MAX3243CUI+T - 3/5 250kbps RS-232 Transceiver | Analog Devices
MPN: MAX3243CUI+T ✓ AktifMAX3243CUI+T Ringkasan
An RS-232 transceiver is an interface integrated circuit that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into digital logic. The MAX3243 belongs to the transceiver family within the broader hierarchy of interface ICs, communication semiconductors, and integrated circuits. It is particularly useful where several serial ports share a limited connector or enclosure and low supply current is important.
Key features include three RS-232 drivers, five RS-232 receivers, 3 V to 5.5 V operation, and data rates up to 250 kbps. AutoShutdown circuitry detects whether valid receiver activity is present and disables the on-board supply and drivers when the port is inactive. The manufacturer describes a supply current as low as 1 µA during shutdown, making the device suitable for power-conscious embedded and portable equipment. A complementary always-active receiver supports external monitoring in selected applications.
The MAX3243 supports both 3.3 V and 5 V system rails. This operating range permits the same transceiver to interface with modern low-voltage CMOS controllers as well as established 5 V logic. Its integrated charge-pump circuitry supports the positive and negative RS-232 voltage levels required by the interface standard, while the ±15 kV ESD rating strengthens protection against cable-connected electrostatic discharge events.
Typical uses include industrial control systems, serial-port adapters, test equipment, point-of-sale terminals, data-acquisition equipment, and embedded console interfaces. In a multiport installation, the three drivers can support three outbound channels while five receivers provide inbound monitoring. Designers should nevertheless confirm the required channel direction, electrical standard, connector protection, and system grounding for each cable interface.
For layout, place the device close to the connector and route RS-232 traces away from clocks, switching nodes, and sensitive analog inputs. Keep the transmit and receive paths arranged to minimize differential crosstalk, follow the manufacturer’s recommended charge-pump capacitor connections, and provide local supply bypassing. The ±15 kV rating is a device-level specification and does not replace appropriate cable, connector, and board-level protection.
This page combines the MAX3243 family specifications, verified ordering information, same-footprint alternatives, and practical interface-design guidance. It also distinguishes confirmed drop-in candidates from alternatives that require pinout and signal-direction review before use in an existing 28-pin TSSOP design.
Alternatif penggantian untuk MAX3243CUI+T — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MAX3243CUI+T (sama faktor bentuk dan footprint) — berbeda di dalam Product Type, Package, Supply Voltage Range, Number of Drivers, Number of Receivers.
MAX3243EUI+T
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX3243CAI+T
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MAX3243CUI+
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX3232EEUE+T
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX3232CUE+T
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX3243CUI+T Spesifikasi
| Product Type | 3-driver, 5-receiver RS-232 transceiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Driver Count | 3 |
| Receiver Count | 5 |
| Duplex Mode | Full duplex |
| ESD Protection | ±15 kV |
| Shutdown Supply Current | 1 µA |
| Low-Voltage Operation | 3.3 V compatible |
| Paket | TSSOP-28 |
| Tipe Mounting | Surface mount |
| Power Management Feature | AutoShutdown |
| Always-Active Receiver | Complementary always-active receiver |
| Status Lingkungan Hidup | Active |
MAX3243CUI+T tssop-28 Diamant Konfigurasi Panduan
Konfigurasi pin untuk MAX3243CUI+T (tssop-28 pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk MAX3243CUI+T.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MAX3243CUI+T cocok untuk 6 aplikasis: Industrial Serial Control Interface, Multiport Serial Adapter, Test and Measurement Equipment, Point-of-Sale Terminal, Data Acquisition Equipment, Embedded Console and Debug Port.
Industrial Serial Control Interface
The MAX3243CUI+T fits industrial equipment that requires several RS-232 channels without allocating separate interface ICs. Its three drivers and five receivers support three outbound control paths and multiple inbound status-monitoring paths, while 3 V to 5.5 V operation accommodates both legacy 5 V controllers and modern 3.3 V embedded processors. The 250 kbps maximum data rate is suitable for configuration links, service ports, and supervisory communication. The ±15 kV ESD rating adds useful device-level protection on exposed serial connectors, although it does not eliminate the need for a suitable cable shield, chassis grounding, and connector selection.
Direkomendasikan
Multiport Serial Adapter
A multiport serial adapter can use the MAX3243CUI+T to consolidate several communication channels into a compact controller board. Three RS-232 drivers handle outbound traffic, while five receivers provide additional inputs for monitoring, status, or handshake signals. The 28-pin TSSOP package supports dense equipment layouts, and the 3 V to 5.5 V supply range simplifies adaptation across different embedded platforms. AutoShutdown is valuable in adapters that remain connected but transmit intermittently because the device can reduce supply current to 1 µA when no valid receiver activity is detected.
