Texas Instruments

MAX232INE4 - Dual RS-232 Driver/Receiver 120 kbps | Texas Instruments

MPN: MAX232INE4 ✓ Aktif
4.5 V to 5.5 V Vdss 16-pin PDIP Package
MOQ: 1 |

MAX232INE4 Ringkasan

Texas Instruments MAX232INE4 is a dual RS-232 driver and receiver interface IC with two driver channels, two receiver channels, a 120 kbps maximum data rate, and a 4.5 V to 5.5 V single supply, packaged in a 16-pin PDIP. The device includes an on-chip charge-pump voltage generator that produces the bipolar voltage levels required by TIA/EIA-232-F from one 5 V supply.

An RS-232 interface transceiver is an interface IC that converts low-voltage TTL or CMOS logic signals into RS-232 voltage levels and converts incoming RS-232 signals back into TTL or CMOS levels. Within the hierarchy of interface ICs, transceiver, communications interface, and voltage-level converter, the MAX232INE4 provides bidirectional signal conditioning for data terminals, computers, instrumentation, and embedded control equipment.

The device offers two drivers and two receivers in one package, allowing two serial channels to share the same integrated circuit. Its 120 kbps data rate is suitable for conventional asynchronous serial links operating below the RS-232 distance and capacitance limits of the installed cable. The 4.5 V to 5.5 V supply range supports regulated 5 V systems, while the charge pump eliminates the need for a separate negative supply.

According to the manufacturer datasheet, each receiver converts TIA/EIA-232-F inputs to 5 V TTL or CMOS levels, has a typical threshold of 1.3 V, provides typical hysteresis of 0.5 V, and can accept inputs up to plus or minus 30 V. The receiver architecture therefore combines useful noise immunity with protection from larger RS-232 transients. Each driver converts TTL or CMOS inputs into RS-232 levels, allowing the same package to support a complete point-to-point serial connection.

Typical uses include legacy RS-232 ports, industrial serial controllers, service equipment, data acquisition systems, and embedded systems communicating with computers or test instruments. Because the MAX232INE4 operates from a single 5 V rail, it integrates easily with conventional 5 V logic, although modern mixed-voltage systems may require level-shifting between 3.3 V controllers and the 5 V input threshold of this device.

When laying out the circuit, place the charge-pump capacitors and RS-232 interface protection components close to the device pins, and route protected RS-232 traces away from sensitive analog and clock signals. Confirm the driver and receiver logic levels, cable length, baud rate, and grounding arrangement before releasing the layout. For long cables or exposed industrial ports, add the surge and ESD protection appropriate to the installation environment.

This product page combines the manufacturer functional specifications, sourcing evidence, replacement cross-references, interface design guidance, and application-specific engineering considerations to support faster component selection and PCB implementation.

Alternatif penggantian untuk MAX232INE4 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian MAX232INE4 (sama faktor bentuk dan footprint) — berbeda di dalam Device Type, ESD Protection, Maximum Data Rate.

Texas Instruments
Device Type: Dual RS-232 driver/receiver
ESD Protection: ±2 kV
Maximum Data Rate: 120 kbit/s
Bandingkan dengan MAX232INE4 →
Texas Instruments
Device Type: Dual EIA-232 driver/receiver transceiver
ESD Protection: 8 mA typical; ±2 kV human-body-model ESD for the MAX232 family
Bandingkan dengan MAX232INE4 →

MAX232NE4

✅ Drop-In
Texas Instruments
📦 PDIP-16
Dual EIA-232 driver/receiver transceiver · 2 · 2 · 120 kbit/s · 4.5 V to 5.5 V · Single 5 V supply · 1.0 uF · ±30 V maximum

Kontak untuk harga

Lihat Datasheet →

MAX232N

✅ Drop-In
Texas Instruments
📦 PDIP-16
Dual RS-232 driver/receiver · 2 · 2 · 5 V · 120 kbit/s · ±9 V · ±30 V · 1.3 V

Kontak untuk harga

Lihat Datasheet →

MAX232INE4 Spesifikasi

Product Type Dual RS-232 driver/receiver interface IC
Driver Channels 2 drivers
Receiver Channels 2 receivers
Maximum Data Rate 120 kbps
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
Receiver Output Level 5 V TTL/CMOS
Receiver Typical Threshold 1.3 V
Receiver Typical Hysteresis 0.5 V
Maximum Receiver Input Voltage ±30 V
Charge-Pump Voltage Generator On-chip capacitive voltage generator
Interface Standard TIA/EIA-232-F
Paket 16-pin PDIP
Tipe Mounting Through-hole

MAX232INE4 16-pin pdip Diamant Konfigurasi Panduan

Konfigurasi pin untuk MAX232INE4 (16-pin pdip pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai 16-pin pdip untuk MAX232INE4

Tidak ada data diatribut pin yang tersedia untuk MAX232INE4.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

MAX232INE4 cocok untuk 6 aplikasis: Legacy Computer Serial Port, Industrial Serial Controller Interface, Data Acquisition Equipment, Embedded Service Console, Instrument Control and Test, Point-to-Point Communications Link.

