LM2903VDG - Dual 2-36V Open-Collector Comparator | onsemi
MPN: LM2903VDG ✓ 啟用中LM2903VDG 概覽
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital-level indication of their relationship. The LM2903 series belongs to the comparator hierarchy, which also includes the broader category of analog interface ICs. Its two independent channels allow one package to implement two comparison functions while avoiding the common-mode limitations associated with older single-supply comparators.
The principal features of the LM2903VDG include two independent precision comparator channels, open-collector outputs suitable for pulling a logic node low, operation from a single 2 V supply or split supplies, and an extended temperature range of -40 °C to 125 °C. Maximum input offset voltage is 15 mV, maximum average input bias current is 0.5 µA, and typical response time is 1.5 µs. The open-collector architecture requires an external pull-up resistor when driving CMOS or other logic families.
Each channel contains non-inverting and inverting inputs, an output, and a common power-supply connection. The two channels operate independently, but both share the same package pins for ground and positive supply. Because the outputs are open collectors, they can remain in a high-impedance state until an external pull-up establishes the logic-high voltage. This feature also permits several open-collector outputs to share a bus when the application requires wired logic behavior.
Typical uses include automotive sensing interfaces, industrial control and monitoring circuits, battery-powered equipment, consumer electronics, and general-purpose threshold detection. A common example is comparing a divided sensor signal with a reference voltage, where the comparator output indicates whether the measured value is above or below the selected threshold. The 2 V minimum supply permits operation from low-voltage rails, while the 36 V maximum supports applications with higher industrial supply levels.
Designers should account for the open-collector output when selecting the pull-up resistor and logic family. The resistor must be small enough to achieve the required output rise time but large enough to limit pull-up current when the transistor is saturated. Input-referred offset and bias-current errors should also be included when the comparator threshold requires high accuracy.
This product page combines the exact LM2903VDG ordering information with technical characteristics, verified source links, application guidance, and same-footprint replacement analysis. It is structured to help engineers identify suitability, evaluate alternatives, and plan PCB implementation without overlooking the electrical distinctions that matter in comparator designs.
直接替換替代品,適用於 LM2903VDG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2903VDG (相同外形與佔位) — 差異在於 Package, Comparator Type, Mounting Type, Output Type, Number of Channels.
LM2903DG4
✅ 直接替換聯絡詢價
查看資料表 →LM2903VN
✅ 直接替換聯絡詢價
查看資料表 →LM2903BIDR
✅ 直接替換聯絡詢價
查看資料表 →LM2903VN
✅ 直接替換聯絡詢價
查看資料表 →LM2903BIDR
✅ 直接替換聯絡詢價
查看資料表 →LM2903VDG 最大額定值與電氣特性
| Comparator Type | Dual differential voltage comparator |
| Number of Channels | 2 independent channels |
| Supply Voltage Range | 2 V to 36 V |
| Supply Configuration | Single or split supply |
| 輸出類型 | Open collector |
| Input Common-Mode Range | Rail-to-rail |
| Maximum Input Offset Voltage | 15 mV |
| Maximum Average Input Bias Current | 0.5 µA |
| Typical Response Time | 1.5 µs |
| 工作溫度範圍 | -40 °C to 125 °C |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| Output Compatibility | TTL and CMOS |
LM2903VDG 腳位配置
| 腳位 1 | OUT 1 — Open-collector output of comparator channel 1 |
| 腳位 2 | IN− 1 — Inverting input of comparator channel 1 |
| 腳位 3 | IN+ 1 — Non-inverting input of comparator channel 1 |
| 腳位 4 | GND — Ground connection |
| 腳位 5 | IN+ 2 — Non-inverting input of comparator channel 2 |
| 腳位 6 | IN− 2 — Inverting input of comparator channel 2 |
| 腳位 7 | OUT 2 — Open-collector output of comparator channel 2 |
| 腳位 8 | VCC — Positive supply connection |
典型應用
LM2903VDG 適用於 6 應用s: Automotive Sensor Threshold Detection, Industrial Control and Monitoring, Battery-Powered Equipment, Consumer Electronics Control, Power Rail Supervision, Open-Collector Logic Interface.
Automotive Sensor Threshold Detection
The LM2903VDG fits automotive sensing circuits that compare a divided sensor voltage against a reference. Its two independent channels can monitor two conditions, such as an overvoltage threshold and an undervoltage threshold, while the extended -40 °C to 125 °C range supports harsh ambient conditions. Each channel responds in 1.5 µs typical time and has 15 mV maximum input offset voltage, so the system should budget that error in its threshold design. The open-collector output can directly pull a low-power diagnostic or logic input low, with an external pull-up setting the high voltage. Verify the exact automotive qualification and grade-specific limits in the manufacturer documentation before production use.