Direkomendasikan
Test and Measurement Equipment
The MAX3243CUI+T is appropriate for test and measurement instruments that expose RS-232 command, trigger, or status interfaces to a host computer. Its five receivers permit several status or acknowledgment lines to be observed, while three drivers support outbound command channels. Operation from 3 V to 5.5 V lets the transceiver coexist with modern test-controller logic, and the 250 kbps rate is suitable for many legacy serial-control protocols. Layout should keep the RS-232 traces away from high-impedance analog inputs and switching nodes to reduce coupling into measurement results.
Direkomendasikan
Point-of-Sale Terminal
Point-of-sale terminals often combine service-port communication with peripheral status lines, making the MAX3243CUI+T’s three transmitters and five receivers practical. The interface can support printer, display, scanner, or service connections when the channel directions match the system architecture. Its ability to operate from 3.3 V or 5 V supports both embedded Linux-class controllers and legacy terminal electronics. Because external cables can carry electrostatic discharge toward the equipment, the interface should be paired with appropriate connector grounding and system-level surge protection in addition to the device’s ±15 kV ESD rating.
Direkomendasikan
Data Acquisition Equipment
Data-acquisition equipment can use the MAX3243CUI+T for configuration and supervisory links between a host and remote measurement hardware. Five receiver channels provide room for command acknowledgments, module-status indicators, or multi-axis control signals, while three drivers support outbound requests. The 250 kbps limit is well suited to many configuration protocols and short control exchanges rather than continuous high-bandwidth transfer. Place the transceiver near the serial connector and isolate its return path from sensitive measurement inputs to prevent common-impedance and radiated-noise coupling into the acquisition section.
Direkomendasikan
Embedded Console and Debug Port
The MAX3243CUI+T can support an embedded console, maintenance port, or debug interface in industrial and communications equipment. Three drivers allow the host to address multiple downstream devices, while five receivers can collect acknowledgments, reset requests, or configuration responses. AutoShutdown helps minimize consumption when the console cable is absent, and 3 V to 5.5 V operation allows use with a broad range of embedded processors. Designers should preserve the device’s recommended charge-pump capacitor placement and keep connector-side traces physically separated from sensitive clock and high-speed digital routes.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MAX3243CUI+T — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MAX3243EUI+T | MAX3243CAI+T | MAX3243CUI+ | MAX3232EEUE+T | MAX3232CUE+T |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | TSSOP-28 | TSSOP-28 | SSOP-28 | TSSOP-28 | TSSOP-28 | TSSOP-28 |
| Interface Standard | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 |
Diferensiator Kunci
- Broader channel count within the MAX3243 family (vsMAX3232EEUE+T)
- Higher documented family data rate (vsMAX3243EUI+T)
- Automatic low-power behavior for intermittent links (vsMAX3232CUE+T)
Catatan Desain
Place the MAX3243CUI+T close to the RS-232 connector and route driver outputs directly toward the protected connector pins. Keep receiver inputs away from switching-node and high-current traces to reduce common-mode coupling. Follow the manufacturer’s charge-pump capacitor configuration exactly because incorrect capacitor placement can increase radiated noise, reduce startup margin, or impair voltage generation.
Treat the three transmit channels as potential EMI sources because RS-232 transitions can have steep edges even at modest data rates. Route each transmit pair together, maintain a continuous ground reference where appropriate, and avoid sharing narrow return paths with analog or digital signal nets. A cable shield connected according to the equipment’s grounding strategy can reduce common-mode noise entering the enclosure.
Provide local supply decoupling at the MAX3243CUI+T and keep the power and ground connections short to the device. The 3 V to 5.5 V operating range supports both 3.3 V and 5 V rails, but the host logic and charge-pump requirements must remain within the manufacturer’s operating conditions. Verify startup and shutdown behavior when the system rail can collapse before the serial connector is disconnected.
Do not assume that every 28-pin RS-232 transceiver has the same channel arrangement. The MAX3243 provides three drivers and five receivers, whereas MAX3232-family devices use different configurations. Before substituting a part, compare every driver, receiver, supply, ground, charge-pump, and enable-related connection in the manufacturer pin-description tables and confirm the package dimensions against the PCB land pattern.
Informasi Konformitas
The family is an RS-232 interface IC rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer’s current compliance documentation.