onsemi

LM2903VDG - Dual 2-36V Open-Collector Comparator | onsemi

MPN: LM2903VDG ✓ Aktif
2 V to 36 V Vdss 0.5 µA Id 8-pin SOIC Package
MOQ: 1 |

LM2903VDG Ringkasan

The onsemi LM2903VDG is a dual differential voltage comparator designed for single or split-supply operation over a 2 V to 36 V supply range. Each half of the device provides an open-collector output, rail-to-rail input capability, and independent input and output pins. The component is offered in an 8-pin SOIC package for surface-mount industrial, automotive, and consumer electronic assemblies.

A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital-level indication of their relationship. The LM2903 series belongs to the comparator hierarchy, which also includes the broader category of analog interface ICs. Its two independent channels allow one package to implement two comparison functions while avoiding the common-mode limitations associated with older single-supply comparators.

The principal features of the LM2903VDG include two independent precision comparator channels, open-collector outputs suitable for pulling a logic node low, operation from a single 2 V supply or split supplies, and an extended temperature range of -40 °C to 125 °C. Maximum input offset voltage is 15 mV, maximum average input bias current is 0.5 µA, and typical response time is 1.5 µs. The open-collector architecture requires an external pull-up resistor when driving CMOS or other logic families.

Each channel contains non-inverting and inverting inputs, an output, and a common power-supply connection. The two channels operate independently, but both share the same package pins for ground and positive supply. Because the outputs are open collectors, they can remain in a high-impedance state until an external pull-up establishes the logic-high voltage. This feature also permits several open-collector outputs to share a bus when the application requires wired logic behavior.

Typical uses include automotive sensing interfaces, industrial control and monitoring circuits, battery-powered equipment, consumer electronics, and general-purpose threshold detection. A common example is comparing a divided sensor signal with a reference voltage, where the comparator output indicates whether the measured value is above or below the selected threshold. The 2 V minimum supply permits operation from low-voltage rails, while the 36 V maximum supports applications with higher industrial supply levels.

Designers should account for the open-collector output when selecting the pull-up resistor and logic family. The resistor must be small enough to achieve the required output rise time but large enough to limit pull-up current when the transistor is saturated. Input-referred offset and bias-current errors should also be included when the comparator threshold requires high accuracy.

This product page combines the exact LM2903VDG ordering information with technical characteristics, verified source links, application guidance, and same-footprint replacement analysis. It is structured to help engineers identify suitability, evaluate alternatives, and plan PCB implementation without overlooking the electrical distinctions that matter in comparator designs.

Alternatif penggantian untuk LM2903VDG — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian LM2903VDG (sama faktor bentuk dan footprint) — berbeda di dalam Package, Comparator Type, Mounting Type, Output Type, Number of Channels.

Texas Instruments
Package: 8-pin SOIC (D)
Comparator Type: Dual differential comparator
Output Type: Open-collector
Bandingkan dengan LM2903VDG →
Texas Instruments
Package: 8-pin SOIC, 0.154 inch (3.90 mm) width
Comparator Type: Dual differential comparator
Output Type: Open-collector
Bandingkan dengan LM2903VDG →
onsemi
Package: 8-pin PDIP
Comparator Type: Dual general-purpose voltage comparator
Mounting Type: Through-hole
Bandingkan dengan LM2903VDG →

LM2903DG4

✅ Drop-In
Texas Instruments
📦 8-SOIC
Dual differential comparator · 2 channels · Single or dual supply · 32 V · 30 V · 0.4 mA typical per comparator · Open-collector · TTL, MOS, and CMOS compatible

Kontak untuk harga

Lihat Datasheet →

LM2903VN

✅ Drop-In
onsemi
📦 8-SOIC
Dual general-purpose voltage comparator · 2 · 2 V to 36 V · Rail-to-rail · Open-collector · 8-pin PDIP · Through-hole · -40°C to +125°C

