STMicroelectronics

LM293DT - Dual 36V Low-Power Comparator | STMicroelectronics

MPN: LM293DT ✓ Aktif
2 V to 36 V Vdss 0.4 mA typical Id 8-pin SOIC Package
MOQ: 1 |

LM293DT Ringkasan

STMicroelectronics LM293DT is a low-power dual voltage comparator containing two independent comparator channels in an 8-pin SOIC package. Each channel supports a single supply from 2 V to 36 V or dual-supply operation, while the input stage accepts input voltages spanning the supply rails. The device uses open-collector output stages suitable for driving wired-AND, open-drain, and pull-up-based interfaces.

A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM293 belongs to the comparator hierarchy, where a comparator is a signal-conditioning IC used between sensors, amplifiers, reference voltages, and digital control logic. Its two independent channels allow one package to perform two threshold decisions, reducing component count in industrial controls, monitoring equipment, and embedded systems.

Key characteristics include very low supply current of 0.4 mA typical, 1 mW power consumption per comparator at a 5 V supply, low typical input bias current of 25 nA, and typical input offset current of ±5 nA. The typical input offset voltage is ±1 mV. Rail-to-rail input capability allows each comparator to operate with inputs near the negative and positive supply limits, while the open-collector outputs require an external pull-up resistor.

The LM293DT uses a bipolar comparator architecture optimized for low power rather than high-speed operation. Its low input currents are useful when the source impedance is high or leakage would otherwise shift the comparison threshold. Because the outputs are open collector, two or more outputs can share a pull-up node to form a wired-AND function. The external pull-up determines output rise time, so resistance and capacitance must be selected together for the required switching speed.

Typical applications include battery-powered threshold detection, sensor-signal conditioning, window comparators, overvoltage monitoring, industrial control interfaces, and simple switching regulators. The dual configuration is particularly useful when a system must monitor two independent limits or compare a measurement against both an upper and lower reference.

For reliable PCB operation, place input and output bypass capacitors close to their associated pins and route comparator inputs away from switching nodes and high-current return paths. Account for input offset voltage and common-mode limits when defining detection thresholds. The open-collector outputs must always have a pull-up unless the output is intentionally left unconnected.

This product page combines operating characteristics, application guidance, package information, and same-footprint replacement context to support faster component selection and board-level implementation.

Alternatif penggantian untuk LM293DT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian LM293DT (sama faktor bentuk dan footprint) — berbeda di dalam Package, Input Bias Current, Input Offset Voltage, Output Type, Number of Channels.

Texas Instruments
Package: 8-pin SOIC (D)
Input Bias Current: 3.5 nA
Input Offset Voltage: 0.37 mV
Bandingkan dengan LM293DT →
Texas Instruments
Package: SOIC-8 (D)
STMicroelectronics
Package: SOIC-8
Input Bias Current: 25 nA (typical)
Input Offset Voltage: 2 mV (typical)
Bandingkan dengan LM293DT →

LM293B

✅ Drop-In
📦 8-pin SOIC
documented B-version drop-in replacement with revised specifications; nominal supply-voltage maximum remains 36 V

📋 Alternatif referensi (tidak dalam katalog)

LM393B

✅ Drop-In
📦 8-pin SOIC
documented B-version replacement for LM293-family devices; revised offset and operating specifications

📋 Alternatif referensi (tidak dalam katalog)

LM2903BIDR

✅ Drop-In
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · 2 channels · Open-collector · 36 V · 2 V · 0.37 mV · 3.5 nA · 200 µA per comparator

Kontak untuk harga

Lihat Datasheet →

LM2936BMX-3.3/NOPB

✅ Drop-In
Texas Instruments
📦 8-pin SOIC
Texas Instruments · LM2936 · Linear Voltage Regulator (LDO) · Positive, Fixed · 1 · 3.3 V · +/-3% over line/load/temperature · 50 mA

