Analog Devices

MAX393EPE - Quad SPST Analog Switch | Analog Devices

MPN: MAX393EPE ✓ Aktif
+3 V to +15 V Vdss 20 Ω typical Rds(on) 16-pin DIP Package
MOQ: 1 |

MAX393EPE Ringkasan

The Analog Devices MAX393EPE is a precision, quad, single-pole single-throw analog switch with a typical low on-resistance of 20 Ω, guaranteed on-resistance matching below 2 Ω, and guaranteed on-resistance flatness below 2 Ω across the signal range. The device is packaged in a 16-pin through-hole DIP and supports single-supply operation from +3 V to +15 V or bipolar operation from ±3 V to ±8 V.

An analog switch is an electronically controlled semiconductor interconnect that routes a signal between circuit nodes while providing high impedance in its open state. The MAX393 belongs to the analog-switch hierarchy within interface ICs. Its four independent SPST switches are intended for precision signal routing where low channel-to-channel resistance variation, controlled charge injection, low leakage, and low power consumption are important.

Key electrical characteristics include a typical on-resistance of 20 Ω, on-resistance matching below 2 Ω, on-resistance flatness below 2 Ω, and power consumption below 1 µW. The Analog Devices MAX393 product page lists single-supply operation over +3 V to +15 V, bipolar operation over ±3 V to ±8 V, and electrostatic-discharge withstand above 2000 V per Method 3015.7. These characteristics distinguish the device from higher-resistance general-purpose switch arrays.

The four switches are designed to preserve signal integrity when a system changes source or measurement paths. Tight on-resistance matching limits gain or attenuation differences between channels, while flat on-resistance reduces signal-dependent distortion as the analog input changes. The MAX393EPE uses a 16-pin DIP package for through-hole assembly, providing ample spacing between pins and straightforward socket or PCB mounting in laboratory and industrial equipment.

Typical uses include precision test and measurement systems, data-acquisition input networks, industrial instrumentation, sample-and-hold circuits, and controlled analog-signal routing. The part can operate from a single positive supply or from split bipolar rails, allowing it to fit both compact single-supply designs and instrumentation with bipolar signal ranges. Its low power consumption is especially useful when the switched signals are not continuously active.

A critical design consideration is to keep control-signal transitions away from sensitive analog traces because charge injection can create a temporary output disturbance when a switch changes state. Confirm that the selected supply configuration, input voltage, control logic level, and signal amplitude satisfy the MAX393 absolute-maximum and operating limits in the manufacturer data sheet before finalizing the circuit.

This page combines the manufacturer’s MAX393 electrical characteristics with package details, practical routing guidance, application analysis, and same-package replacement considerations. It is structured to help engineers evaluate the MAX393EPE for precision analog switching without relying on a generic catalog summary.

Alternatif penggantian untuk MAX393EPE — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

MAX393CPE

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 16-pin DIP
Uses the C temperature designation rather than the E designation of MAX393EPE; electrical core is the MAX393 family, but the temperature limits must be compared before use.

📋 Alternatif referensi (tidak dalam katalog)

MAX393EUE

✅ Drop-In
📦 16-pin DIP
Same MAX393 precision SPST family and 16-pin DIP outline, with a different ordering suffix that changes the package or temperature classification.

📋 Alternatif referensi (tidak dalam katalog)

MAX393ESE

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 16-pin DIP
Same four-channel SPST switching architecture and 16-pin DIP footprint; ordering code differs from MAX393EPE, so temperature and package metadata require confirmation.

📋 Alternatif referensi (tidak dalam katalog)

MAX393EAA

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 16-pin DIP
Same MAX393 family and DIP package class, but the ordering suffix denotes a different package or temperature classification from MAX393EPE.

📋 Alternatif referensi (tidak dalam katalog)

MAX393CUE

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 16-pin DIP
Shares the MAX393 four-SPST architecture and 16-pin DIP outline while using a different temperature and ordering-code combination from MAX393EPE.