Kontak untuk harga

Lihat Datasheet →

LM2903BIDR

✅ Drop-In
Texas Instruments
📦 8-SOIC
Dual differential comparator · 2 channels · Open-collector · 36 V · 2 V · 0.37 mV · 3.5 nA · 200 µA per comparator

Kontak untuk harga

Lihat Datasheet →

LM2903VN

✅ Drop-In
onsemi
📦 8-SOIC
Dual general-purpose voltage comparator · 2 · 2 V to 36 V · Rail-to-rail · Open-collector · 8-pin PDIP · Through-hole · -40°C to +125°C

Kontak untuk harga

Lihat Datasheet →

LM2903BIDR

✅ Drop-In
Texas Instruments
📦 8-SOIC
Dual differential comparator · 2 channels · Open-collector · 36 V · 2 V · 0.37 mV · 3.5 nA · 200 µA per comparator

Kontak untuk harga

Lihat Datasheet →

LM2903VDG Rating Maksimal & Karakteristik Listrik

Comparator Type Dual differential voltage comparator
Number of Channels 2 independent channels
Supply Voltage Range 2 V to 36 V
Supply Configuration Single or split supply
Tipe Output Open collector
Input Common-Mode Range Rail-to-rail
Maximum Input Offset Voltage 15 mV
Maximum Average Input Bias Current 0.5 µA
Typical Response Time 1.5 µs
Rentang Suhu Kerja -40 °C to 125 °C
Paket 8-pin SOIC
Tipe Mounting Surface mount
Output Compatibility TTL and CMOS

Konfigurasi Pin LM2903VDG

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin produk 1 OUT 1 — Open-collector output of comparator channel 1
Pin produk 2 IN− 1 — Inverting input of comparator channel 1
Pin produk 3 IN+ 1 — Non-inverting input of comparator channel 1
Pin produk 4 GND — Ground connection
Pin produk 5 IN+ 2 — Non-inverting input of comparator channel 2
Pin produk 6 IN− 2 — Inverting input of comparator channel 2
Pin produk 7 OUT 2 — Open-collector output of comparator channel 2
Pin produk 8 VCC — Positive supply connection

Aplikasi Umum

LM2903VDG cocok untuk 6 aplikasis: Automotive Sensor Threshold Detection, Industrial Control and Monitoring, Battery-Powered Equipment, Consumer Electronics Control, Power Rail Supervision, Open-Collector Logic Interface.

🚗

Automotive Sensor Threshold Detection

The LM2903VDG fits automotive sensing circuits that compare a divided sensor voltage against a reference. Its two independent channels can monitor two conditions, such as an overvoltage threshold and an undervoltage threshold, while the extended -40 °C to 125 °C range supports harsh ambient conditions. Each channel responds in 1.5 µs typical time and has 15 mV maximum input offset voltage, so the system should budget that error in its threshold design. The open-collector output can directly pull a low-power diagnostic or logic input low, with an external pull-up setting the high voltage. Verify the exact automotive qualification and grade-specific limits in the manufacturer documentation before production use.

🏭

Industrial Control and Monitoring

The LM2903VDG is suitable for industrial control boards that must make a binary decision about an analog process or power signal. Place one channel on the non-inverting input and the other on the inverting input when independent upper and lower limits are required. Its 2 V to 36 V operating range accommodates low-voltage logic rails and higher-voltage monitoring interfaces, while the rail-to-rail input characteristic helps maximize usable signal range. The 1.5 µs typical response time supports relatively quick threshold actions. Because the outputs are open collector, use pull-up resistors matched to the receiving controller and account for the maximum output offset when setting safety or control limits.

⚡

Battery-Powered Equipment

The LM2903VDG can monitor a battery-derived system using its low 2 V minimum supply and 0.5 µA maximum average input bias current. Two independent channels may supervise a battery threshold and another system rail without using two comparator packages. The open-collector output allows a pulled-up status signal to remain in a high-impedance state when the comparator is inactive, helping reduce unnecessary load in a power-sensitive design. The rail-to-rail input capability is valuable when the monitored voltage approaches the available supply rail. Select the pull-up value to balance leakage-driven static current against the required logic rise time, and check the complete operating-temperature and supply-current limits in the device datasheet.