🖥️

Legacy Computer Serial Port

The MAX232INE4 is suitable for a legacy RS-232 port because it combines two drivers, two receivers, a 120 kbps maximum data rate, and a single 5 V supply in one 16-pin PDIP. The driver channels translate 5 V TTL/CMOS commands into RS-232 levels, while the receiver channels return RS-232 responses as 5 V logic. Its on-chip charge-pump generates the required bipolar voltage levels, eliminating a separate negative supply. For equipment connected through a standard DB9 or terminal block, retain series resistors or network protection close to the connector and route the protected cable-side traces away from sensitive circuitry.

🏭

Industrial Serial Controller Interface

The MAX232INE4 fits industrial control and service interfaces that use RS-232 at rates up to 120 kbps. Two full driver/receiver sections allow one device to support two channels, reducing component count in multidrop or multiport equipment where full-duplex links are required. The 4.5 V to 5.5 V operating range accommodates regulated 5 V control electronics, and the receiver can accept ±30 V inputs as specified by the manufacturer datasheet. Industrial implementations should still add suitable transient protection at an exposed connector because the transceiver interface is not a substitute for a complete surge-protection network.

📊

Data Acquisition Equipment

The MAX232INE4 can connect laboratory and industrial data-acquisition equipment to a host computer through RS-232. Its 120 kbps rate supports moderate-rate command and measurement traffic without the complexity of a separate bipolar supply. The receiver threshold of 1.3 V and typical hysteresis of 0.5 V help distinguish valid signals amid noise. Use short, properly shielded cables, a common ground within the cable, and connector-side protection where the acquisition equipment may be exposed to long cables or hot-plugging. The logic interface should also be checked for compatibility with the host or controller voltage.

🔧

Embedded Service Console

The MAX232INE4 provides a straightforward path between a 5 V embedded controller and a technician's RS-232 service port. Two transmit channels can carry commands and status, while two receive channels can accept configuration responses or diagnostic data. A 120 kbps link is appropriate for setup menus, firmware-control interfaces, and short text protocols. Place the IC close to the connector's protection network, keep the charge-pump capacitor loop compact, and separate the protected RS-232 routing from clocks and analog inputs. If the controller operates at 3.3 V, add a bidirectional logic-level shifter before the MAX232 inputs and outputs.

📟

Instrument Control and Test

The MAX232INE4 is appropriate for RS-232 control ports on test and measurement instruments that exchange low-to-moderate-rate commands with a computer. The dual-driver, dual-receiver arrangement permits separate paths for instrument commands, responses, triggers, or status signals. Its 5 V supply and charge-pump implementation simplify instrumentation power design, while 120 kbps operation suits many automated test systems. Validate command timing, flow control, and cable capacitance at the selected baud rate, and add external protection for bench-top systems where users can connect unknown cable lengths or experience electrostatic discharge.

🌐

Point-to-Point Communications Link

The MAX232INE4 can establish a point-to-point RS-232 link between two pieces of equipment when both ends support RS-232 levels. Each side can use one driver for transmit and one receiver for receive, while the unused channels remain available. The 120 kbps maximum rate makes the device suitable for administrative, configuration, and low-bandwidth telemetry links rather than high-speed bulk transfer. Maintain a shared signal ground, use twisted-pair wiring where practical, and observe standard RS-232 polarity and connector conventions. The MAX232INE4 transceiver produces the required interface voltage levels but does not remove the need for cable and connector protection.

