MAX393EPE - Quad SPST Analog Switch | Analog Devices
MPN: MAX393EPE ✓ 啟用中MAX393EPE 概覽
An analog switch is an electronically controlled semiconductor interconnect that routes a signal between circuit nodes while providing high impedance in its open state. The MAX393 belongs to the analog-switch hierarchy within interface ICs. Its four independent SPST switches are intended for precision signal routing where low channel-to-channel resistance variation, controlled charge injection, low leakage, and low power consumption are important.
Key electrical characteristics include a typical on-resistance of 20 Ω, on-resistance matching below 2 Ω, on-resistance flatness below 2 Ω, and power consumption below 1 µW. The Analog Devices MAX393 product page lists single-supply operation over +3 V to +15 V, bipolar operation over ±3 V to ±8 V, and electrostatic-discharge withstand above 2000 V per Method 3015.7. These characteristics distinguish the device from higher-resistance general-purpose switch arrays.
The four switches are designed to preserve signal integrity when a system changes source or measurement paths. Tight on-resistance matching limits gain or attenuation differences between channels, while flat on-resistance reduces signal-dependent distortion as the analog input changes. The MAX393EPE uses a 16-pin DIP package for through-hole assembly, providing ample spacing between pins and straightforward socket or PCB mounting in laboratory and industrial equipment.
Typical uses include precision test and measurement systems, data-acquisition input networks, industrial instrumentation, sample-and-hold circuits, and controlled analog-signal routing. The part can operate from a single positive supply or from split bipolar rails, allowing it to fit both compact single-supply designs and instrumentation with bipolar signal ranges. Its low power consumption is especially useful when the switched signals are not continuously active.
A critical design consideration is to keep control-signal transitions away from sensitive analog traces because charge injection can create a temporary output disturbance when a switch changes state. Confirm that the selected supply configuration, input voltage, control logic level, and signal amplitude satisfy the MAX393 absolute-maximum and operating limits in the manufacturer data sheet before finalizing the circuit.
This page combines the manufacturer’s MAX393 electrical characteristics with package details, practical routing guidance, application analysis, and same-package replacement considerations. It is structured to help engineers evaluate the MAX393EPE for precision analog switching without relying on a generic catalog summary.
直接替換替代品,適用於 MAX393EPE — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MAX393CPE
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX393EUE
✅ 直接替換📋 參考替代品(不在目錄中)
MAX393ESE
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX393EAA
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX393CUE
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX393EPE 最大額定值與電氣特性
| Product Type | Precision quad SPST analog switch |
| Number of Switches | 4 switches |
| Switch Configuration | 4 independent SPST switches |
| On-Resistance | 20 Ω typical |
| On-Resistance Matching Between Channels | <2 Ω guaranteed |
| On-Resistance Flatness Over Signal Range | <2 Ω guaranteed |
| Single-Supply Operating Range | +3 V to +15 V |
| Bipolar-Supply Operating Range | ±3 V to ±8 V |
| Power Consumption | <1 µW |
| Electrostatic Discharge Withstand | >2000 V per Method 3015.7 |
| 封裝 | 16-pin DIP |
| 安裝類型 | Through-hole |
| Temperature Grade | Industrial |
| Production Status | Production |
MAX393EPE 16-pin dip 腳位配置指南
MAX393EPE(16-pin dip 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX393EPE.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX393EPE 適用於 6 應用s: Precision Test and Measurement, Data Acquisition Input Multiplexing, Industrial Instrumentation, Sample-and-Hold Signal Routing, Laboratory Automation, Bipolar Sensor Interface.
Precision Test and Measurement
The MAX393EPE fits precision test and measurement systems that route multiple low-frequency signals through one instrument front end. Its four SPST switches provide independent path selection, while guaranteed on-resistance matching below 2 Ω and flatness below 2 Ω reduce channel-dependent amplitude errors. A typical implementation places switched sources, reference inputs, or guard signals on the instrument PCB and drives each control line from the measurement controller. The 16-pin DIP format supports through-hole sockets and conventional laboratory-card construction. Designers should still verify input bandwidth, charge injection, leakage, and control timing for the specific signal amplitude and measurement bandwidth.
推薦
Data Acquisition Input Multiplexing
The MAX393EPE is suitable for controlled signal selection in a data-acquisition input network. Its typical on-resistance of 20 Ω can be used to connect sensor or reference channels to a shared analog front end when signal bandwidth and source impedance are compatible with that resistance. Matching below 2 Ω between channels helps limit gain imbalance, while flatness below 2 Ω reduces output variation across the signal range. The device may be placed between a terminal board and the analog measurement circuitry. High-impedance sensors can require additional buffering because switch on-resistance, capacitance, leakage, and injected charge all influence measurement accuracy.