📋 Alternatif referensi (tidak dalam katalog)

MAX393EPE Rating Maksimal & Karakteristik Listrik

Product Type Precision quad SPST analog switch
Number of Switches 4 switches
Switch Configuration 4 independent SPST switches
On-Resistance 20 Ω typical
On-Resistance Matching Between Channels <2 Ω guaranteed
On-Resistance Flatness Over Signal Range <2 Ω guaranteed
Single-Supply Operating Range +3 V to +15 V
Bipolar-Supply Operating Range ±3 V to ±8 V
Power Consumption <1 µW
Electrostatic Discharge Withstand >2000 V per Method 3015.7
Paket 16-pin DIP
Tipe Mounting Through-hole
Temperature Grade Industrial
Production Status Production

MAX393EPE 16-pin dip Diamant Konfigurasi Panduan

Konfigurasi pin untuk MAX393EPE (16-pin dip pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai 16-pin dip untuk MAX393EPE

Tidak ada data diatribut pin yang tersedia untuk MAX393EPE.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

MAX393EPE cocok untuk 6 aplikasis: Precision Test and Measurement, Data Acquisition Input Multiplexing, Industrial Instrumentation, Sample-and-Hold Signal Routing, Laboratory Automation, Bipolar Sensor Interface.

🖥️

Precision Test and Measurement

The MAX393EPE fits precision test and measurement systems that route multiple low-frequency signals through one instrument front end. Its four SPST switches provide independent path selection, while guaranteed on-resistance matching below 2 Ω and flatness below 2 Ω reduce channel-dependent amplitude errors. A typical implementation places switched sources, reference inputs, or guard signals on the instrument PCB and drives each control line from the measurement controller. The 16-pin DIP format supports through-hole sockets and conventional laboratory-card construction. Designers should still verify input bandwidth, charge injection, leakage, and control timing for the specific signal amplitude and measurement bandwidth.

📡

Data Acquisition Input Multiplexing

The MAX393EPE is suitable for controlled signal selection in a data-acquisition input network. Its typical on-resistance of 20 Ω can be used to connect sensor or reference channels to a shared analog front end when signal bandwidth and source impedance are compatible with that resistance. Matching below 2 Ω between channels helps limit gain imbalance, while flatness below 2 Ω reduces output variation across the signal range. The device may be placed between a terminal board and the analog measurement circuitry. High-impedance sensors can require additional buffering because switch on-resistance, capacitance, leakage, and injected charge all influence measurement accuracy.

🏭

Industrial Instrumentation

The MAX393EPE supports analog routing in industrial instrumentation that must operate from a single supply or bipolar rails. Its +3 V to +15 V single-supply range accommodates compact control systems, while ±3 V to ±8 V operation suits instrumentation handling signals around ground. Four independent switches can isolate sensors, select filters, or connect calibration references without adding continuous relay drive power. The below-1 µW power-consumption figure is useful in continuously powered equipment. Industrial designs must still account for the actual operating-temperature grade, transient protection, ground-loop behavior, and the control levels required by the surrounding controller.

⚡

Sample-and-Hold Signal Routing

The MAX393EPE can route sampling-related signals where four independently selected paths must be controlled by digital logic. Its precision SPST arrangement allows a hold capacitor, acquisition source, reference, and reset path to be connected selectively, subject to the data sheet’s switching-time and charge-injection limits. Low on-resistance variation helps maintain consistent settling behavior among channels, while the compact 16-pin DIP supports straightforward through-hole implementation. In practical sample-and-hold circuits, the control edge should occur while the acquisition path is no longer sensitive to injected charge, and the capacitor’s dielectric absorption and leakage should be evaluated separately.

🔧

Laboratory Automation

The MAX393EPE is appropriate for laboratory automation equipment that repeatedly routes analog signals between instruments, sensors, and reference sources. Four SPST switches reduce the number of discrete routing elements required for a basic analog matrix, and the 16-pin DIP package is convenient for socketed or hand-built control cards. The guaranteed matching and flatness characteristics help maintain repeatability when different channels are selected. Because each transition can create a temporary output disturbance through charge injection, acquisition systems should blank or reject samples during switching. Control traces should also be kept away from sensitive analog nodes to minimize capacitive coupling.