Kontak untuk harga

Lihat Datasheet →

LM393DT

✅ Drop-In
STMicroelectronics
📦 8-pin SOIC
2 · 2 V to 36 V · ±1 V to ±18 V · 0.4 mA (typical) · 2 mV (typical) · 25 nA (typical) · 1.3 µs (typical) · Open Collector

✓ Ada di Gudang

$0.0461 / Satuan

Lihat Datasheet →

LM293DT Rating Maksimal & Karakteristik Listrik

Comparator Type Dual voltage comparator
Number of Channels 2 channels
Supply Voltage Range 2 V to 36 V
Single-Supply Operation 2 V to 36 V
Input Common-Mode Range Rail-to-rail
Tipe Output Open-collector, open-drain
Arus Pemuat 0.4 mA typical
Power Consumption per Comparator 1 mW at 5 V
Input Bias Current 25 nA typical
Input Offset Current ±5 nA typical
Input Offset Voltage ±1 mV typical
Paket 8-pin SOIC
Jumlah Pin 8 pins
Tipe Mounting Surface mount
Product Category Standard general-purpose comparator
Status RoHS unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

LM293DT 8-pin soic Diamant Konfigurasi Panduan

Konfigurasi pin untuk LM293DT (8-pin soic pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.

Diamant diagram pakai pakai 8-pin soic untuk LM293DT

Tidak ada data diatribut pin yang tersedia untuk LM293DT.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

LM293DT cocok untuk 6 aplikasis: Battery Threshold Monitoring, Industrial Sensor Interfacing, Overvoltage and Undervoltage Protection, Window Comparator Circuit, Low-Power Switching Control, Automotive and Equipment Status Interfacing.

⚡

Battery Threshold Monitoring

The LM293DT fits battery-powered systems that must detect a rail approaching an upper or lower operating limit. Its 2 V to 36 V supply range covers many industrial and portable supplies, while typical supply current of 0.4 mA limits standby demand. Rail-to-rail input capability allows divider-generated sense voltages to occupy most of the available range. Each open-collector output can pull a pulled-up status line low, although the pull-up and divider leakage must be included in the complete power budget.

🏭

Industrial Sensor Interfacing

The LM293DT is suitable for comparing a sensor-derived voltage with a reference signal in industrial monitoring equipment. Its low typical input bias current of 25 nA reduces loading on high-impedance sensor networks, while the ±1 mV typical input offset establishes a baseline for threshold-error design. Two channels can monitor independent limits or implement a window comparator. The open-collector outputs integrate directly with pull-up-based digital inputs, but input traces should remain away from motor, relay, and power-converter switching nodes.

🔧

Overvoltage and Undervoltage Protection

The LM293DT can supervise a power rail by comparing a scaled voltage against a reference and driving an open-collector fault signal. Its wide 2 V to 36 V operating range supports supervision across numerous industrial supply levels, and two independent channels allow simultaneous overvoltage and undervoltage detection. The low 0.4 mA typical supply current helps avoid unnecessary loading in auxiliary protection circuits. Design the divider resistance to balance input bias sensitivity, fault-level power dissipation, and the threshold error introduced by the ±1 mV typical offset.

📊

Window Comparator Circuit

Two LM293DT channels can form a window comparator that indicates whether a monitored voltage lies between an upper and lower threshold. One channel compares the input against the upper limit and the other against the lower limit; combining their open-collector outputs creates a defined in-range or out-of-range signal. The typical input offset voltage of ±1 mV directly affects trip-point accuracy, while rail-to-rail inputs improve signal utilization. Choose resistor values carefully because the reference divider and external hysteresis network can shift effective thresholds.

⚡

Low-Power Switching Control

The LM293DT can provide simple hysteretic control in low-power switching converters by comparing a feedback-derived voltage with a reference. The comparator's 0.4 mA typical supply current and 1 mW per-comparator consumption at 5 V suit lightweight regulation loops, while open-collector output stages can drive an external transistor or logic gate. Switching-node isolation is essential because high-edge-rate transitions can couple into the feedback and reference traces. Keep the hysteresis components compact and place the comparator input network away from the power-stage high-current path.

