MAX232AMJE/883B - Military RS-232 Transceiver | Analog Devices
MPN: MAX232AMJE/883B ✓ AktifMAX232AMJE/883B Ringkasan
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts incoming RS-232 signals back into logic-level outputs. Within the interface hierarchy, the MAX232 belongs to the line-driver and line-receiver category, supports bidirectional serial communication, and eliminates the need for a separate ±12 V supply when only a single +5 V rail is available.
The MAX232AMJE/883B combines two drivers and two receivers in one 16-CDIP package. Its +5 V operating supply, through-hole construction, and 0.300-inch, 7.62 mm row spacing suit industrial, telecommunications, instrumentation, and embedded control equipment where a rugged ceramic dual-inline package is preferred. The device supports both point-to-point and multipoint RS-232 communication arrangements.
Its mixed-signal operating characteristics determine several practical design constraints. RS-232 drivers use charge-pump circuitry to generate positive and negative line voltages from the +5 V supply, while the receivers detect valid bipolar signals. External bypass and charge-pump capacitors must be connected close to their designated pins, and long cables require attention to capacitive loading, common-mode voltage, ground continuity, and protection from electrostatic discharge.
Typical uses include industrial serial consoles, data acquisition systems, test equipment, remote-control interfaces, and legacy peripheral connections. The device is especially relevant where equipment retains an RS-232 port but has moved from ±12 V or ±15 V supplies to a +5 V logic environment. Its military temperature grade also supports equipment intended for extended environmental ranges.
For PCB layout, route RS-232 driver and receiver traces as differential pairs where practical, keep the external capacitors compact, and provide adequate ground return current. Protection networks should be placed where cables enter the assembly rather than directly beside the IC. Confirm capacitor type, voltage rating, pinout, and loopback behavior against the manufacturer datasheet before releasing a production layout.
This product page combines the manufacturer interface description with practical procurement and engineering guidance, including package information, qualification details, design notes, and a focused drop-in comparison. It is intended to help engineers determine whether the MAX232AMJE/883B fits the electrical, mechanical, environmental, and sourcing requirements of a specific RS-232 design.
Alternatif penggantian untuk MAX232AMJE/883B — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
MAX232AEPE+
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MAX232AMJE/883
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
MAX232AMJE/883A
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
MAX232AMJE/883B Spesifikasi
| Product Type | Dual RS-232 driver and dual receiver transceiver |
| Driver Count | 2 drivers |
| Receiver Count | 2 receivers |
| Tegangan Pemuat | 5 V |
| Interface Standard | EIA/TIA-232E and V.28/V.24 |
| Paket | 16-CDIP, 0.300-inch (7.62 mm) row spacing |
| Terminal Count | 16 terminals |
| Gaya Mounting | Through-hole |
| Suhu Kerja | -55°C to +125°C |
| Temperature Grade | Military |
| Packing Method | Tube |
MAX232AMJE/883B 16-cdip, 0.300-inch (7.62 mm) row spacing Diamant Konfigurasi Panduan
Konfigurasi pin untuk MAX232AMJE/883B (16-cdip, 0.300-inch (7.62 mm) row spacing pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk MAX232AMJE/883B.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MAX232AMJE/883B cocok untuk 6 aplikasis: Industrial Serial Console, Telecommunications Equipment Interface, Data Acquisition System, Legacy Peripheral Connectivity, Embedded Control and Monitoring, Test and Measurement Instrumentation.
Industrial Serial Console
The MAX232AMJE/883B is appropriate for an industrial console that converts +5 V UART logic into RS-232 levels and receives two remote command channels. Its two-driver and two-receiver arrangement supports bidirectional point-to-point links, while the -55°C to +125°C operating range covers equipment intended for extended industrial environments. The 16-CDIP package is practical for through-hole industrial controllers and serviceable control boards. Place the manufacturer's prescribed charge-pump capacitors near the IC, route driver and receiver traces away from switching nodes, and use protected connector-side circuits for cables entering the enclosure.
Direkomendasikan
Telecommunications Equipment Interface
The MAX232AMJE/883B can connect legacy telecommunications control electronics to RS-232 service ports using only a +5 V rail. Two driver channels support separate transmit paths, and two receiver channels support status or command inputs. Its military temperature operation and 16-CDIP construction suit rugged equipment platforms where environmental range and through-hole serviceability matter. The implementation should preserve the MAX232 family charge-pump network, provide a low-impedance ground reference, and protect connector inputs against surge and electrostatic discharge transients common on external communication lines.
Direkomendasikan
Data Acquisition System
The MAX232AMJE/883B is useful in laboratory and industrial data-acquisition equipment that must exchange commands and measurements with RS-232 instruments. The +5 V supply simplifies system power design, and the two transmit and two receive channels allow one driver-receiver pair for control traffic and another for data or status. The device's -55°C to +125°C range supports wide environmental deployments, while the CDIP package simplifies insertion into rugged instrument boards. Keep external capacitors short, provide a continuous signal-ground return, and isolate the RS-232 cable entry to prevent transients from reaching sensitive acquisition circuitry.
