominal output swing. The LM258 common-mode range extends to ground, but the output still requires headroom below the positive supply limit. In voltage-follower operation, leave adequate output margin for the intended load. For small shunt or sensor outputs, include the typical 2 mV input offset and 2 nA offset current in the error budget.

Route each input directly to its amplifier pin and keep feedback resistors and compensation-free gain networks close to the SOIC package. Place the ground return from pin 4 near the signal ground reference and maintain a continuous ground plane under the device. High-impedance input nodes should be minimized to reduce leakage and noise pickup. Keep switching-regulator power paths and inductors away from the input and feedback traces.

Estimated: with a 24 V supply and 0.7 mA typical quiescent current, static dissipation is approximately 16.8 mW, calculated as 24 V × 0.7 mA. Add output-current dissipation using the actual output voltage and current. The SOIC package is normally adequate for these low-power levels, but thermal performance depends on copper area, ambient temperature, and nearby heat sources. Confirm the maximum junction temperature from the manufacturer ratings.

LM258 is intended for general-purpose, low-to-moderate-bandwidth analog stages rather than high-speed signal conditioning. Use the 0.6 V/µs typical slew rate as a bandwidth and large-signal-response constraint. Add appropriate low-pass filtering when unwanted high-frequency noise or switch-node products are present. For precision current or sensor measurement, compare the offset, bias-current, and noise behavior against a dedicated instrumentation or current-sense amplifier.

合规信息

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The part is identified as ROHS3 compliant, REACH unaffected, and MSL 1 (unlimited). No separate lead-free, halogen-free, AEC-Q100, or conflict-minerals declaration was established for the exact MPN.

相关搜索

LM258DR2G LM258DR2G datasheet LM258DR2G datasheet pdf LM258DR2G pinout LM258DR2G specifications onsemi LM258DR2G LM258DR2G SOIC-8 amplifier LM258DR2G 3-32V LM258DR2G equivalent LM258DR2G replacement LM258DR2G vs LM258DT LM258DR2G price LM258DR2G stock LM258DR2G application circuit

相关元器件 & 术语

onsemi LM258DR2G LM258D LM258DT TSH22IDT TSB7192IDT Texas Instruments LM2904PWR LM324ADR operational amplifier general-purpose operational amplifier dual amplifier analog IC semiconductor single-supply operation split-supply operation input offset voltage input bias current common-mode input voltage range slew rate internal frequency compensation SOIC-8 surface-mount package RoHS REACH
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情