LTC2294CUP - Dual 12-Bit 80Msps 3V ADC | Analog Devices
MPN: LTC2294CUP ✓ AktifLTC2294CUP Ringkasan
An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous analog voltages and outputs discrete digital codes at a fixed sampling rate. Pipelined ADCs, the architecture used in the LTC2294, cascade multiple low-resolution flash stages to achieve high sample rates (tens of Msps and above) with moderate power consumption and small die area. This makes them the dominant architecture for communications, imaging, and instrumentation applications requiring conversion of IF or baseband signals in the 1-100 MHz range.
Key specifications include 70.6 dB SNR and 90 dB SFDR at 70 MHz input, ±0.4 LSB INL (typical), ±0.2 LSB DNL (typical), 110 dB channel isolation at 100 MHz, and a flexible input range of 1 Vp-p to 2 Vp-p. Optional internal dither is provided to improve SFDR when the input approaches full-scale and the spectrum would otherwise exhibit integral non-linearity spurs. A separate output supply pin permits the digital outputs to drive 3V, 2.5V, or 1.8V logic without level shifters.
Typical applications include cellular base-station IF sampling, multi-channel imaging arrays, portable test and measurement front-ends, ultrasound beamformers, and low-cost digital oscilloscope input channels. The combination of dual channels and low power also suits multi-antenna diversity receivers in software-defined radio.
When designing with this part, allocate the exposed pad directly under the package to a continuous ground pour and stitch it with at least 9 thermal vias to the inner ground plane. Drive the analog inputs with a low-impedance differential buffer (such as the AD8138 or AD8352) and bypass both AVDD and OVDD pins with 0.1uF ceramic capacitors placed within 2 mm of each pin.
This page aggregates distributor pricing, drop-in LTC22xx/LTC23xx family alternatives, and PCB/thermal design guidance not present in the manufacturer datasheet, providing information gain beyond stock parametric listings.
Alternatif penggantian untuk LTC2294CUP — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian LTC2294CUP (sama faktor bentuk dan footprint) — berbeda di dalam Operating Temperature, Package, Power Dissipation, SNR, RoHS Status.
LTC2294IUP
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LTC2294CUP#PBF
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LTC2294CUP#TRPBF
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LTC2292CUP
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →LTC2287CUP
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →LTC2282CUP
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →LTC2294CUP Rating Maksimal & Karakteristik Listrik
| Resolusi | 12 bits |
| Number of Channels | 2 (dual, simultaneous sampling) |
| Sampling Rate (max) | 80 Msps |
| Architecture | Pipelined |
| Supply Voltage (AVDD) | 2.7 V to 3.4 V (single 3V supply) |
| Output Supply (OVDD) | 1.8 V / 2.5 V / 3 V selectable |
| Power Dissipation | 422 mW (typical, both channels, 80 Msps) |
| SNR | 70.6 dB at 70 MHz input |
| SFDR | 90 dB at 70 MHz input |
| INL | +/-0.4 LSB typical |
| DNL | +/-0.2 LSB typical |
| Channel Isolation | 110 dB at 100 MHz |
| Input Range | 1 Vp-p to 2 Vp-p (flexible) |
| Data Bus Mode | Multiplexed or separate (2x/1x clock options) |
| Suhu Kerja | 0C to +70C (commercial, C grade) |
| Paket | 64-pin QFN (UP) 9x9 mm with exposed pad |
| Internal Dither | Optional (improves SFDR at near-FS) |
| Status RoHS | Compliant (#PBF suffix) |
| 1ku List Price (LTC2294 family, starting) | $40.85 |
Konfigurasi Pin LTC2294CUP
| Pin produk 1 | AIN1A+ — Channel 1 analog input positive |
| Pin produk 2 | AIN1A- — Channel 1 analog input negative |
| Pin produk 3 | SENSE1 — Channel 1 reference/programming |
| Pin produk 4 | VCM1 — Channel 1 input common-mode voltage |
| Pin produk 5 | REFT1 — Channel 1 top reference decoupling |
| Pin produk 6 | REFB1 — Channel 1 bottom reference decoupling |
| Pin produk 7 | VD1 — Channel 1 analog supply decoupling |
| Pin produk 8 | GND1 — Channel 1 analog ground |
| Pin produk 9 | AIN1B+ — Channel 1 second ADC input positive |
| Pin produk 10 | AIN1B- — Channel 1 second ADC input negative |
| Pin produk 11 | NC — Not connected (per datasheet) |
| Pin produk 12 | DITH1 — Channel 1 dither control |
| Pin produk 13 | AVDD — Analog 3V supply |
| Pin produk 14 | AGND — Analog ground |