📱

Bipolar Sensor Interface

The MAX393EPE can interface bipolar sensors when the system uses split supplies from ±3 V to ±8 V. Each SPST switch may connect a positive, negative, or reference-sensing path to a common conditioning channel while the common-mode voltage remains within the device operating limits. Matching below 2 Ω and on-resistance flatness below 2 Ω help preserve channel consistency across changing sensor voltages. The low-power switching characteristic is favorable for portable or continuously monitored instrumentation. Designers should verify absolute-maximum input voltage, off-state leakage, control-signal polarity, and whether the sensor source impedance makes the switch resistance significant relative to the required measurement accuracy.

Ringkasan Produk Direkomendasikan

MAX393EPE Analog Devices Digunakan di dalam: Precision Test and Measurement, Data Acquisition Input Multiplexing, Industrial Instrumentation, Sample-and-Hold Signal Routing, Laboratory Automation, Bipolar Sensor Interface MAX393 Parent precision analog-switch family Digunakan di dalam: Precision Test and Measurement, Sample-and-Hold Signal Routing MAX393EUE Same-family switching-array option Digunakan di dalam: Data Acquisition Input Multiplexing, Laboratory Automation MAX393CPE Same-family lower-temperature ordering option Digunakan di dalam: Industrial Instrumentation MAX393ESE Same-family DIP switching variant Digunakan di dalam: Bipolar Sensor Interface
What is the MAX393EPE and what does it do?
The MAX393EPE is a precision quad SPST analog switch from Analog Devices, with four independent normally open switches in a 16-pin DIP package. According to the Analog Devices MAX393 data sheet, Revision 3, each switch has a typical on-resistance of 20 Ω, while guaranteed matching between channels and flatness over the signal range are each below 2 Ω. It is intended for controlled routing of low-frequency precision analog signals.
What is the on-resistance of the MAX393EPE?
The MAX393EPE has a typical on-resistance of 20 Ω when the switch is closed. The Analog Devices MAX393 product page also identifies guaranteed on-resistance matching below 2 Ω and guaranteed on-resistance flatness below 2 Ω across the signal range. These guarantees are more useful than the typical value alone when matching multiple channels or preserving signal amplitude across a changing input voltage.
What supply voltages can the MAX393EPE use?
The MAX393EPE supports single-supply operation from +3 V to +15 V and bipolar operation from ±3 V to ±8 V. These ranges appear in the Analog Devices MAX393 product information. The correct choice depends on the control-signal levels and whether the switched signal is referenced to ground or can swing above and below ground. Logic levels and maximum input voltage must remain within the data-sheet limits.
Is the MAX393EPE suitable for precision test equipment?
The MAX393EPE is suitable for precision test-equipment signal paths because its 20 Ω typical on-resistance is paired with guaranteed channel matching below 2 Ω and flatness below 2 Ω. These characteristics help limit channel-dependent gain errors. The 16-pin DIP package also supports conventional through-hole assembly in laboratory instruments, automated test systems, and industrial measurement equipment.
What package does the MAX393EPE use?
The MAX393EPE uses a 16-pin DIP package intended for through-hole mounting. The package information shown for MAX393EPE identifies a rectangular DIP with 16 terminals and non-surface-mount construction. Its widely spaced pins support straightforward PCB or socket assembly and reduce the mechanical complexity associated with fine-pitch surface-mount switching devices.
Where can I download the MAX393EPE datasheet PDF?
The official MAX393EPE technical information is available from the Analog Devices MAX393 product page, which links to the manufacturer data sheet. The data sheet is identified as Revision 3 and contains the pin configuration, electrical characteristics, operating conditions, and application details needed for circuit design. Use the manufacturer document for authoritative pin numbering and maximum ratings.
Where can I find the MAX393EPE pinout?
The MAX393EPE pin configuration is published in the pin-description and ordering-information sections of the Analog Devices MAX393 data sheet, Revision 3. Because a complete pin map is not reproduced on this page, assign PCB connections directly from that table. The target uses a 16-pin DIP outline, and each control and switched-terminal connection should be checked against the selected package variant.
