onsemi

MC14052BF - Dual 4:1 CMOS Multiplexer | onsemi

MPN: MC14052BF ✓ Aktif
280 ohm Rds(on) 16-pin SO EIAJ surface-mount package Package
MOQ: 1 |

MC14052BF Ringkasan

The onsemi MC14052BF is a dual 4:1 differential CMOS analog multiplexer with an on-resistance of 280 ohm, packaged in a 16-pin SO EIAJ surface-mount package. It combines two independently controlled 4:1 selectors in one IC, allowing eight analog inputs to be routed to two outputs while conserving board space. The device is suitable for instrumentation, signal routing, data acquisition, and test systems that require bipolar-compatible analog switching.

An analog multiplexer is an interface IC that connects one of several input channels to a shared output path using digital address and control signals. The MC14052BF belongs to the broader multiplexer and analog-switch hierarchy, where its 4:1 configuration provides more input selection than a single-pole switch. Because one package contains two circuits, it can perform complementary selection, differential measurement, or redundant routing without requiring two separate switch ICs.

The MC14052BF provides two switch circuits, eight analog input terminals, two analog outputs, four address inputs, and inhibit and enable controls in a 16-pin package. Its 280-ohm on-resistance makes it suitable for circuits in which moderate insertion resistance is acceptable. The manufacturer also identifies the MC14052BF as a pin-for-pin replacement for CD4051, CD4052, and CD4053 families, although their internal channel counts and pin functions must be checked before using that statement as a design rule.

The architecture is based on complementary CMOS transmission gates, allowing analog signals to be connected or isolated under digital control. Address inputs select the active input path, while the inhibit and enable inputs provide gating for system-level control. The manufacturer datasheet also identifies low-noise operation of 12 nV per square-root hertz at frequencies of 1.0 kHz and above, making the device relevant to low-level analog measurement paths.

Typical uses include multimeter and oscilloscope input switching, automated test equipment, sensor signal selection, communication-channel routing, and data-acquisition systems. Two internal selectors are especially useful when a system must compare two instruments, route complementary signals, or maintain control paths around a measurement chain. These applications benefit from centralized channel selection while requiring careful attention to address timing, enable logic, and off-channel behavior.

Design with the MC14052BF by treating its control inputs as digital signals referenced to the same supply used by the analog path. Keep sensitive analog routing away from high-current switching nodes and provide a stable ground reference. Check signal amplitudes against the switch's operating limits, observe the required logic states for address, inhibit, and enable pins, and verify the package dimensions before footprint assembly.

This product page consolidates the device's multiplexer configuration, package information, sourcing information, drop-in candidates, and practical engineering guidance. It also distinguishes documented pin-for-pin relationships from design decisions that still require verification of voltage ratings, logic levels, channel assignments, and application-specific performance.

Alternatif penggantian untuk MC14052BF — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian MC14052BF (sama faktor bentuk dan footprint) — berbeda di dalam Multiplexer Configuration, Noise Density, Package.

onsemi
Multiplexer Configuration: Dual 2:4 analog multiplexer/demultiplexer
Noise Density: 12 nV/sqrt(Hz) at f greater than or equal to 1.0 kHz
Package: 16-pin SOIC
Bandingkan dengan MC14052BF →

MC14052BD

✅ Drop-In
onsemi
📦 16-SOIC
Dual 2:4 analog multiplexer/demultiplexer · 2 circuits · 280 ohm · 3 V to 18 V · 16-pin SOIC · 16 pins · Surface mount · 12 nV/sqrt(Hz) at f greater than or equal to 1.0 kHz

Kontak untuk harga

Lihat Datasheet →

MC14052BDG

✅ Drop-In
📦 16-SOIC
Identical 280-ohm-class performance and 16-pin terminal arrangement; the ordering-suffix qualification or marking differs from MC14052BF.

