MAX232INE4 - Dual RS-232 Driver/Receiver 120 kbps | Texas Instruments
料号: MAX232INE4 ✓ 量产中MAX232INE4 概述
An RS-232 interface transceiver is an interface IC that converts low-voltage TTL or CMOS logic signals into RS-232 voltage levels and converts incoming RS-232 signals back into TTL or CMOS levels. Within the hierarchy of interface ICs, transceiver, communications interface, and voltage-level converter, the MAX232INE4 provides bidirectional signal conditioning for data terminals, computers, instrumentation, and embedded control equipment.
The device offers two drivers and two receivers in one package, allowing two serial channels to share the same integrated circuit. Its 120 kbps data rate is suitable for conventional asynchronous serial links operating below the RS-232 distance and capacitance limits of the installed cable. The 4.5 V to 5.5 V supply range supports regulated 5 V systems, while the charge pump eliminates the need for a separate negative supply.
According to the manufacturer datasheet, each receiver converts TIA/EIA-232-F inputs to 5 V TTL or CMOS levels, has a typical threshold of 1.3 V, provides typical hysteresis of 0.5 V, and can accept inputs up to plus or minus 30 V. The receiver architecture therefore combines useful noise immunity with protection from larger RS-232 transients. Each driver converts TTL or CMOS inputs into RS-232 levels, allowing the same package to support a complete point-to-point serial connection.
Typical uses include legacy RS-232 ports, industrial serial controllers, service equipment, data acquisition systems, and embedded systems communicating with computers or test instruments. Because the MAX232INE4 operates from a single 5 V rail, it integrates easily with conventional 5 V logic, although modern mixed-voltage systems may require level-shifting between 3.3 V controllers and the 5 V input threshold of this device.
When laying out the circuit, place the charge-pump capacitors and RS-232 interface protection components close to the device pins, and route protected RS-232 traces away from sensitive analog and clock signals. Confirm the driver and receiver logic levels, cable length, baud rate, and grounding arrangement before releasing the layout. For long cables or exposed industrial ports, add the surge and ESD protection appropriate to the installation environment.
This product page combines the manufacturer functional specifications, sourcing evidence, replacement cross-references, interface design guidance, and application-specific engineering considerations to support faster component selection and PCB implementation.
直接替换替代料: MAX232INE4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX232INE4 (相同外形与封装尺寸) ——差异在于 Device Type, ESD Protection, Maximum Data Rate.
MAX232INE4 规格参数
| Product Type | Dual RS-232 driver/receiver interface IC |
| Driver Channels | 2 drivers |
| Receiver Channels | 2 receivers |
| Maximum Data Rate | 120 kbps |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Receiver Output Level | 5 V TTL/CMOS |
| Receiver Typical Threshold | 1.3 V |
| Receiver Typical Hysteresis | 0.5 V |
| Maximum Receiver Input Voltage | ±30 V |
| Charge-Pump Voltage Generator | On-chip capacitive voltage generator |
| Interface Standard | TIA/EIA-232-F |
| 封装 | 16-pin PDIP |
| 安装类型 | Through-hole |
MAX232INE4 16-pin pdip 引脚配置指南
MAX232INE4(16-pin pdip 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX232INE4.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX232INE4 适用于 6 应用s: Legacy Computer Serial Port, Industrial Serial Controller Interface, Data Acquisition Equipment, Embedded Service Console, Instrument Control and Test, Point-to-Point Communications Link.
Legacy Computer Serial Port
The MAX232INE4 is suitable for a legacy RS-232 port because it combines two drivers, two receivers, a 120 kbps maximum data rate, and a single 5 V supply in one 16-pin PDIP. The driver channels translate 5 V TTL/CMOS commands into RS-232 levels, while the receiver channels return RS-232 responses as 5 V logic. Its on-chip charge-pump generates the required bipolar voltage levels, eliminating a separate negative supply. For equipment connected through a standard DB9 or terminal block, retain series resistors or network protection close to the connector and route the protected cable-side traces away from sensitive circuitry.
推荐
Industrial Serial Controller Interface
The MAX232INE4 fits industrial control and service interfaces that use RS-232 at rates up to 120 kbps. Two full driver/receiver sections allow one device to support two channels, reducing component count in multidrop or multiport equipment where full-duplex links are required. The 4.5 V to 5.5 V operating range accommodates regulated 5 V control electronics, and the receiver can accept ±30 V inputs as specified by the manufacturer datasheet. Industrial implementations should still add suitable transient protection at an exposed connector because the transceiver interface is not a substitute for a complete surge-protection network.