🚗

Automotive and Equipment Status Interfacing

The LM293DT can translate analog status conditions into open-collector fault signals for equipment and vehicle-related electronic systems. Its single-supply range of 2 V to 36 V covers numerous 12 V and 24 V systems, and the two channels can supervise two independent conditions. Because the standard LM293DT ordering code is not identified as an AEC-Q100-qualified variant in the available documentation, automotive production designs require separate qualification review. The completed circuit should also validate output behavior across temperature, supply range, and transient conditions.

Ringkasan Produk Direkomendasikan

LM293 Related dual comparator for threshold detection Digunakan di dalam: Battery Threshold Monitoring, Window Comparator Circuit LM293B Revised drop-in family option Digunakan di dalam: Battery Threshold Monitoring, Overvoltage and Undervoltage Protection, Low-Power Switching Control, Automotive and Equipment Status Interfacing LM393 Texas Instruments Digunakan di dalam: Industrial Sensor Interfacing, Window Comparator Circuit LM393B Revised dual comparator family option Digunakan di dalam: Industrial Sensor Interfacing, Automotive and Equipment Status Interfacing LM2903B Revised dual comparator family for voltage supervision Digunakan di dalam: Overvoltage and Undervoltage Protection, Low-Power Switching Control
What are the key specifications of LM293DT that engineers should know?
The LM293DT is a dual, low-power voltage comparator with a 2 V to 36 V supply range, rail-to-rail inputs, and open-collector outputs in an 8-pin SOIC package. According to the STMicroelectronics datasheet, its typical supply current is 0.4 mA, input bias current is 25 nA, input offset current is ±5 nA, and input offset voltage is ±1 mV. The device provides two independent comparator channels, making it suitable for dual-threshold detection and low-power sensing.
What is the LM293DT used for?
The LM293DT is used to compare two analog voltages and generate an open-collector logic output indicating the comparison result. Its two independent channels can implement upper and lower thresholds, sensor-limit detection, voltage-window monitoring, or signal conditioning. According to the STMicroelectronics datasheet, the device operates from 2 V to 36 V and has rail-to-rail input capability, allowing inputs to approach the supply rails under suitable operating conditions.
What is the supply voltage range of LM293DT?
The LM293DT operates from 2 V to 36 V when powered from a single supply. It can also use dual supplies, giving the comparator the flexibility to monitor negative and positive signals. According to the STMicroelectronics datasheet, its very low typical supply current of 0.4 mA is largely independent of supply voltage, making the device suitable for low-power and wide-range industrial applications.
Why does the LM293DT output require a pull-up resistor?
Each LM293DT output is an open-collector stage, so it can pull the output node low but cannot actively drive it high. A pull-up resistor is required to establish the high logic level. According to the STMicroelectronics datasheet, the output is compatible with TTL, MOS, and CMOS interfaces. The resistor also sets the output rise time with the total node capacitance, so faster response generally requires a lower pull-up resistance and suitable added drive capability.
Can LM293DT inputs operate near the supply rails?
Yes, the LM293DT supports rail-to-rail common-mode input operation. According to the STMicroelectronics datasheet, this allows the input voltages to extend close to the negative and positive supply rails. Rail-to-rail input capability is valuable in battery-powered monitoring because useful sensor or divider signals can occupy most of the available supply range. Input offset and bias errors should still be included when defining precise trip points.
Where can I download the LM293DT datasheet PDF?
The LM293DT datasheet PDF can be obtained through the manufacturer documentation link or the datasheet reference page for this 8-pin SOIC device. The document identifies the part as a low-power dual voltage comparator and provides the electrical characteristics, pin configuration, and application information. Use the STMicroelectronics LM293 datasheet for design decisions because later-family documents may specify different parameters or improved variants.
Where can I find the LM293DT pinout?
The LM293DT pinout is shown in the pin-configuration section of the STMicroelectronics LM293 datasheet. The part contains two comparator channels in an 8-pin SOIC package, with output pins returned to ground through open-collector structures. Before assigning PCB tracks, verify signal names and numbering against the diagram for the specific LM293DT ordering code because an SOIC drawing alone does not identify every terminal function.