📋 Alternatif referensi (tidak dalam katalog)

MC14052BF Spesifikasi

Product Type Dual 4:1 differential analog multiplexer, 2 circuits
Number of Circuits 2 circuits
Multiplexer Configuration Dual 4:1 configuration
On-Resistance 280 ohm
Tetesan Bising 12 nV/sqrt(Hz) at 1.0 kHz and above
Jumlah Pin 16 pins
Paket 16-pin SO EIAJ surface-mount package
Tipe Mounting Surface mount
Temperature Grade Military grade
Device Classification Analog switch, multiplexer, and demultiplexer IC
Signal Type Differential analog signal
Pin-for-Pin Reference CD4051, CD4052, and CD4053 families, subject to application verification
Lower On-Resistance Reference HC4051, HC4052, and HC4053 high-speed CMOS devices
Related 4PDT Device MC14551B
Lead-Free Package Availability Available

MC14052BF available Diamant Konfigurasi Panduan

Konfigurasi pin untuk MC14052BF (available pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai available untuk MC14052BF

Tidak ada data diatribut pin yang tersedia untuk MC14052BF.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

MC14052BF cocok untuk 6 aplikasis: Digital Multimeter Input Switching, Oscilloscope and Instrumentation Signal Routing, Sensor Signal Multiplexing, Automated Test Equipment Channel Selection, Communications Channel Routing, Precision Analog Signal Selection.

🔧

Digital Multimeter Input Switching

The MC14052BF is useful in a digital multimeter that must route several measurement inputs to a common analog front end. Its two 4:1 selectors can handle complementary or grouped measurement paths while the 280-ohm on-resistance remains suitable for many source impedances. The documented noise density of 12 nV/sqrt(Hz) at 1.0 kHz and above is valuable when low-level measurements are part of the design. Address and enable signals should be driven from the meter controller, while the analog source impedance and acquisition time must be checked against the complete electrical characteristics.

📺

Oscilloscope and Instrumentation Signal Routing

The MC14052BF can route multiple instrument or probe nodes to a shared measurement amplifier in automated test and oscilloscope systems. Two independent 4:1 sections allow paired signals to be selected together, reducing the number of separate switch packages required on the board. Its 280-ohm on-resistance must be included in the source and amplifier impedance budget, while the 12 nV/sqrt(Hz) noise specification helps preserve low-level measurement quality. Place the multiplexer close to the sensitive amplifier and keep digital address traces away from analog inputs.

🏭

Sensor Signal Multiplexing

The MC14052BF can consolidate several sensor outputs into a shared amplifier or data-conversion input in industrial monitoring equipment. Its dual 4:1 organization supports two sensor groups, complementary measurements, or redundant channels without requiring two multiplexer packages. The 280-ohm on-resistance is important for high-impedance sensors because it interacts directly with sensor impedance, leakage, and settling time. Confirm the complete switch characteristics, input bias requirements, and supply range, then place the device near the sensor interface to minimize sensitive-node leakage and interference.

⚡

Automated Test Equipment Channel Selection

In automated test equipment, the MC14052BF provides two 4:1 selectors for directing test channels toward a common measurement or comparison path. This arrangement can reduce component count when both positive and negative, or complementary, nodes must be controlled. The on-resistance of 280 ohm makes source loading an important design consideration for high-impedance DUTs, and the manufacturer noise figure of 12 nV/sqrt(Hz) at 1.0 kHz and above supports precision measurements. Validate settling behavior for the fastest test rates and keep switching transients away from sensitive fixtures.

🌐

Communications Channel Routing

The MC14052BF can select among several low-frequency or baseband paths in communication equipment where two analog routes must share downstream converters or amplifiers. The two internal 4:1 selectors support symmetric or complementary routing, while the 280-ohm on-resistance contributes to channel insertion loss and must be balanced against downstream impedance. Its low documented noise density makes it more attractive for low-level paths than a purely mechanical routing solution. The designer should verify signal swing, bandwidth, supply level, and isolation against the complete ON Semiconductor electrical characteristics.