推薦
Industrial Control and Monitoring
The LM2903VDG is suitable for industrial control boards that must make a binary decision about an analog process or power signal. Place one channel on the non-inverting input and the other on the inverting input when independent upper and lower limits are required. Its 2 V to 36 V operating range accommodates low-voltage logic rails and higher-voltage monitoring interfaces, while the rail-to-rail input characteristic helps maximize usable signal range. The 1.5 µs typical response time supports relatively quick threshold actions. Because the outputs are open collector, use pull-up resistors matched to the receiving controller and account for the maximum output offset when setting safety or control limits.
推薦
Battery-Powered Equipment
The LM2903VDG can monitor a battery-derived system using its low 2 V minimum supply and 0.5 µA maximum average input bias current. Two independent channels may supervise a battery threshold and another system rail without using two comparator packages. The open-collector output allows a pulled-up status signal to remain in a high-impedance state when the comparator is inactive, helping reduce unnecessary load in a power-sensitive design. The rail-to-rail input capability is valuable when the monitored voltage approaches the available supply rail. Select the pull-up value to balance leakage-driven static current against the required logic rise time, and check the complete operating-temperature and supply-current limits in the device datasheet.
推薦
Consumer Electronics Control
The LM2903VDG provides economical dual-channel logic for consumer products that must convert an analog level into a switching decision. Examples include charger-state detection, display threshold control, or protection of an analog front end. Its 8-pin SOIC package supports compact surface-mount layouts, and the two channels reduce the number of packages needed when two thresholds must be evaluated. The 15 mV maximum input offset and 1.5 µs typical response time are important when defining the point at which the product changes state. An external pull-up is required for each open-collector output; keep that connection short and choose its resistance according to the input capacitance and required rise time.
推薦
Power Rail Supervision
The LM2903VDG can supervise power rails by comparing divided supply voltages with reference levels. Its two independent channels allow a single package to detect both an undervoltage and an overvoltage condition, and the rail-to-rail input range is useful in low-supply systems where the signal of interest occupies much of the available range. The device operates from 2 V to 36 V, providing flexibility across consumer, industrial, and automotive-style systems. Its open-collector outputs can drive an enable, reset, or fault input when paired with appropriate pull-ups. The 15 mV maximum offset must be included in the threshold-error budget, while the 1.5 µs typical response time determines how quickly the supervision circuit reacts.
推薦
Open-Collector Logic Interface
The LM2903VDG is appropriate when a comparator must interface with TTL, CMOS, or another open-collector-compatible logic node. The output transistor pulls the node toward ground, while an external resistor establishes the high state at the receiver's supply voltage. This arrangement offers flexibility in system partitioning because the pull-up can be tied to a local or protected rail rather than the comparator supply. Both channels are independent, permitting separate logic decisions without contention. The 2 V to 36 V supply range and 1.5 µs typical response time support many control and monitoring functions. Size the pull-up for the total input capacitance and required rise time, while confirming that the output current and saturation limits meet the worst-case load requirement.
推薦
推薦產品摘要
工程參考資料,適用於 LM2903VDG — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2903DG | LM2903V | LM2903 | LM2903V | LM2903B |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Comparator Channels | 2 independent channels | 2 independent channels | 2 independent channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
主要差異化特點
- Wide operating range for low- and high-voltage monitoring (對比LM2903DG)
- Two independent channels in a compact SOIC footprint (對比LM2903B)
- Open-collector outputs support flexible logic interfacing (對比LM2903)
設計說明
Do not connect a logic load directly to an open-collector output without a pull-up resistor. Add one resistor from each output to the supply used by the receiving TTL or CMOS input. The pull-up must satisfy three constraints simultaneously: it must source enough current to pull the output low, limit the low-state current, and charge the total node capacitance quickly enough for the required rise time.
The LM2903VDG can operate from 2 V to 36 V, but the common-mode input range and open-collector output voltage are separate design constraints. Do not assume that every input voltage between the supply rails is acceptable over the full temperature range. Review the manufacturer input common-mode limits and use resistor division when the sensed signal can exceed the specified input range.
Place the pull-up resistors close to the relevant output and receiver-input pins to minimize the trace length of the open-collector node. Keep the comparator input traces short and away from high-current switching paths, because 15 mV maximum input offset does not eliminate errors caused by parasitic pickup or ground movement. Use a quiet ground-return path for the reference and sensed-signal sources.
The V suffix should not be treated as a substitute for a complete qualification review. Although the LM2903 family is associated with consumer, automotive, and industrial applications, verify the ordering table, temperature grade, AEC-Q100 status, and quality documentation for the exact LM2903VDG ordering code before using it in a regulated automotive design.
合規資訊
The LM2903 family is described for consumer, automotive, and industrial applications, but exact RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations for LM2903VDG were not stated in the retrieved information.