MAX4854HETE+T - 9 Ohm Quad SPST Signal Switch | Analog Devices
MPN: MAX4854HETE+T ✓ AktifMAX4854HETE+T Ringkasan
An analog switch is an integrated circuit that connects or disconnects signal paths under digital control. The SPST designation means each internal switch provides one normally closed or selectable single-pole, single-throw path. As part of the interface IC hierarchy, the MAX4854HETE+T provides controlled routing between external circuitry and a protected signal path. Its quad-channel architecture integrates four switching circuits into one compact package.
The device offers a 9 ohm on-resistance, a 1:1 configuration, and four SPST circuits. These characteristics are useful where a design needs several selectable signal paths rather than a single high-current power switch. The manufacturer datasheet identifies the part as a high-bandwidth, signal-line protection switch. Its surface-mount TQFN package also supports compact PCB layouts where analog routing and protection must be integrated close to the controlled signal source.
The MAX4854HETE+T uses four control inputs to operate its four SPST channels. Control-signal timing, output capacitance, bandwidth, logic thresholds, and switch leakage determine how cleanly the device can pass short analog signals. Because these operating characteristics depend on the system’s signal amplitude, source impedance, load, and layout, designers should use the manufacturer datasheet limits when checking the complete signal path and logic compatibility.
Typical uses include protected analog signal routing, test and measurement interfaces, communications equipment, data-acquisition systems, and industrial control boards. The quad-channel organization is particularly useful when several external nodes must be isolated, routed, or protected through common control logic. It can reduce component count compared with four discrete single-channel switches while keeping routing in a compact package.
For reliable implementation, place the device close to the protected signal path and route high-speed or high-current connections with short traces and a continuous ground reference. Confirm logic levels and control timing before enabling the switches. Also account for off isolation, on capacitance, and leakage when the signal amplitude is small or the application requires low crosstalk.
This page combines the device’s circuit configuration, package information, sourcing fields, and engineering guidance with practical design considerations. It also identifies the limited drop-in options found for this footprint so that board designers can distinguish a confirmed replacement from merely similar switching devices.
Alternatif penggantian untuk MAX4854HETE+T — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MAX4854HETE+T (sama faktor bentuk dan footprint) — berbeda di dalam Package, Switch Type.
MAX4854HETE+
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX4854HETE+T Rating Maksimal & Karakteristik Listrik
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 |
| On-Resistance | 9 ohm |
| Switch Type | Quad SPST |
| Signal-Line Function | High-bandwidth signal-line protection switching |
| Number of Terminals | 16 terminals |
| Paket | TQFN-16 (HVQCCN), 3 x 3 mm |
| Package Shape | Square |
| Tipe Mounting | Surface mount |
| Temperature Grade | Industrial |
MAX4854HETE+T square Diamant Konfigurasi Panduan
Konfigurasi pin untuk MAX4854HETE+T (square pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk MAX4854HETE+T.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MAX4854HETE+T cocok untuk 6 aplikasis: Protected Analog Signal Routing, Test and Measurement Interfaces, Data-Acquisition Systems, Communications Equipment, Industrial Control Systems, Audio Signal Selection.
Protected Analog Signal Routing
The MAX4854HETE+T fits protected analog routing because it combines four SPST channels, a 1:1 configuration, and a 9 ohm on-resistance in one 3 x 3 mm TQFN package. Each channel can provide a controlled connection between a signal source and its destination while the other paths remain separately controlled. The integration reduces the number of discrete switch packages on a multi-node analog board. Designers should verify that 9 ohm is acceptable for the source impedance and signal amplitude, and should compare the datasheet on-capacitance and leakage values with the bandwidth budget before finalizing the layout.
Direkomendasikan
Test and Measurement Interfaces
The MAX4854HETE+T is suitable for test and measurement interfaces where several low-level analog paths must be routed under instrument control. Its four SPST channels and 9 ohm on-resistance can connect sources, attenuators, filters, or external test points while keeping the routing network compact. The manufacturer describes the part as a high-bandwidth signal-line protection switch, supporting its use in protected measurement paths. Before selecting it for precision instrumentation, compare input capacitance, leakage, off isolation, and logic thresholds with the instrument’s source impedance and required measurement bandwidth.