📡

Precision Analog Signal Selection

The MC14052BF fits precision analog signal-selection blocks in laboratory equipment, process controls, and low-level measurement systems. A documented noise density of 12 nV/sqrt(Hz) at 1.0 kHz and above, combined with two independently addressed 4:1 sections, enables several sensitive inputs to reach a common conditioning amplifier. The 280-ohm on-resistance still forms part of the complete noise-gain and loading calculation, so source impedance, amplifier bias current, and settling time require evaluation. Use a quiet ground plane, short analog traces, and stable decoupling near the device.

Ringkasan Produk Direkomendasikan

CD4051B Texas Instruments Digunakan di dalam: Digital Multimeter Input Switching, Sensor Signal Multiplexing, Communications Channel Routing CD4052B Texas Instruments Digunakan di dalam: Digital Multimeter Input Switching, Oscilloscope and Instrumentation Signal Routing, Sensor Signal Multiplexing, Automated Test Equipment Channel Selection, Communications Channel Routing, Precision Analog Signal Selection CD4053B Pin-for-pin replacement family identified by the manufacturer datasheet Digunakan di dalam: Digital Multimeter Input Switching, Sensor Signal Multiplexing, Communications Channel Routing HC4052B Lower on-resistance high-speed CMOS alternative family Digunakan di dalam: Oscilloscope and Instrumentation Signal Routing, Automated Test Equipment Channel Selection, Precision Analog Signal Selection MC14551B Related onsemi 4PDT switch Digunakan di dalam: Oscilloscope and Instrumentation Signal Routing, Automated Test Equipment Channel Selection, Precision Analog Signal Selection
What is the MC14052BF?
The MC14052BF is an onsemi dual 4:1 differential analog multiplexer with a documented on-resistance of 280 ohm and a low-noise figure of 12 nV/sqrt(Hz) at 1.0 kHz and above. According to the ON Semiconductor datasheet, the IC contains two switching circuits in a 16-pin SO EIAJ package. It is intended for routing analog signals under digital address and enable control.
What is the operating voltage of MC14052BF?
The MC14052BF operating voltage is not stated in the cited manufacturer excerpt, so the supply limits must be confirmed in the complete ON Semiconductor datasheet before design use. The device is a CMOS analog multiplexer, but its valid input, output, and supply ranges cannot be inferred from its 280-ohm on-resistance. Apply the limits listed in the datasheet electrical-characteristics table.
What is the pinout of MC14052BF?
The MC14052BF uses a 16-pin SO EIAJ package, but a pin-by-pin public pinout is not included in the cited material. Use the manufacturer datasheet pin-description table when assigning addresses, inhibit, enable, analog inputs, outputs, and supply connections. The package drawing also identifies the EIAJ outline, so do not assume that a generic SOIC-16 footprint is mechanically identical.
Where can I download the MC14052BF datasheet PDF?
The MC14052BF datasheet PDF can be accessed through the cited ON Semiconductor datasheet page at alldatasheet.com. According to that document listing, the manufacturer datasheet includes linearized transfer characteristics, noise information, a 280-ohm switching characteristic, and pin-for-pin replacement guidance for CD4051, CD4052, and CD4053 devices. Review the complete PDF for electrical limits and package dimensions.
Can MC14052BF replace a CD4052?
The ON Semiconductor datasheet identifies MC14052BF as pin-for-pin compatible with the CD4051, CD4052, and CD4053 families. A CD4052 is the closest functional comparison because both devices provide dual 4:1 multiplexing. The manufacturer statement is a strong replacement indication, but production designs should still verify supply voltage, logic levels, control polarity, and analog signal limits against the specific CD4052 variant.
MC14052BF vs MC14052BD - which is the better replacement?
The MC14052BF and MC14052BD are both identified by cross-reference information as completely replaceable 16-pin devices with consistent main performance parameters and terminal assignments. The MC14052BF is identified as the military-temperature-grade ordering option in a distributor listing, while the exact grade of MC14052BD should be checked in its own datasheet. Choose according to the required temperature grade and production qualification.
When should I choose MC14052BF over another CMOS multiplexer?
Choose the MC14052BF when a design needs two 4:1 analog selectors, a 280-ohm on-resistance, and low-noise multiplexing in one 16-pin package. It is particularly useful when a system must compare two channels, route complementary signals, or reduce the number of separate switch ICs. Select another device when lower on-resistance, higher bandwidth, a different supply range, or a different package is required.
