LM293DT - Dual 36V Low-Power Comparator | STMicroelectronics
MPN: LM293DT ✓ Hoạt độngLM293DT Tóm tắt
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM293 belongs to the comparator hierarchy, where a comparator is a signal-conditioning IC used between sensors, amplifiers, reference voltages, and digital control logic. Its two independent channels allow one package to perform two threshold decisions, reducing component count in industrial controls, monitoring equipment, and embedded systems.
Key characteristics include very low supply current of 0.4 mA typical, 1 mW power consumption per comparator at a 5 V supply, low typical input bias current of 25 nA, and typical input offset current of ±5 nA. The typical input offset voltage is ±1 mV. Rail-to-rail input capability allows each comparator to operate with inputs near the negative and positive supply limits, while the open-collector outputs require an external pull-up resistor.
The LM293DT uses a bipolar comparator architecture optimized for low power rather than high-speed operation. Its low input currents are useful when the source impedance is high or leakage would otherwise shift the comparison threshold. Because the outputs are open collector, two or more outputs can share a pull-up node to form a wired-AND function. The external pull-up determines output rise time, so resistance and capacitance must be selected together for the required switching speed.
Typical applications include battery-powered threshold detection, sensor-signal conditioning, window comparators, overvoltage monitoring, industrial control interfaces, and simple switching regulators. The dual configuration is particularly useful when a system must monitor two independent limits or compare a measurement against both an upper and lower reference.
For reliable PCB operation, place input and output bypass capacitors close to their associated pins and route comparator inputs away from switching nodes and high-current return paths. Account for input offset voltage and common-mode limits when defining detection thresholds. The open-collector outputs must always have a pull-up unless the output is intentionally left unconnected.
This product page combines operating characteristics, application guidance, package information, and same-footprint replacement context to support faster component selection and board-level implementation.
Bộ thay thế dễ dàng lắp đặt cho LM293DT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM293DT (cùng hình factor và footprint) — khác nhau ở Package, Input Bias Current, Input Offset Voltage, Output Type, Number of Channels.
LM293B
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM393B
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2903BIDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2936BMX-3.3/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393DT
✅ Drop-In✓ Còn hàng
$0.0461 / Đơn vị
Xem tài liệu →LM293DT Tỷ lệ tối đa & tính chất điện
| Comparator Type | Dual voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2 V to 36 V |
| Single-Supply Operation | 2 V to 36 V |
| Input Common-Mode Range | Rail-to-rail |
| Kiểu đầu ra | Open-collector, open-drain |
| Điện áp cung cấp | 0.4 mA typical |
| Power Consumption per Comparator | 1 mW at 5 V |
| Input Bias Current | 25 nA typical |
| Input Offset Current | ±5 nA typical |
| Input Offset Voltage | ±1 mV typical |
| Hộp | 8-pin SOIC |
| Số lượng chân | 8 pins |
| Kiểu lắp đặt | Surface mount |
| Product Category | Standard general-purpose comparator |
| Trạng thái RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Hướng dẫn cấu hình chân LM293DT 8-pin soic
Cấu hình chân cho LM293DT (8-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM293DT.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM293DT phù hợp cho 6 Áp dụngs: Battery Threshold Monitoring, Industrial Sensor Interfacing, Overvoltage and Undervoltage Protection, Window Comparator Circuit, Low-Power Switching Control, Automotive and Equipment Status Interfacing.
Battery Threshold Monitoring
The LM293DT fits battery-powered systems that must detect a rail approaching an upper or lower operating limit. Its 2 V to 36 V supply range covers many industrial and portable supplies, while typical supply current of 0.4 mA limits standby demand. Rail-to-rail input capability allows divider-generated sense voltages to occupy most of the available range. Each open-collector output can pull a pulled-up status line low, although the pull-up and divider leakage must be included in the complete power budget.
Được đề xuất
Industrial Sensor Interfacing
The LM293DT is suitable for comparing a sensor-derived voltage with a reference signal in industrial monitoring equipment. Its low typical input bias current of 25 nA reduces loading on high-impedance sensor networks, while the ±1 mV typical input offset establishes a baseline for threshold-error design. Two channels can monitor independent limits or implement a window comparator. The open-collector outputs integrate directly with pull-up-based digital inputs, but input traces should remain away from motor, relay, and power-converter switching nodes.