推薦
Industrial Instrumentation
The MAX393EPE supports analog routing in industrial instrumentation that must operate from a single supply or bipolar rails. Its +3 V to +15 V single-supply range accommodates compact control systems, while ±3 V to ±8 V operation suits instrumentation handling signals around ground. Four independent switches can isolate sensors, select filters, or connect calibration references without adding continuous relay drive power. The below-1 µW power-consumption figure is useful in continuously powered equipment. Industrial designs must still account for the actual operating-temperature grade, transient protection, ground-loop behavior, and the control levels required by the surrounding controller.
推薦
Sample-and-Hold Signal Routing
The MAX393EPE can route sampling-related signals where four independently selected paths must be controlled by digital logic. Its precision SPST arrangement allows a hold capacitor, acquisition source, reference, and reset path to be connected selectively, subject to the data sheet’s switching-time and charge-injection limits. Low on-resistance variation helps maintain consistent settling behavior among channels, while the compact 16-pin DIP supports straightforward through-hole implementation. In practical sample-and-hold circuits, the control edge should occur while the acquisition path is no longer sensitive to injected charge, and the capacitor’s dielectric absorption and leakage should be evaluated separately.
推薦
Laboratory Automation
The MAX393EPE is appropriate for laboratory automation equipment that repeatedly routes analog signals between instruments, sensors, and reference sources. Four SPST switches reduce the number of discrete routing elements required for a basic analog matrix, and the 16-pin DIP package is convenient for socketed or hand-built control cards. The guaranteed matching and flatness characteristics help maintain repeatability when different channels are selected. Because each transition can create a temporary output disturbance through charge injection, acquisition systems should blank or reject samples during switching. Control traces should also be kept away from sensitive analog nodes to minimize capacitive coupling.
推薦
Bipolar Sensor Interface
The MAX393EPE can interface bipolar sensors when the system uses split supplies from ±3 V to ±8 V. Each SPST switch may connect a positive, negative, or reference-sensing path to a common conditioning channel while the common-mode voltage remains within the device operating limits. Matching below 2 Ω and on-resistance flatness below 2 Ω help preserve channel consistency across changing sensor voltages. The low-power switching characteristic is favorable for portable or continuously monitored instrumentation. Designers should verify absolute-maximum input voltage, off-state leakage, control-signal polarity, and whether the sensor source impedance makes the switch resistance significant relative to the required measurement accuracy.
推薦
推薦產品摘要
工程參考資料,適用於 MAX393EPE — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX393CPE | MAX393EUE | MAX393ESE | MAX393EAA | MAX393CUE |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-pin DIP | 16-pin DIP | 16-pin DIP | 16-pin DIP | 16-pin DIP | 16-pin DIP |
| Number of Switches | 4 | 4 | 4 | 4 | 4 | 4 |
| Switch Configuration | Quad SPST | Quad SPST | Quad SPST | Quad SPST | Quad SPST | Quad SPST |
主要差異化特點
- Guaranteed channel matching supports consistent precision measurements (對比MAX393CPE)
- Low on-resistance flatness reduces signal-dependent amplitude variation (對比MAX393EUE)
- Supports both compact single-supply and bipolar instrumentation designs (對比MAX393ESE)
- Low power consumption suits continuously powered analog routing (對比MAX393EAA)
設計說明
Treat charge injection as a sampling-timing issue rather than only a DC offset issue. When a control line changes state, the transition can produce a temporary voltage disturbance at the switched output. If the downstream amplifier samples immediately, allow the output to settle or blank the sample during the transition. Keep switching-control traces away from sensitive input and output nodes, and use a ground reference close to the device to reduce coupling into high-impedance measurement paths.
Route the analog switched paths as short and direct as practical, with a continuous ground plane and minimal stub branches. The MAX393EPE uses a through-hole DIP footprint, so component placement can reduce parasitic capacitance compared with a dense surface-mount layout. Avoid placing high-current or fast-switching traces adjacent to the switched nodes. Maintain the clearances required for the selected switching voltage and installed package.
Do not assume that all MAX393 ordering codes are automatically interchangeable. Confirm the package dimensions, lead finish, pin numbering, temperature grade, absolute-maximum ratings, and control-input thresholds for every candidate. The MAX393EPE is a 16-pin DIP part, and the MAX393 family’s suffix changes can indicate meaningful differences. A physical fit alone does not prove electrical or environmental equivalence.
Select the supply arrangement from the actual signal range: +3 V to +15 V for single-supply use or ±3 V to ±8 V for bipolar operation. Ensure that control levels remain valid in the chosen configuration and that all switched input and output voltages stay within the absolute-maximum limits. The below-1 µW power-consumption specification should not be interpreted as total system consumption because control-driver current and off-state leakage also contribute.
合規資訊
The industrial temperature designation does not by itself imply AEC-Q100 qualification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established by the cited product information.