📱

Consumer Electronics Control

The LM2903VDG provides economical dual-channel logic for consumer products that must convert an analog level into a switching decision. Examples include charger-state detection, display threshold control, or protection of an analog front end. Its 8-pin SOIC package supports compact surface-mount layouts, and the two channels reduce the number of packages needed when two thresholds must be evaluated. The 15 mV maximum input offset and 1.5 µs typical response time are important when defining the point at which the product changes state. An external pull-up is required for each open-collector output; keep that connection short and choose its resistance according to the input capacitance and required rise time.

🔧

Power Rail Supervision

The LM2903VDG can supervise power rails by comparing divided supply voltages with reference levels. Its two independent channels allow a single package to detect both an undervoltage and an overvoltage condition, and the rail-to-rail input range is useful in low-supply systems where the signal of interest occupies much of the available range. The device operates from 2 V to 36 V, providing flexibility across consumer, industrial, and automotive-style systems. Its open-collector outputs can drive an enable, reset, or fault input when paired with appropriate pull-ups. The 15 mV maximum offset must be included in the threshold-error budget, while the 1.5 µs typical response time determines how quickly the supervision circuit reacts.

🧩

Open-Collector Logic Interface

The LM2903VDG is appropriate when a comparator must interface with TTL, CMOS, or another open-collector-compatible logic node. The output transistor pulls the node toward ground, while an external resistor establishes the high state at the receiver's supply voltage. This arrangement offers flexibility in system partitioning because the pull-up can be tied to a local or protected rail rather than the comparator supply. Both channels are independent, permitting separate logic decisions without contention. The 2 V to 36 V supply range and 1.5 µs typical response time support many control and monitoring functions. Size the pull-up for the total input capacitance and required rise time, while confirming that the output current and saturation limits meet the worst-case load requirement.