What are the key specifications of MAX232INE4 that engineers should know?
The MAX232INE4 is a dual RS-232 driver/receiver IC with two drivers, two receivers, a 120 kbps maximum data rate, a 4.5 V to 5.5 V supply range, and a 16-pin PDIP package. According to the Texas Instruments MAX232 datasheet, it uses an on-chip capacitive voltage generator to derive TIA/EIA-232-F voltage levels from a single 5 V supply. Each receiver converts RS-232 inputs to 5 V TTL/CMOS levels and can accept inputs up to ±30 V.
What is the operating voltage of MAX232INE4?
The MAX232INE4 operates from a single 4.5 V to 5.5 V supply, with 5 V as the nominal operating voltage. The Texas Instruments MAX232 datasheet identifies the part as a dual driver/receiver capable of producing TIA/EIA-232-F voltage levels from one 5 V supply. A regulated rail close to 5 V should therefore be used, while the charge-pump capacitors remain required for correct bipolar voltage generation.
What is the maximum data rate of MAX232INE4?
The MAX232INE4 supports a maximum data rate of 120 kbps. This rating comes from the Texas Instruments MAX232 datasheet and is adequate for many asynchronous RS-232 links, including service consoles and legacy peripheral interfaces. The usable rate in a complete system can also depend on cable length, capacitance, grounding, driver loading, and the protection components connected to the RS-232 pins.
Where can I download the MAX232INE4 datasheet PDF?
The official MAX232INE4 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/max232.pdf. The document describes the dual driver/receiver architecture, charge-pump voltage generator, receiver thresholds, electrical characteristics, and application information. Use the pin-description and typical application sections when assigning PCB nets and selecting the external charge-pump and interface capacitors.
Where can I find the MAX232INE4 pinout?
The MAX232INE4 pinout is shown in the Texas Instruments MAX232 datasheet at https://www.ti.com/lit/ds/symlink/max232.pdf. The device uses a 16-pin PDIP package with driver outputs, receiver inputs, charge-pump connections, supply pins, and ground pins. Use the pin-description table in the datasheet when making PCB assignments because connector-side RS-232 labels do not necessarily correspond to the internal IC pin names.
What is MAX232INE4 used for?
The MAX232INE4 is used to connect a 5 V TTL/CMOS controller or data terminal to an RS-232 port. It provides two driver channels for transmitting logic-level signals and two receiver channels for translating incoming RS-232 signals. According to the Texas Instruments MAX232 datasheet, the integrated capacitive voltage generator supplies the required bipolar interface levels from a single 5 V supply, making the device suitable for legacy serial ports and industrial RS-232 links.
Can MAX232INE4 operate from 3.3 V?
The MAX232INE4 is specified for a 4.5 V to 5.5 V supply and therefore does not operate directly from a 3.3 V rail. Its receiver outputs are specified as 5 V TTL/CMOS levels. If the connected controller operates at 3.3 V, use a suitable bidirectional level shifter on the logic-side connections and confirm that its direction, speed, and signal tolerances are appropriate for the selected UART baud rate.
What is the difference between MAX232INE4 and MAX232NE4?
The MAX232INE4 and MAX232NE4 are both 16-pin PDIP dual RS-232 transceivers associated with the same 120 kbps MAX232 interface family. The verified comparison information identifies MAX232NE4 as a tube-packed 16-pin PDIP device, while MAX232INE4 uses the INE4 ordering code. The meaningful selection checks are the manufacturer ordering suffix, temperature grade, packing method, and current lifecycle rather than the transceiver function itself.
Is MAX232INE4 the same as MAX232EINE4?
No. MAX232INE4 and MAX232EINE4 are related MAX232-family devices, but the E designation identifies the enhanced RS-232 family rather than the identical base MAX232 ordering code. The verified cross-reference results list MAX232EINE4 as a 16-pin PDIP transceiver, but the two devices should not be treated as automatically identical. Review the data rate, receiver thresholds, driver specifications, temperature range, and lifecycle status for the exact suffix before substitution.
When should I choose MAX232INE4 over MAX232NE4?
Choose MAX232INE4 when the exact industrial ordering code and 16-pin PDIP footprint match the PCB and the design requires the base MAX232 function at 120 kbps. Choose MAX232NE4 when its manufacturer ordering suffix, temperature grade, packing format, and lifecycle terms better fit the procurement plan. Since both occupy the same through-hole footprint, confirm the pin assignments and electrical ratings rather than selecting solely from package similarity.
What is the best drop-in replacement for MAX232INE4?
MAX232NE4 is the closest verified same-footprint drop-in candidate for MAX232INE4 because the comparison information identifies it as a 16-pin PDIP dual RS-232 transceiver with the same 120 kbps MAX232 family. Verify the exact temperature grade, pin configuration, and manufacturer ordering suffix before replacing the installed device. The verified cross-reference material did not establish enough qualifying pin-to-pin candidates for a larger drop-in list.
What can replace MAX232INE4?
MAX232NE4 can be considered as a same-package replacement candidate for MAX232INE4 because it is identified as a 16-pin PDIP MAX232 dual driver/receiver operating at the same stated 120 kbps data rate. The replacement must still be checked for operating-temperature grade, lifecycle status, and exact ordering suffix. Other MAX232 E-series devices may change data rate or receiver behavior and therefore are not automatically drop-in replacements.
Where to buy MAX232INE4 online?
Use the Request a Quote form on this page to request current MAX232INE4 availability, quantity breaks, and lead time. The component is a Texas Instruments 16-pin PDIP RS-232 interface IC rated for 120 kbps and a 4.5 V to 5.5 V supply. A quotation request allows the exact suffix and required packing format to be confirmed before an order is placed.
What is the price of MAX232INE4?
Use the Request a Quote form on this page for the current MAX232INE4 price, quantity tiers, stock position, and lead time. No fixed price is displayed because commercial terms can change with quantity, package format, and market conditions. The purchasing request should identify the exact MAX232INE4 ordering code, required quantity, and acceptable delivery schedule.
Is MAX232INE4 in stock and what is its lead time?
The Request a Quote form on this page is the channel for confirming current MAX232INE4 stock and lead time. The verified manufacturer and distributor references identify the 16-pin PDIP device, but they do not establish a fixed current inventory quantity or delivery schedule. Include your required quantity, target date, and preferred packing format when requesting the quotation.