Direkomendasikan
Data-Acquisition Systems
The MAX4854HETE+T can route four channels in a compact data-acquisition front end where sensor or source selection must be under software or hardware control. Its 1:1 SPST organization avoids an alternate signal path, while the 9 ohm on-resistance establishes the insertion impedance that the source and acquisition circuitry must tolerate. The 16-terminal TQFN package helps keep routing close to sensitive analog nodes and away from long unprotected traces. Use the manufacturer’s control timing, capacitance, leakage, and operating-voltage limits to confirm compatibility with the ADC driver and acquisition sequencer.
Direkomendasikan
Communications Equipment
The MAX4854HETE+T fits communications equipment requiring compact, controlled routing of multiple protected lines. Its four SPST channels can manage auxiliary or lower-bandwidth signal paths where the source impedance permits a 9 ohm switch resistance and the required bandwidth remains inside the manufacturer’s operating limits. Keeping the device near the connector or protected line can reduce exposure of sensitive nodes and shorten PCB routing. Logic thresholds, supply requirements, switch capacitance, and off-isolation characteristics should be checked against the communications controller and connector environment before release to production.
Direkomendasikan
Industrial Control Systems
The MAX4854HETE+T can support signal routing in industrial control systems where multiple external lines require controlled isolation from an analog or controller section. The quad SPST architecture consolidates four switching paths in a compact 3 x 3 mm surface-mount footprint, while the signal-line protection function helps place switching close to exposed circuitry. Engineers should account for the industrial temperature grade, logic thresholds, leakage, and off isolation when defining system behavior. PCB layout should keep the control traces away from sensitive analog paths and provide a low-impedance ground connection to the exposed pad.
Direkomendasikan
Audio Signal Selection
The MAX4854HETE+T is appropriate for audio signal selection when four SPST paths must be routed with a compact, high-bandwidth-oriented switch. The 9 ohm on-resistance may be acceptable for many line-level paths, but it can create a divider with the source impedance and load, affecting level and damping. Because the manufacturer positions the device as a high-bandwidth signal-line protection switch, it can sit near a protected input and shorten sensitive traces. Verify the actual bandwidth, off isolation, capacitance, and logic levels against the audio source, amplifier input, and system grounding arrangement.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MAX4854HETE+T — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MAX4854HETE+ |
|---|---|---|
| Package | TQFN-16 (HVQCCN) 3x3 mm | TQFN-16 (HVQCCN) 3x3 mm |
| Brand | Analog Devices | Analog Devices |
| Number of Circuits | 4 circuits | 4 circuits |
| Switch Configuration | 1:1 | 1:1 |
| On-Resistance | 9 ohm | 9 ohm |
| Switch Type | Quad SPST | Quad SPST |
| Number of Terminals | 16 terminals | 16 terminals |
| Signal-Line Function | High-bandwidth signal-line protection switching | High-bandwidth signal-line protection switching |
Diferensiator Kunci
- Four SPST channels integrated into one compact package (vsMAX4854HETE+)
- Direct 1:1 signal configuration (vsMAX4854HETE+)
- Matching 9 ohm on-resistance (vsMAX4854HETE+)
Catatan Desain
Follow the manufacturer's TQFN land pattern exactly, including the exposed-pad dimensions and solder-mask guidance. Place the device close to the protected signal node so that switching occurs before the trace reaches sensitive circuitry. Keep the exposed pad connected to the board ground plane with a short thermal path and avoid placing a keepout that isolates the pad from ground copper.
Evaluate the complete source impedance, 9 ohm on-resistance, switch capacitance, and destination input impedance as one divider. For low-amplitude or high-impedance nodes, even a modest resistance can reduce signal level, while capacitance can increase rise and fall times. Use short traces, a continuous reference plane, and ground returns adjacent to each protected line.
Do not treat a switch with the same TQFN outline as a drop-in replacement without comparing its terminal assignment and electrical limits. Likewise, do not substitute MAX4899AEETE+T solely because it is a related Maxim interface device; its pin functions and electrical characteristics must be verified independently. Validate logic thresholds, control polarity, supply range, and switch state before production release.
Route the four control inputs away from the analog switch nodes and provide a low-impedance ground reference near the package. If control signals originate on a different board region, use a ground-referenced buffer or properly terminated driver rather than allowing long floating traces. This reduces switching transients coupled into the protected signal paths.
Informasi Konformitas
The device is an industrial-temperature interface IC; automotive qualification is not indicated. Compliance status is not stated in the listed product records.