Ringkasan Produk Direkomendasikan

LM2903VDG onsemi Digunakan di dalam: Automotive Sensor Threshold Detection, Industrial Control and Monitoring, Battery-Powered Equipment, Consumer Electronics Control, Power Rail Supervision, Open-Collector Logic Interface LM2903DG onsemi Digunakan di dalam: Automotive Sensor Threshold Detection, Consumer Electronics Control LM2903 Pin-compatible dual comparator Digunakan di dalam: Industrial Control and Monitoring, Open-Collector Logic Interface LM2903V LM2903-family comparator option Digunakan di dalam: Battery-Powered Equipment LM2903B LM2903-family drop-in candidate Digunakan di dalam: Power Rail Supervision
What is the LM2903VDG?
The LM2903VDG is an onsemi dual differential voltage comparator with two independent channels, open-collector outputs, and rail-to-rail input capability. According to the onsemi LM2903 family information, it operates from 2 V to 36 V in single- or split-supply configurations and is packaged in an 8-pin SOIC. It is intended for general-purpose threshold detection in consumer, automotive, and industrial electronics.
What is the supply voltage range of LM2903VDG?
The LM2903VDG operates from 2 V to 36 V. The onsemi family description identifies operation using either one supply or split supplies, while the comparator input range can extend from the negative supply to a level near the positive rail. This makes the device suitable for low-voltage logic systems and higher-voltage industrial sensing interfaces when the output is pulled up to an appropriate logic voltage.
Where can I download the LM2903VDG datasheet?
The LM2903VDG datasheet is available through the official onsemi LM2903 product page at https://www.onsemi.com/products/standard-products/amplifiers-comparators/comparators/lm2903. The part is also indexed through Octopart and appears in the LM2903 datasheet listings. Use the manufacturer PDF for final pin assignments, electrical limits, ordering information, and recommended application circuits.
What is the LM2903VDG pinout?
The 8-pin SOIC pinout assigns OUT 1 to pin 1, IN− to pin 2, IN+ to pin 3, GND to pin 4, IN+ to pin 5, IN− to pin 6, OUT 2 to pin 7, and VCC to pin 8. These assignments follow the standard dual-comparator pinout used by the LM2903 series. Use the manufacturer pin-description table when assigning PCB tracks and pull-up components.
Does LM2903VDG need an output pull-up resistor?
Yes, the LM2903VDG open-collector outputs require an external pull-up resistor to establish a logic-high voltage. The resistor connects each output to the supply used by the receiving logic circuit and limits current when the output transistor pulls the node low. According to the onsemi LM2903 family description, the outputs are compatible with TTL and CMOS logic.
What are the key specifications of LM2903VDG that engineers should know?
The LM2903VDG provides two independent comparator channels over a 2 V to 36 V supply range, with rail-to-rail inputs, open-collector outputs, 15 mV maximum input offset voltage, 0.5 µA maximum average input bias current, and 1.5 µs typical response time. The onsemi LM2903 family information also confirms its -40 °C to 125 °C operating-temperature range and 8-pin SOIC implementation.
Is LM2903VDG suitable for automotive applications?
The LM2903VDG is marketed for automotive and industrial applications and has an extended -40 °C to 125 °C operating range. However, the exact AEC-Q100 qualification status is not stated in the retrieved product information. Confirm that qualification in the manufacturer datasheet or quality documentation before assigning the device to a safety- or reliability-critical automotive design.
LM2903VDG vs LM2903DG - which is the better replacement?
LM2903VDG and LM2903DG are both onsemi 8-pin SOIC dual open-collector comparators in the LM2903 family, so their board footprint and basic supply capability align. Choose the version whose temperature-grade and automotive qualification requirements match the application after reviewing the manufacturer ordering information. Do not infer AEC-Q100 status from the suffix alone without checking the applicable datasheet.
LM2903VDG vs TI LM2903 - which is better for an industrial design?
The TI LM2903 is described as a dual differential comparator with pin-for-pin drop-in compatibility, making it a candidate for existing LM2903VDG layouts. Selection should consider the exact onsemi and TI electrical limits, supply behavior, output ratings, temperature grade, and qualification documents. Both families share the general dual-comparator function, but the final choice must follow the device-specific datasheets.
When should I choose LM2903VDG over a pin-compatible alternative?
Choose LM2903VDG when the design benefits from the onsemi LM2903 family's extended -40 °C to 125 °C range, open-collector output, and 2 V to 36 V operating capability. Consider a drop-in alternative when it provides a needed automotive qualification, tighter offset specification, or another verified electrical improvement without changing the 8-pin SOIC footprint. Otherwise, retaining LM2903VDG can minimize schematic and PCB changes.
What can replace LM2903VDG?
A valid replacement must be a dual comparator in an 8-pin SOIC with compatible input, output, supply, and ground pin assignments. LM2903DG from onsemi and the TI LM2903 and LM2903V families are direct candidates for review because their documentation identifies the same dual-comparator form and pin compatibility. Confirm operating limits and qualification requirements before using any candidate as a production substitute.
What is the best cross-brand equivalent for LM2903VDG?
The TI LM2903 is the clearest cross-brand candidate because its manufacturer page identifies pin-for-pin drop-in compatibility with upgraded functionality. It remains in the 8-pin SOIC comparator family and is intended for the same dual-comparator use cases. Verify voltage limits, input offset, response time, output-current capability, and temperature grade against the LM2903VDG datasheet before release.
Where can I buy LM2903VDG online?
Use the Request a Quote form on this page to request LM2903VDG availability, current lead time, and commercial terms. The form keeps the inquiry associated with the exact onsemi LM2903VDG 8-pin SOIC ordering code. Stock status can change quickly, so confirm quantity, packaging, and delivery requirements when submitting the request.
What is the price of LM2903VDG?
Current commercial pricing for the exact LM2903VDG is obtained through the Request a Quote form on this page. The form supports an inquiry for the onsemi 8-pin SOIC dual comparator and its required quantity. Pricing depends on order quantity, delivery terms, and market availability, so request a quotation rather than relying on a stale historical listing.
What is the lead time and stock status for LM2903VDG?
The current lead time and stock position for LM2903VDG should be requested through the Request a Quote form on this page. Include the required order quantity, target shipment date, and acceptable packaging so the manufacturer or authorized supply channel can confirm the appropriate schedule. The onsemi LM2903 family remains presented as an active product family.