What can replace the LM293DT?
The closest documented replacement is the improved B-version of the LM293 family, which is described as a drop-in replacement for LM293 devices. Compatibility must still be confirmed for the exact package, electrical limits, and application requirements. According to the Texas Instruments LM293 product information, the B-version provides improved specifications while retaining compatibility with established LM293-family systems.
Is LM293DT the same as LM293B?
The LM293DT and LM293B are closely related, but they are not identical ordering codes. According to the Texas Instruments LM293 product information, the B-version is a drop-in replacement for LM293-family devices and offers improved specifications. The LM293DT is the STMicroelectronics 8-pin SOIC version, so engineers should verify manufacturer, package, operating limits, and input/output behavior before treating the B-version as a production substitute.
What is the best Texas Instruments equivalent for LM293DT?
The Texas Instruments LM293B is the most directly documented cross-brand equivalent because the manufacturer identifies the B-version as a drop-in replacement for LM293. It is available in an 8-pin SOIC configuration for corresponding orderable variants. According to the Texas Instruments LM293 product information, the B-version retains the established comparator architecture while improving specified electrical performance, making it the preferred starting point for a board-level substitution review.
LM293DT vs LM293B — which is better for an industrial threshold detector?
The LM293B is generally preferred for a new design when its improved electrical specifications and documented drop-in relationship are important, while the LM293DT remains appropriate for established STMicroelectronics designs. Both belong to the low-power dual-comparator family, but package order codes, qualification, sourcing, and parameter limits must be checked. According to the Texas Instruments LM293 product information, the B-version is a drop-in replacement for LM293.
What is the difference between LM293DT and LM393B?
The LM293DT and LM393B are dual open-collector comparators from related product families, but they are not guaranteed identical for every design. According to the Texas Instruments LM293 product information, the B-version of LM393 is a drop-in replacement for LM293, while the document also identifies improvements specific to the B-version. Review input offset, supply current, common-mode limits, and the exact package before substitution.
When should I choose LM293DT over LM293B?
Choose the LM293DT when maintaining an STMicroelectronics-based design, matching an existing approved BOM, or preserving the LM293DT order code and package qualification is important. Choose the improved B-version family when a documented drop-in relationship and revised specifications justify requalification. The decision should be based on the exact alternate part, operating environment, supply availability, and validation performed for the finished assembly.
Is LM293DT suitable for battery-powered monitoring?
The LM293DT is suitable for battery-powered monitoring because its typical supply current is only 0.4 mA and each comparator consumes about 1 mW at a 5 V supply. According to the STMicroelectronics datasheet, supply current remains largely independent of supply voltage across the supported range. Rail-to-rail inputs help maximize the usable signal span, although leakage from external divider resistors can dominate the overall standby power.
How should a pull-up resistor be selected for LM293DT?
Select the pull-up resistor by balancing output rise time, sink-current capability, power consumption, and the voltage tolerated by the output stage. A lower resistance produces a faster rising edge but increases sink current and static dissipation; a higher resistance reduces power but slows transitions when capacitance is present. According to the STMicroelectronics datasheet, the open-collector output can interface with TTL, MOS, and CMOS systems when the pull-up voltage is selected correctly.
Where can I request a quote for LM293DT?
Use the Request a Quote form on this page to request current LM293DT commercial terms, quantity availability, and lead time. The form is the appropriate channel for a quote because market pricing and inventory can change without notice. Confirm the exact package suffix, tape-and-reel requirements, target quantity, and delivery schedule before releasing an order.