What can replace the MAX393EPE?
A valid replacement for the MAX393EPE must use the same 16-pin DIP footprint, provide four compatible SPST switches, and maintain comparable on-resistance, matching, flatness, leakage, supply range, and control levels. No manufacturer-published universal replacement list identifies five guaranteed drop-in substitutes. Same-family MAX393 variants can be evaluated for temperature and ordering-code differences, but the data sheet must be checked before any substitution is approved.
Is the MAX393EPE the same as the MAX393EUE?
The MAX393EPE and MAX393EUE belong to the same MAX393 precision analog-switch family, but their ordering suffixes can identify different package or temperature classifications. They should be treated as interchangeable only after confirming the 16-pin DIP footprint, pin functions, electrical limits, temperature grade, and lead requirements in the manufacturer documentation. A shared family name alone does not establish drop-in compatibility.
MAX393EPE vs MAX393EUE: which is better for industrial equipment?
The MAX393EPE vs MAX393EUE decision depends primarily on the exact package and temperature ordering codes, not on the underlying switching function. The MAX393 family provides four precision SPST switches with a typical on-resistance of 20 Ω. For industrial equipment, confirm that the candidate offers the required operating-temperature grade and that its 16-pin DIP dimensions, pin numbering, and lead finish match the existing PCB.
When should I choose the MAX393EPE over another analog switch?
Choose the MAX393EPE when a design needs four independently controlled SPST analog switches, low channel-to-channel resistance variation, and a through-hole 16-pin DIP implementation. It is particularly suitable when signals are referenced to either a single positive rail or bipolar rails and power consumption below 1 µW is useful. A lower-cost or surface-mount alternative is preferable only when the complete electrical specification permits.
Is the MAX393EPE suitable for data-acquisition and instrumentation systems?
The MAX393EPE is suitable for data-acquisition and instrumentation systems requiring four independently switched precision analog paths. Its guaranteed on-resistance matching below 2 Ω and flatness below 2 Ω help reduce measurement error between channels, while the 20 Ω typical resistance is modest for many low-frequency sensor and test signals. Bandwidth, injection error, leakage, and control timing still require application-level verification.
What is the lead time for the MAX393EPE?
Current lead time and minimum order quantity should be requested through the Request a Quote form on this page. The Analog Devices product page identifies MAX393 as production, but production status does not establish current allocation, package availability, or delivery timing. Include the exact MAX393EPE ordering code and required quantity when requesting the commercial schedule.
Is the MAX393EPE in stock?
Current MAX393EPE inventory should be confirmed through the Request a Quote form on this page. The Analog Devices MAX393 page identifies the family as production, while distributor availability can vary by package, quantity, and region. Submit the exact MPN and required quantity to obtain the latest allocation, lead time, and shipment information rather than relying on a stale catalog status.
How much does the MAX393EPE cost?
Use the Request a Quote form on this page for the current MAX393EPE unit price and quantity breaks. Commercial pricing depends on the exact ordering code, package, order quantity, and current market conditions. The manufacturer page includes family-level list-price information, but a live quote provides the correct value for this specific MAX393EPE configuration.
What are the key specifications engineers should know about MAX393EPE?
The key MAX393EPE specifications are four precision SPST switches, 20 Ω typical on-resistance, less than 2 Ω guaranteed channel matching, less than 2 Ω guaranteed on-resistance flatness, +3 V to +15 V single-supply operation, ±3 V to ±8 V bipolar operation, and less than 1 µW power consumption. The device is offered in a 16-pin through-hole DIP with an industrial temperature-grade designation.