推荐
Data Acquisition Equipment
The MAX232INE4 can connect laboratory and industrial data-acquisition equipment to a host computer through RS-232. Its 120 kbps rate supports moderate-rate command and measurement traffic without the complexity of a separate bipolar supply. The receiver threshold of 1.3 V and typical hysteresis of 0.5 V help distinguish valid signals amid noise. Use short, properly shielded cables, a common ground within the cable, and connector-side protection where the acquisition equipment may be exposed to long cables or hot-plugging. The logic interface should also be checked for compatibility with the host or controller voltage.
推荐
Embedded Service Console
The MAX232INE4 provides a straightforward path between a 5 V embedded controller and a technician's RS-232 service port. Two transmit channels can carry commands and status, while two receive channels can accept configuration responses or diagnostic data. A 120 kbps link is appropriate for setup menus, firmware-control interfaces, and short text protocols. Place the IC close to the connector's protection network, keep the charge-pump capacitor loop compact, and separate the protected RS-232 routing from clocks and analog inputs. If the controller operates at 3.3 V, add a bidirectional logic-level shifter before the MAX232 inputs and outputs.
推荐
Instrument Control and Test
The MAX232INE4 is appropriate for RS-232 control ports on test and measurement instruments that exchange low-to-moderate-rate commands with a computer. The dual-driver, dual-receiver arrangement permits separate paths for instrument commands, responses, triggers, or status signals. Its 5 V supply and charge-pump implementation simplify instrumentation power design, while 120 kbps operation suits many automated test systems. Validate command timing, flow control, and cable capacitance at the selected baud rate, and add external protection for bench-top systems where users can connect unknown cable lengths or experience electrostatic discharge.
推荐
Point-to-Point Communications Link
The MAX232INE4 can establish a point-to-point RS-232 link between two pieces of equipment when both ends support RS-232 levels. Each side can use one driver for transmit and one receiver for receive, while the unused channels remain available. The 120 kbps maximum rate makes the device suitable for administrative, configuration, and low-bandwidth telemetry links rather than high-speed bulk transfer. Maintain a shared signal ground, use twisted-pair wiring where practical, and observe standard RS-232 polarity and connector conventions. The MAX232INE4 transceiver produces the required interface voltage levels but does not remove the need for cable and connector protection.
推荐
推荐产品汇总
工程参考数据: MAX232INE4 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX232NE4 | MAX232N |
|---|---|---|---|
| Package | PDIP-16 | PDIP-16 | PDIP-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Function | Dual RS-232 driver/receiver | Dual RS-232 driver/receiver | Dual RS-232 driver/receiver |
| Driver Channels | 2 | 2 | 2 |
| Receiver Channels | 2 | 2 | 2 |
| Interface Standard | TIA/EIA-232-F | RS-232 | RS-232 |
关键差异点
- Two complete RS-232 channels in one device (对比 MAX232NE4)
- Single-supply RS-232 level generation (对比 MAX232N)
- Receiver input tolerance (对比 MAX232N)
设计说明
Place the charge-pump capacitors and the device close together on the PCB. Keep the capacitor connections short, use the capacitance and voltage ratings specified in the manufacturer datasheet, and avoid routing the charge-pump nodes beneath sensitive analog circuitry. Place the IC near the protected RS-232 connector so surge-current paths do not cross logic or ground-sensitive areas. Follow the pin-description table in the Texas Instruments MAX232 datasheet when assigning these nets.
Do not assume that every MAX232-family ordering code is a direct substitute. The MAX232E family can have different data-rate and receiver characteristics, while the N, IN, and NE4 suffixes can identify different grade or packing options. Before replacement, compare the supply range, data rate, receiver thresholds, temperature range, package pinout, and lifecycle status. The verified candidates in this page are limited to devices with a comparable 16-pin PDIP footprint.
For a 3.3 V controller, confirm that the 5 V TTL/CMOS receiver outputs are acceptable or add a suitable bidirectional level shifter on all logic-side signals. Account for directionality, propagation delay, and the selected UART rate. On the cable side, preserve the RS-232 ground connection and keep protected routes separated from clocks, ADC inputs, and other sensitive nodes.
Use the shortest practical connection between the IC and connector protection components. Route cable-side driver outputs away from receiver inputs when possible to reduce capacitive crosstalk, and terminate unused driver outputs as directed by the manufacturer application guidance. Avoid broad unprotected copper on external RS-232 nets because it increases capacitive loading and can contribute to emissions or ESD exposure.
合规信息
The manufacturer datasheet and product references do not provide explicit compliance conclusions for this ordering code. Request current environmental and material compliance documentation from Texas Instruments before using the part in a regulated production program.