Direkomendasikan
Legacy Peripheral Connectivity
The MAX232AMJE/883B provides a practical bridge between modern +5 V embedded logic and legacy equipment using RS-232. Two driver outputs and two receiver inputs are sufficient for common control, status, and handshake arrangements without requiring separate line-driver ICs. Its military-temperature grade and through-hole package are advantageous for long-lived industrial, transportation, and medical-support equipment. Validate input levels and driver polarity for each legacy peripheral, then protect the cable connection with appropriately rated components. Do not substitute a surface-mount package unless the PCB is physically redesigned.
Direkomendasikan
Embedded Control and Monitoring
The MAX232AMJE/883B fits embedded controllers that need a legacy RS-232 service port in addition to a primary communications interface. Operating from +5 V allows the transceiver to share a regulated logic rail, and its 16-CDIP footprint supports ruggedized controller boards assembled with through-hole components. Two RS-232 channels can carry commands and diagnostic information between a remote terminal and a central controller. Use the manufacturer's pin-description table to assign inputs and outputs, maintain short capacitor connections, and provide a solid chassis-to-board ground strategy for reliable operation with cable-mounted equipment.
Direkomendasikan
Test and Measurement Instrumentation
The MAX232AMJE/883B can add a conventional RS-232 control port to test and measurement instruments that retain legacy computer interfaces. The +5 V-powered transceiver reduces the need for older ±12 V interface rails, and the dual-channel arrangement supports separate command and response connections. The -55°C to +125°C rating is suitable for broad industrial and mobile test platforms, while the CDIP package permits straightforward repair and retrofit. Route the cable-side traces as controlled pairs, minimize stubs, and place protection at the connector to preserve receiver reliability under external cable transients.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MAX232AMJE/883B — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MAX232AEPE+ | MAX232AMJE/883 | MAX232AMJE/883A |
|---|---|---|---|---|
| Package | 16-CDIP, 0.300-inch (7.62 mm) row spacing | 16-CDIP - same package family | 16-CDIP - same package family | 16-CDIP - same package family |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Transmitter Count | 2 drivers | 2 drivers | 2 drivers | 2 drivers |
| Receiver Count | 2 receivers | 2 receivers | 2 receivers | 2 receivers |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V |
| Interface Family | MAX232, +5 V RS-232 | MAX232, +5 V RS-232 | MAX232, +5 V RS-232 | MAX232, +5 V RS-232 |
| Supported Communications Standards | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 family support | EIA/TIA-232E and V.28/V.24 family support | EIA/TIA-232E and V.28/V.24 family support |
| Packing Method | Tube | Tube | Tube | Tube |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole |
| Qualification Designation | MAX232AMJE/883B | MAX232AEPE+ | MAX232AMJE/883 | MAX232AMJE/883A |
Diferensiator Kunci
- Broader documented environmental range (vsMAX232AEPE+)
- Exact qualified ordering revision (vsMAX232AMJE/883A)
- Two-channel transceiver integration (vsMAX232AMJE/883)
Catatan Desain
Use the Analog Devices MAX232 datasheet pin-description and charge-pump capacitor tables when assigning the 16-CDIP nets. Place the external capacitors close to their associated pins, use the shortest practical ground returns, and avoid routing RS-232 signals beneath or immediately beside the charge-pump circuitry. This minimizes switching-current coupling into the receive path and helps the transmitter and receiver retain predictable behavior in a two-channel interface.
Decouple the +5 V supply locally and verify the capacitor voltage rating against the charge-pump voltage conditions specified by the manufacturer. Keep the charge-pump traces compact because their switching current can create ground bounce. A single-point ground strategy near the IC, combined with a continuous chassis and signal-ground return to the connector, gives cable-connected equipment a lower-resistance reference than a fragmented board plane.
Do not treat every MAX232-family device as a mechanical substitute: the target uses a 16-CDIP footprint, while several MAX232 and MAX3232 products use SOIC or TSSOP packages. A proposed replacement must match the footprint, pin functions, electrical limits, temperature grade, and qualification document. For new compact designs, MAX3232CSE+ or MAX3232CUE+ may be appropriate functional choices, but they require a different PCB footprint and should not be called drop-in replacements for this target.
Protect external RS-232 connectors from electrostatic discharge and cable-borne transients. Place protection components near the connector boundary, and account for their capacitance and leakage when selecting them. Avoid long unprotected traces, especially on receiver inputs, and confirm the complete channel with a system-level loopback test across the intended cable length and environmental conditions.
Informasi Konformitas
The device is identified as military temperature grade, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was established.