Is MC14052BF suitable for low-level analog measurements?
The MC14052BF is suitable for many low-level analog-routing tasks because the manufacturer reports a noise density of 12 nV/sqrt(Hz) at 1.0 kHz and above and documents a 280-ohm on-resistance. Suitability also depends on source impedance, bandwidth, leakage, offset behavior, and the selected power supply. Use low-noise op-amp layouts and avoid routing the sensitive node through unnecessary switch stages.
What is the best drop-in replacement for MC14052BF?
The best directly documented replacement candidates are the MC14052BD and MC14052BDG, both described by cross-reference information as having consistent terminals, packages, and main performance parameters. Cross-reference sources specifically report complete replacement without PCB modification for the MC14052BDG comparison. Verify the exact suffix, temperature grade, supply range, and lifecycle requirements before approving either part.
Can MC14052BDG replace MC14052BF?
Yes, MC14052BDG is identified as a complete replacement for MC14052BF because the comparison reports consistent terminals, package, and principal performance characteristics. The MC14052BF and MC14052BDG are both represented as 16-pin SOIC devices in that cross-reference comparison. Final qualification should still check the operating-temperature grade and electrical limits required by the production design.
Where can I buy MC14052BF online?
The MC14052BF is listed through multiple authorized distribution channels, while XAIPART provides a Request a Quote form on this page for current commercial terms, stock status, and lead time. Use that form to request the exact MC14052BF ordering information and quantity required for your build. Pricing and availability can change, so the form is the appropriate source for a current quotation.
What is the price of MC14052BF?
The current MC14052BF price should be requested through the Request a Quote form on this page because commercial terms can vary with quantity, package quantity, and market conditions. No static price figure should be used for budgeting without a current quotation. The form also lets you request stock confirmation, expected lead time, and traceability requirements for production purchasing.
What is the lead time for MC14052BF?
A current MC14052BF lead time is not stated in the cited manufacturer or distributor excerpts. Use the Request a Quote form on this page to ask for the latest lead time, minimum order quantity, and available package quantity. For production planning, include your required delivery date and annual usage so the quotation can reflect realistic supply commitments.
Is MC14052BF in stock?
Stock status for MC14052BF should be confirmed through the Request a Quote form on this page rather than inferred from a search-result snippet. The part is actively listed by multiple distribution channels, which indicates current market availability, but does not guarantee a quantity at the time of your order. State the required quantity, date code preference, and shipping destination when requesting a quotation.
What are the key specifications of MC14052BF that engineers should know?
The key MC14052BF specifications are its dual 4:1 analog-multiplexer configuration, two internal circuits, 280-ohm on-resistance, 12 nV/sqrt(Hz) noise density at 1.0 kHz and above, and 16-pin SO EIAJ package. According to the ON Semiconductor datasheet, it also offers pin-for-pin replacement relationships with CD4051, CD4052, and CD4053 devices and includes a 12 nV/sqrt(Hz) low-noise figure.
Is MC14052BF the same as CD4052?
The MC14052BF is a pin-for-pin replacement for the CD4052 according to the ON Semiconductor datasheet, and both are dual 4:1 multiplexer functions. They should therefore be closely related in board-level use. Do not treat the wording as a blanket guarantee across every CD4052 variant: confirm supply voltage, control logic, signal limits, acquisition time, and environmental qualification for the specific production part.
What is the best onsemi equivalent for MC14052BF?
The MC14052BD and MC14052BDG are the strongest documented onsemi equivalents because cross-reference information describes consistent terminal assignments, packages, and main performance characteristics. The BF suffix is associated with a military-grade listing, while the exact environmental grade of each alternative depends on its ordering code. Select the suffix that meets the temperature and reliability requirements of the equipment.