Data referensi engineering untuk MAX232INE4 — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose MAX232INE4 for a 5 V system requiring two RS-232 driver/receiver channels, a maximum 120 kbps data rate, and the specific MAX232INE4 ordering code in a 16-pin PDIP footprint. MAX232NE4 is the closest verified same-footprint replacement candidate when its grade, packing format, temperature rating, and lifecycle terms satisfy the design; its stated 120 kbps interface rating matches the target. MAX232N is another verified 16-pin PDIP family candidate, but its exact electrical and temperature specifications must be checked before substitution. Do not automatically select MAX232E-series parts: the E designation identifies different enhanced-device characteristics, and the verified material does not establish that their data rates or receiver behavior remain within the required 30% drop-in limit.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini MAX232NE4 MAX232N
Package PDIP-16 PDIP-16 PDIP-16
Brand Texas Instruments Texas Instruments Texas Instruments
Product Function Dual RS-232 driver/receiver Dual RS-232 driver/receiver Dual RS-232 driver/receiver
Driver Channels 2 2 2
Receiver Channels 2 2 2
Interface Standard TIA/EIA-232-F RS-232 RS-232

Diferensiator Kunci

  • Two complete RS-232 channels in one device (vsMAX232NE4)
  • Single-supply RS-232 level generation (vsMAX232N)
  • Receiver input tolerance (vsMAX232N)

Catatan Desain

Place the charge-pump capacitors and the device close together on the PCB. Keep the capacitor connections short, use the capacitance and voltage ratings specified in the manufacturer datasheet, and avoid routing the charge-pump nodes beneath sensitive analog circuitry. Place the IC near the protected RS-232 connector so surge-current paths do not cross logic or ground-sensitive areas. Follow the pin-description table in the Texas Instruments MAX232 datasheet when assigning these nets.

Do not assume that every MAX232-family ordering code is a direct substitute. The MAX232E family can have different data-rate and receiver characteristics, while the N, IN, and NE4 suffixes can identify different grade or packing options. Before replacement, compare the supply range, data rate, receiver thresholds, temperature range, package pinout, and lifecycle status. The verified candidates in this page are limited to devices with a comparable 16-pin PDIP footprint.

For a 3.3 V controller, confirm that the 5 V TTL/CMOS receiver outputs are acceptable or add a suitable bidirectional level shifter on all logic-side signals. Account for directionality, propagation delay, and the selected UART rate. On the cable side, preserve the RS-232 ground connection and keep protected routes separated from clocks, ADC inputs, and other sensitive nodes.

Use the shortest practical connection between the IC and connector protection components. Route cable-side driver outputs away from receiver inputs when possible to reduce capacitive crosstalk, and terminate unused driver outputs as directed by the manufacturer application guidance. Avoid broad unprotected copper on external RS-232 nets because it increases capacitive loading and can contribute to emissions or ESD exposure.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The manufacturer datasheet and product references do not provide explicit compliance conclusions for this ordering code. Request current environmental and material compliance documentation from Texas Instruments before using the part in a regulated production program.

Pencarian Terkait

max232in datasheet MAX232INE4 datasheet MAX232INE4 datasheet pdf MAX232INE4 pinout MAX232INE4 specifications MAX232INE4 120 kbps MAX232INE4 PDIP-16 MAX232INE4 equivalent MAX232INE4 replacement MAX232INE4 vs MAX232NE4 Texas Instruments MAX232INE4 MAX232INE4 price MAX232INE4 stock MAX232INE4 RS-232 interface

Komponen dan Istilah Terkait

Texas Instruments MAX232INE4 MAX232NE4 MAX232N MAX232EINE4 RS-232 TIA/EIA-232-F dual driver/receiver transceiver interface IC communications interface IC voltage-level converter TTL CMOS charge-pump voltage generator PDIP-16 DIP package family through-hole package 120 kbps 4.5 V to 5.5 V RS-232 receiver threshold RS-232 driver embedded serial interface
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