| Pin produk 15 | VREF — Internal reference decoupling |
| Pin produk 16 | VREFT — Top reference decoupling |
| Pin produk 17 | VREFB — Bottom reference decoupling |
| Pin produk 18 | REFT2 — Channel 2 top reference decoupling |
| Pin produk 19 | REFB2 — Channel 2 bottom reference decoupling |
| Pin produk 20 | GND2 — Channel 2 analog ground |
| Pin produk 21 | VD2 — Channel 2 analog supply decoupling |
| Pin produk 22 | DITH2 — Channel 2 dither control |
| Pin produk 23 | NC — Not connected (per datasheet) |
| Pin produk 24 | SENSE2 — Channel 2 reference/programming |
| Pin produk 25 | VCM2 — Channel 2 input common-mode voltage |
| Pin produk 26 | AIN2A+ — Channel 2 analog input positive |
| Pin produk 27 | AIN2A- — Channel 2 analog input negative |
| Pin produk 28 | AIN2B+ — Channel 2 second ADC input positive |
| Pin produk 29 | AIN2B- — Channel 2 second ADC input negative |
| Pin produk 30 | NC — Not connected (per datasheet) |
| Pin produk 31 | OVDD — Output driver supply |
| Pin produk 32 | OGND — Output driver ground |
| Pin produk 33 | CLKOUT — Clock output for latching data |
| Pin produk 34 | OF — Output format select |
| Pin produk 35 | ENC+ — Encode clock positive input |
| Pin produk 36 | ENC- — Encode clock negative input |
| Pin produk 37 | OGND — Output driver ground |
| Pin produk 38 | OVDD — Output driver supply |
| Pin produk 39 | DA0 — Channel 2 data output bit 0 |
| Pin produk 40 | DA1 — Channel 2 data output bit 1 |
| Pin produk 41 | DA2 — Channel 2 data output bit 2 |
| Pin produk 42 | DA3 — Channel 2 data output bit 3 |
| Pin produk 43 | DA4 — Channel 2 data output bit 4 |
| Pin produk 44 | DA5 — Channel 2 data output bit 5 |
| Pin produk 45 | DA6 — Channel 2 data output bit 6 |
| Pin produk 46 | DA7 — Channel 2 data output bit 7 |
| Pin produk 47 | DA8 — Channel 2 data output bit 8 |
| Pin produk 48 | DA9 — Channel 2 data output bit 9 |
| Pin produk 49 | DA10 — Channel 2 data output bit 10 |
| Pin produk 50 | DA11 — Channel 2 data output bit 11 (MSB) |
| Pin produk 51 | DB0 — Channel 1 data output bit 0 |
| Pin produk 52 | DB1 — Channel 1 data output bit 1 |
| Pin produk 53 | DB2 — Channel 1 data output bit 2 |
| Pin produk 54 | DB3 — Channel 1 data output bit 3 |
| Pin produk 55 | DB4 — Channel 1 data output bit 4 |
| Pin produk 56 | DB5 — Channel 1 data output bit 5 |
| Pin produk 57 | DB6 — Channel 1 data output bit 6 |
| Pin produk 58 | DB7 — Channel 1 data output bit 7 |
| Pin produk 59 | DB8 — Channel 1 data output bit 8 |
| Pin produk 60 | DB9 — Channel 1 data output bit 9 |
| Pin produk 61 | DB10 — Channel 1 data output bit 10 |
| Pin produk 62 | DB11 — Channel 1 data output bit 11 (MSB) |
| Pin produk 63 | OVDD — Output driver supply |
| Pin produk 64 | OGND — Output driver ground |
Aplikasi Umum
LTC2294CUP cocok untuk 6 aplikasis: Cellular Base-Station IF Sampling, Multi-Channel Imaging Arrays, Portable Test and Measurement Front-Ends, Ultrasound Beamforming Receivers, Software-Defined Radio Diversity Receivers, Low-Cost Digital Oscilloscope Input Channel.
Cellular Base-Station IF Sampling
The LTC2294CUP is well matched to intermediate-frequency (IF) sampling in cellular base-station receivers because its 80 Msps per-channel rate digitizes 70 MHz IF signals with significant margin above the Nyquist limit while preserving 70.6 dB SNR. Two simultaneous channels on one die reduce board area versus two discrete ADCs and eliminate channel-to-channel gain/offset mismatch. Reference: LTC2294 datasheet 2294fa communications section.
Direkomendasikan
Multi-Channel Imaging Arrays
For CCD/CIS image sensor front-ends, the LTC2294CUP samples two channels simultaneously at 80 Msps with 110 dB channel isolation, which suppresses crosstalk from the adjacent pixel channel. The 422 mW total power keeps 4-channel and 8-channel arrays within manageable thermal envelopes. According to LTC2294 datasheet 2294fa, the dither option improves SFDR when the input approaches the full-scale rail.
Direkomendasikan
Portable Test and Measurement Front-Ends
Handheld oscilloscopes and spectrum analyzers benefit from the LTC2294CUP's 70.6 dB SNR and 80 Msps combined with 422 mW total power. Two channels at one IC halve the PCB area of the analog front-end, which is critical for compact portable enclosures. The exposed pad on the 64-pin QFN dissipates heat directly into the chassis ground plane, eliminating a discrete heatsink.