Data referensi engineering untuk LM293DT — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the LM293DT when a design requires two independent, low-power comparator channels, rail-to-rail input capability, and open-collector outputs in an 8-pin SOIC. Its 0.4 mA typical supply current, 25 nA typical input bias current, and ±1 mV typical input offset are particularly useful in battery systems and high-impedance sensor circuits. Choose LM293B when the manufacturer’s documented drop-in relationship and revised B-version specifications justify requalification. Choose LM393B or LM2903B when their B-version revisions are preferred within the broader comparator family, but verify their exact common-mode, supply, and timing limits. Choose LM293 or LM393 when an established family configuration or sourcing requirement dominates. For every substitute, confirm the exact SOIC orderable package, pin assignment, input thresholds, output pull-up arrangement, temperature range, qualification status, and behavior across supply and temperature extremes.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini LM293B LM393B LM2903B LM293 LM393
Brand STMicroelectronics Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Comparator Channels 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Output Type Open-collector, open-drain Open-collector Open-collector Open-collector Open-collector Open-collector
— —
— —
— —
— —
— —

Diferensiator Kunci

  • Lowest specified supply current in the comparison set (vsLM293B)
  • Very low input bias supports high-impedance sensing (vsLM293B)
  • Low offset voltage supports tighter threshold definition (vsLM393B)
  • Dual rail-to-rail-input capability in one package (vsLM2903B)

Catatan Desain

Place input resistors, reference-divider components, and any hysteresis capacitors close to the corresponding LM293DT pins. Comparator inputs are sensitive to coupling even though the device itself draws only 0.4 mA typical. Route both comparison inputs away from switching-node copper, relay contacts, inductors, and high-current supply paths. Use a continuous ground reference under the device and keep the external pull-up return path short to minimize susceptibility to common-mode transients.

Do not assume that an open-collector output can rise without an external pull-up. Select the pull-up voltage for the connected TTL, MOS, or CMOS interface and verify the maximum sink current with the chosen resistor. The LM293DT typical input offset voltage is ±1 mV, so add that error, reference tolerance, and resistor tolerance when calculating threshold limits. High-value dividers can also introduce errors through the 25 nA typical input bias current.

The typical supply current of 0.4 mA is a key advantage in battery systems, but total standby current also includes the voltage-divider and pull-up networks. Size those resistors to limit their contribution without allowing input bias current to move the comparison threshold. Estimated: a 100 kΩ divider presents 50 kΩ to the input and can contribute approximately 20 nA at a 1 V node, which is comparable to the comparator's 25 nA typical input bias current.

When the open-collector output drives a cable, relay, or long digital trace, keep the pull-up resistor near the receiving device and consider the cable capacitance and ringing. A low pull-up resistance improves rise time but increases sink current and dissipation. Validate the complete output path with an oscilloscope across temperature and supply extremes because comparator transition timing, board capacitance, and pull-up tolerance jointly determine signal integrity.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

No RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was included in the component documentation. The standard LM293DT ordering code should not be assumed to be AEC-Q100 qualified.

Data disahkan pada: 2026-11-10 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

lm293dt datasheet LM293DT pinout LM293DT datasheet pdf LM293DT equivalent LM293DT replacement LM293DT vs LM293B LM293DT cross reference LM293DT application circuit LM293DT SOIC-8 comparator STMicroelectronics LM293DT LM293DT price LM293DT stock

Komponen dan Istilah Terkait

STMicroelectronics Texas Instruments LM293DT LM293B LM393B LM2903B LM293 LM393 voltage comparator dual comparator analog comparator signal-conditioning IC open-collector output open-drain output rail-to-rail input supply current input bias current input offset current input offset voltage power consumption 8-pin SOIC SOIC family surface-mount package battery-powered monitoring industrial sensor interfacing
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