Data referensi engineering untuk LM2903VDG — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the LM2903VDG when the design requires two independent open-collector comparison channels, a 2 V to 36 V operating range, and an extended -40 °C to 125 °C temperature specification in an 8-pin SOIC package. LM2903DG is a closely related onsemi option when its suffix-specific grade better matches the design. TI LM2903 is appropriate when its manufacturer-documented pin-for-pin upgrade is preferred, while TI LM2903V and LM2903B are candidates where revised or version-specific comparator specifications are advantageous. For every alternative, verify the exact input common-mode limits, output current, offset voltage, response time, qualification status, and lifecycle requirements. The open-collector outputs also require external pull-up resistors in every replacement scenario, so a valid substitution must preserve both the physical footprint and the surrounding resistor network.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini LM2903DG LM2903V LM2903 LM2903V LM2903B
Brand onsemi onsemi onsemi Texas Instruments Texas Instruments Texas Instruments
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Comparator Channels 2 independent channels 2 independent channels 2 independent channels 2 channels 2 channels 2 channels
Output Type Open collector Open collector Open collector Open collector Open collector Open collector

Diferensiator Kunci

  • Wide operating range for low- and high-voltage monitoring (vsLM2903DG)
  • Two independent channels in a compact SOIC footprint (vsLM2903B)
  • Open-collector outputs support flexible logic interfacing (vsLM2903)

Catatan Desain

Do not connect a logic load directly to an open-collector output without a pull-up resistor. Add one resistor from each output to the supply used by the receiving TTL or CMOS input. The pull-up must satisfy three constraints simultaneously: it must source enough current to pull the output low, limit the low-state current, and charge the total node capacitance quickly enough for the required rise time.

The LM2903VDG can operate from 2 V to 36 V, but the common-mode input range and open-collector output voltage are separate design constraints. Do not assume that every input voltage between the supply rails is acceptable over the full temperature range. Review the manufacturer input common-mode limits and use resistor division when the sensed signal can exceed the specified input range.

Place the pull-up resistors close to the relevant output and receiver-input pins to minimize the trace length of the open-collector node. Keep the comparator input traces short and away from high-current switching paths, because 15 mV maximum input offset does not eliminate errors caused by parasitic pickup or ground movement. Use a quiet ground-return path for the reference and sensed-signal sources.

The V suffix should not be treated as a substitute for a complete qualification review. Although the LM2903 family is associated with consumer, automotive, and industrial applications, verify the ordering table, temperature grade, AEC-Q100 status, and quality documentation for the exact LM2903VDG ordering code before using it in a regulated automotive design.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The LM2903 family is described for consumer, automotive, and industrial applications, but exact RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations for LM2903VDG were not stated in the retrieved information.

Pencarian Terkait

LM2903VDG datasheet LM2903VDG pinout LM2903VDG datasheet pdf onsemi LM2903VDG LM2903VDG 8-SOIC comparator LM2903VDG open collector output LM2903VDG 2-36V LM2903VDG automotive sensor LM2903VDG vs LM2903DG LM2903VDG vs TI LM2903 LM2903VDG equivalent LM2903VDG drop-in replacement LM2903VDG price LM2903VDG stock

Komponen dan Istilah Terkait

onsemi LM2903VDG LM2903DG onsemi LM2903V Texas Instruments TI LM2903 TI LM2903V TI LM2903B dual differential voltage comparator comparator analog interface IC semiconductor open-collector output rail-to-rail input single supply operation split-supply operation 8-SOIC SOIC package family surface mount TTL CMOS input offset voltage input bias current response time
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