Data referensi engineering untuk MAX393EPE — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the MAX393EPE when the PCB requires four precision SPST switches in a 16-pin DIP outline and the design benefits from guaranteed on-resistance matching below 2 Ω, flatness below 2 Ω, and typical on-resistance of 20 Ω. It supports both +3 V to +15 V single-supply operation and ±3 V to ±8 V bipolar operation, making it appropriate for laboratory instruments, industrial measurement systems, data-acquisition interfaces, and controlled signal-routing circuits. Same-family ordering variants such as MAX393CPE, MAX393EUE, MAX393ESE, MAX393EAA, and MAX393CUE may preserve the basic switching architecture and package class, but temperature grade, package construction, and exact limits must be confirmed before use. Choose the MAX393EPE instead of a generic switch array when channel matching, resistance flatness, low power, and through-hole assembly are central requirements.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini MAX393CPE MAX393EUE MAX393ESE MAX393EAA MAX393CUE
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 16-pin DIP 16-pin DIP 16-pin DIP 16-pin DIP 16-pin DIP 16-pin DIP
Number of Switches 4 4 4 4 4 4
Switch Configuration Quad SPST Quad SPST Quad SPST Quad SPST Quad SPST Quad SPST

Diferensiator Kunci

  • Guaranteed channel matching supports consistent precision measurements (vsMAX393CPE)
  • Low on-resistance flatness reduces signal-dependent amplitude variation (vsMAX393EUE)
  • Supports both compact single-supply and bipolar instrumentation designs (vsMAX393ESE)
  • Low power consumption suits continuously powered analog routing (vsMAX393EAA)

Catatan Desain

Treat charge injection as a sampling-timing issue rather than only a DC offset issue. When a control line changes state, the transition can produce a temporary voltage disturbance at the switched output. If the downstream amplifier samples immediately, allow the output to settle or blank the sample during the transition. Keep switching-control traces away from sensitive input and output nodes, and use a ground reference close to the device to reduce coupling into high-impedance measurement paths.

Route the analog switched paths as short and direct as practical, with a continuous ground plane and minimal stub branches. The MAX393EPE uses a through-hole DIP footprint, so component placement can reduce parasitic capacitance compared with a dense surface-mount layout. Avoid placing high-current or fast-switching traces adjacent to the switched nodes. Maintain the clearances required for the selected switching voltage and installed package.

Do not assume that all MAX393 ordering codes are automatically interchangeable. Confirm the package dimensions, lead finish, pin numbering, temperature grade, absolute-maximum ratings, and control-input thresholds for every candidate. The MAX393EPE is a 16-pin DIP part, and the MAX393 family’s suffix changes can indicate meaningful differences. A physical fit alone does not prove electrical or environmental equivalence.

Select the supply arrangement from the actual signal range: +3 V to +15 V for single-supply use or ±3 V to ±8 V for bipolar operation. Ensure that control levels remain valid in the chosen configuration and that all switched input and output voltages stay within the absolute-maximum limits. The below-1 µW power-consumption specification should not be interpreted as total system consumption because control-driver current and off-state leakage also contribute.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The industrial temperature designation does not by itself imply AEC-Q100 qualification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established by the cited product information.

Data disahkan pada: 2026-11-19 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

MAX393EPE datasheet MAX393EPE pinout MAX393EPE datasheet pdf MAX393EPE specifications MAX393EPE equivalent MAX393EPE replacement MAX393EPE cross reference MAX393EPE vs MAX393EUE MAX393EPE 16 pin DIP MAX393EPE price Analog Devices MAX393EPE MAX393EPE precision analog switch

Komponen dan Istilah Terkait

Analog Devices MAX393EPE MAX393 MAX393CPE MAX393EUE MAX393ESE MAX393EAA MAX393CUE precision analog switch SPST switch quad analog switch analog switch IC interface IC semiconductor 16-pin DIP through-hole package on-resistance on-resistance matching on-resistance flatness charge injection single-supply operation bipolar-supply operation industrial instrumentation data acquisition test and measurement
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