Data referensi engineering untuk MC14052BF — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose MC14052BF for new military-temperature-grade designs that require a dual 4:1 analog multiplexer with 280-ohm on-resistance and documented low noise. MC14052BD is a direct onsemi alternative when its specific ordering code meets the required environmental and qualification criteria; cross-reference information indicates consistent terminals, package, and principal performance. MC14052BDG provides another documented 16-pin replacement route for inventory or lifecycle continuity. Do not select these merely by suffix when the original design depends on military-grade screening or exact date-code controls. For designs requiring lower on-resistance or higher switching speed, examine the HC4051, HC4052, or HC4053 families instead, because the MC14052BF trades conduction resistance for lower-noise CMOS multiplexing. Always confirm supply voltage, logic thresholds, signal limits, timing, and package dimensions against the complete datasheet before production release.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini MC14052BD MC14052BDG
Brand onsemi onsemi onsemi
Package 16-SOIC 16-SOIC - same 16-SOIC - same
Multiplexer Configuration Dual 4:1 Dual 4:1 Dual 4:1
Number of Circuits 2 circuits 2 circuits 2 circuits
On-Resistance 280 ohm 280 ohm 280 ohm
Noise Density 12 nV/sqrt(Hz) at 1.0 kHz and above 12 nV/sqrt(Hz) at 1.0 kHz and above 12 nV/sqrt(Hz) at 1.0 kHz and above
Pin Count 16 pins 16 pins 16 pins
Pin Compatibility 16-pin dual 4:1 multiplexer Complete replacement without package modification Complete replacement without package modification

Diferensiator Kunci

  • Two 4:1 selectors integrated into one package (vsMC14052BD)
  • Documented low-noise analog switching (vsMC14052BDG)
  • Manufacturer-documented pin-for-pin family support (vsMC14052BD)

Catatan Desain

Do not treat the datasheet statement that MC14052BF is pin-for-pin compatible with CD4051, CD4052, and CD4053 as permission to substitute one package for another without checking the complete pin descriptions. Those devices have different multiplexing configurations, while CD4052 is the closest functional match. Verify the EIAJ land pattern, supply limits, control logic, signal swing, and acquisition behavior before approving a cross-family replacement.

Include the 280-ohm on-resistance in the source-loading and amplifier-gain calculation. The resistance creates a divider with the source and amplifier impedances, while switch capacitance and leakage can influence settling time and common-mode behavior. For low-level signals, keep the source impedance high enough for useful performance but low enough to control the divider error, and verify settling against the fastest required address transition.

Place the MC14052BF close to the analog source or destination and route the sensitive analog paths as short, guarded traces. Keep address, inhibit, enable, and supply-return traces away from high-impedance input nodes to reduce capacitive feedthrough. Provide local supply bypassing at the device and use a continuous ground reference; the exact capacitor value and stability network must be selected from the manufacturer guidance and the completed schematic.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The manufacturer datasheet states that lead-free packages are available, but no explicit RoHS, REACH, halogen-free, or conflict-minerals conclusion appears in the cited material. The component is a military-temperature-grade interface IC, so AEC-Q100 is not the applicable automotive qualification.

Data disahkan pada: 2026-11-11 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

MC14052BF datasheet MC14052BF datasheet pdf MC14052BF pinout MC14052BF equivalent MC14052BF replacement MC14052BF cross reference MC14052BF vs MC14052BD onsemi MC14052BF MC14052BF price MC14052BF stock MC14052BF footprint MC14052BF application circuit

Komponen dan Istilah Terkait

onsemi MC14052BF MC14052BD MC14052BDG CD4051B CD4052B CD4053B HC4051B HC4052B HC4053B MC14551B analog multiplexer analog switch demultiplexer dual 4:1 multiplexer CMOS transmission gate interface IC signal routing on-resistance 280 ohm 12 nV/sqrt(Hz) 16-pin SO EIAJ surface-mount package digital multimeter automated test equipment
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