Được đề xuất
Overvoltage and Undervoltage Protection
The LM293DT can supervise a power rail by comparing a scaled voltage against a reference and driving an open-collector fault signal. Its wide 2 V to 36 V operating range supports supervision across numerous industrial supply levels, and two independent channels allow simultaneous overvoltage and undervoltage detection. The low 0.4 mA typical supply current helps avoid unnecessary loading in auxiliary protection circuits. Design the divider resistance to balance input bias sensitivity, fault-level power dissipation, and the threshold error introduced by the ±1 mV typical offset.
Được đề xuất
Window Comparator Circuit
Two LM293DT channels can form a window comparator that indicates whether a monitored voltage lies between an upper and lower threshold. One channel compares the input against the upper limit and the other against the lower limit; combining their open-collector outputs creates a defined in-range or out-of-range signal. The typical input offset voltage of ±1 mV directly affects trip-point accuracy, while rail-to-rail inputs improve signal utilization. Choose resistor values carefully because the reference divider and external hysteresis network can shift effective thresholds.
Được đề xuất
Low-Power Switching Control
The LM293DT can provide simple hysteretic control in low-power switching converters by comparing a feedback-derived voltage with a reference. The comparator's 0.4 mA typical supply current and 1 mW per-comparator consumption at 5 V suit lightweight regulation loops, while open-collector output stages can drive an external transistor or logic gate. Switching-node isolation is essential because high-edge-rate transitions can couple into the feedback and reference traces. Keep the hysteresis components compact and place the comparator input network away from the power-stage high-current path.
Được đề xuất
Automotive and Equipment Status Interfacing
The LM293DT can translate analog status conditions into open-collector fault signals for equipment and vehicle-related electronic systems. Its single-supply range of 2 V to 36 V covers numerous 12 V and 24 V systems, and the two channels can supervise two independent conditions. Because the standard LM293DT ordering code is not identified as an AEC-Q100-qualified variant in the available documentation, automotive production designs require separate qualification review. The completed circuit should also validate output behavior across temperature, supply range, and transient conditions.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM293DT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM293B | LM393B | LM2903B | LM293 | LM393 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Comparator Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open-collector, open-drain | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| — | — | |||||
| — | — | |||||
| — | — | |||||
| — | — | |||||
| — | — |
Bảo phân biệt quan trọng
- Lowest specified supply current in the comparison set (vsLM293B)
- Very low input bias supports high-impedance sensing (vsLM293B)
- Low offset voltage supports tighter threshold definition (vsLM393B)
- Dual rail-to-rail-input capability in one package (vsLM2903B)
Ghi chú thiết kế
Place input resistors, reference-divider components, and any hysteresis capacitors close to the corresponding LM293DT pins. Comparator inputs are sensitive to coupling even though the device itself draws only 0.4 mA typical. Route both comparison inputs away from switching-node copper, relay contacts, inductors, and high-current supply paths. Use a continuous ground reference under the device and keep the external pull-up return path short to minimize susceptibility to common-mode transients.
Do not assume that an open-collector output can rise without an external pull-up. Select the pull-up voltage for the connected TTL, MOS, or CMOS interface and verify the maximum sink current with the chosen resistor. The LM293DT typical input offset voltage is ±1 mV, so add that error, reference tolerance, and resistor tolerance when calculating threshold limits. High-value dividers can also introduce errors through the 25 nA typical input bias current.
The typical supply current of 0.4 mA is a key advantage in battery systems, but total standby current also includes the voltage-divider and pull-up networks. Size those resistors to limit their contribution without allowing input bias current to move the comparison threshold. Estimated: a 100 kΩ divider presents 50 kΩ to the input and can contribute approximately 20 nA at a 1 V node, which is comparable to the comparator's 25 nA typical input bias current.
When the open-collector output drives a cable, relay, or long digital trace, keep the pull-up resistor near the receiving device and consider the cable capacitance and ringing. A low pull-up resistance improves rise time but increases sink current and dissipation. Validate the complete output path with an oscilloscope across temperature and supply extremes because comparator transition timing, board capacitance, and pull-up tolerance jointly determine signal integrity.
Thông tin tuân thủ
No RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was included in the component documentation. The standard LM293DT ordering code should not be assumed to be AEC-Q100 qualified.