Direkomendasikan
Ultrasound Beamforming Receivers
The dual simultaneous 80 Msps channels of the LTC2294CUP allow two adjacent transducer elements to be digitized on the same clock edge, supporting analog beamformer I/Q demodulation chains. With 70.6 dB SNR the device preserves 12-bit dynamic range required for B-mode ultrasound imaging. Reference: LTC2294 datasheet 2294fa medical imaging typical application.
Direkomendasikan
Software-Defined Radio Diversity Receivers
Multi-antenna diversity receivers digitize two RF chains simultaneously; the LTC2294CUP's dual channels and 110 dB isolation at 100 MHz prevent one antenna's signal from leaking into the other. The 80 Msps rate supports direct sampling of IF outputs from low-IF tuner ICs. Per LTC2294 datasheet 2294fa, the multiplexed bus mode halves the FPGA pin count when a small device is targeted.
Direkomendasikan
Low-Cost Digital Oscilloscope Input Channel
The LTC2294CUP delivers 70.6 dB SNR (about 11.5 effective bits) at 80 Msps, sufficient for entry-level 200 MHz bandwidth oscilloscope input channels. Two channels per IC support 2-channel entry products without a second ADC. The exposed pad 64-pin QFN package allows direct PCB-mounting into a scope's main board with no heatsink.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk LTC2294CUP — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | LTC2294IUP | LTC2294CUP#PBF | LTC2294CUP#TRPBF | LTC2292CUP | LTC2287CUP | LTC2282CUP |
|---|---|---|---|---|---|---|---|
| Package | 64-pin QFN (UP) 9x9 mm | 64-pin QFN (UP) 9x9 mm | 64-pin QFN (UP) 9x9 mm | 64-pin QFN (UP) 9x9 mm | 64-pin QFN (UP) 9x9 mm | 64-pin QFN (UP) 9x9 mm | 64-pin QFN (UP) 9x9 mm |
| Brand | Analog Devices (Linear Tech) | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits |
| Channels | 2 (dual) | 2 | 2 | 2 | 2 | 2 | 1 |
| Sample Rate (max) | 80 Msps | 80 Msps | 80 Msps | 80 Msps | 40 Msps | 10 Msps | 105 Msps |
| SNR (at 70 MHz) | 70.6 dB | 70.6 dB | 70.6 dB | 70.6 dB | 71.0 dB | 70.0 dB | 70.5 dB |
| Power Dissipation | 422 mW | 422 mW | 422 mW | 422 mW | 200 mW | 230 mW | 640 mW |
| Temperature Grade | 0C to +70C (Commercial) | -40C to +85C (Industrial) | 0C to +70C | 0C to +70C | 0C to +70C | 0C to +70C | 0C to +70C |
Diferensiator Kunci
- Dual simultaneous 80 Msps channels on a single 3V supply (vsLTC2208IUP)
- Pin-compatible family spanning 10 to 105 Msps (vsLTC2287CUP)
- 110 dB channel isolation at 100 MHz (vsGeneric dual ADC pairs)
Catatan Desain
Solder the exposed thermal pad (EP) of the LTC2294CUP to a continuous ground pour on the top layer and stitch it with at least 9 thermal vias (0.3 mm drill) to the inner ground plane. Place AVDD bypass capacitors (0.1uF ceramic in parallel with 10uF tantalum) within 2 mm of every AVDD pin. Per LTC2294 datasheet 2294fa PCB layout section, routing the analog inputs as a 100 ohm differential microstrip with 2W spacing minimizes reflections and preserves the 90 dB SFDR.
Drive the LTC2294CUP analog inputs with a low-impedance differential buffer (AD8138 or AD8352). Single-ended drive reduces SNR by 6 dB and degrades SFDR by 8-12 dB. Maintain 50 ohm transmission-line impedance from the buffer output to the AIN pins using controlled-impedance traces. Use an aperture delay-matched clock source (e.g., AD9520) to keep ENC edge-to-ENC phase noise below 0.5 ps RMS; this is essential to hit the rated 70.6 dB SNR at full input frequency.
Do not leave the OF (output format) pin floating - tie it to OVDD for offset-binary mode or to OGND for two's complement. Failing to do this causes the digital outputs to enter an invalid state at power-up. Also, decouple the REFT1/REFB1 and REFT2/REFB2 reference pins individually - sharing a single bypass cap between channels can couple switching noise from channel 1 into channel 2 and break the 110 dB isolation spec.
Estimated: at 422 mW total dissipation in a 64-pin QFN 9x9 mm with the EP soldered to a 4-layer FR4 board (typical theta_JA around 30 C/W per JEDEC EIA/JESD51), the junction temperature rise above ambient is approximately 13C. Within the 0C to +70C commercial range this is comfortable, but in sealed enclosures without airflow the ambient should be kept below 57C to stay within spec.
Informasi Konformitas
RoHS compliance indicated by #PBF suffix per Linear Technology/Analog Devices convention. C-grade part (0C to +70C) is not AEC-Q100 qualified; choose LTC2294IUP for industrial temperature or contact Analog Devices for automotive-grade options.
