MC14052BF - Dual 4:1 CMOS Multiplexer | onsemi
MPN: MC14052BF ✓ NakahandaMC14052BF Ulas
An analog multiplexer is an interface IC that connects one of several input channels to a shared output path using digital address and control signals. The MC14052BF belongs to the broader multiplexer and analog-switch hierarchy, where its 4:1 configuration provides more input selection than a single-pole switch. Because one package contains two circuits, it can perform complementary selection, differential measurement, or redundant routing without requiring two separate switch ICs.
The MC14052BF provides two switch circuits, eight analog input terminals, two analog outputs, four address inputs, and inhibit and enable controls in a 16-pin package. Its 280-ohm on-resistance makes it suitable for circuits in which moderate insertion resistance is acceptable. The manufacturer also identifies the MC14052BF as a pin-for-pin replacement for CD4051, CD4052, and CD4053 families, although their internal channel counts and pin functions must be checked before using that statement as a design rule.
The architecture is based on complementary CMOS transmission gates, allowing analog signals to be connected or isolated under digital control. Address inputs select the active input path, while the inhibit and enable inputs provide gating for system-level control. The manufacturer datasheet also identifies low-noise operation of 12 nV per square-root hertz at frequencies of 1.0 kHz and above, making the device relevant to low-level analog measurement paths.
Typical uses include multimeter and oscilloscope input switching, automated test equipment, sensor signal selection, communication-channel routing, and data-acquisition systems. Two internal selectors are especially useful when a system must compare two instruments, route complementary signals, or maintain control paths around a measurement chain. These applications benefit from centralized channel selection while requiring careful attention to address timing, enable logic, and off-channel behavior.
Design with the MC14052BF by treating its control inputs as digital signals referenced to the same supply used by the analog path. Keep sensitive analog routing away from high-current switching nodes and provide a stable ground reference. Check signal amplitudes against the switch's operating limits, observe the required logic states for address, inhibit, and enable pins, and verify the package dimensions before footprint assembly.
This product page consolidates the device's multiplexer configuration, package information, sourcing information, drop-in candidates, and practical engineering guidance. It also distinguishes documented pin-for-pin relationships from design decisions that still require verification of voltage ratings, logic levels, channel assignments, and application-specific performance.
Mga alternatibo na pwedeng ilagay na MC14052BF — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok MC14052BF (parehas na form factor at footprint) — pagkakaiba sa Multiplexer Configuration, Noise Density, Package.
MC14052BD
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →MC14052BDG
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
MC14052BF Mga Spesipikasyon
| Product Type | Dual 4:1 differential analog multiplexer, 2 circuits |
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | Dual 4:1 configuration |
| On-Resistance | 280 ohm |
| Density ng Noise | 12 nV/sqrt(Hz) at 1.0 kHz and above |
| Bilang ng Pins | 16 pins |
| Packhaging | 16-pin SO EIAJ surface-mount package |
| Uri ng Pagpapasok | Surface mount |
| Temperature Grade | Military grade |
| Device Classification | Analog switch, multiplexer, and demultiplexer IC |
| Signal Type | Differential analog signal |
| Pin-for-Pin Reference | CD4051, CD4052, and CD4053 families, subject to application verification |
| Lower On-Resistance Reference | HC4051, HC4052, and HC4053 high-speed CMOS devices |
| Related 4PDT Device | MC14551B |
| Lead-Free Package Availability | Available |
Gabay sa Pin Configuration ng MC14052BF available
Pin configuration para sa MC14052BF (available package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa MC14052BF.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
MC14052BF ay nararapat para sa 6 aplikasyons: Digital Multimeter Input Switching, Oscilloscope and Instrumentation Signal Routing, Sensor Signal Multiplexing, Automated Test Equipment Channel Selection, Communications Channel Routing, Precision Analog Signal Selection.
Digital Multimeter Input Switching
The MC14052BF is useful in a digital multimeter that must route several measurement inputs to a common analog front end. Its two 4:1 selectors can handle complementary or grouped measurement paths while the 280-ohm on-resistance remains suitable for many source impedances. The documented noise density of 12 nV/sqrt(Hz) at 1.0 kHz and above is valuable when low-level measurements are part of the design. Address and enable signals should be driven from the meter controller, while the analog source impedance and acquisition time must be checked against the complete electrical characteristics.
Inirekomenda
Oscilloscope and Instrumentation Signal Routing
The MC14052BF can route multiple instrument or probe nodes to a shared measurement amplifier in automated test and oscilloscope systems. Two independent 4:1 sections allow paired signals to be selected together, reducing the number of separate switch packages required on the board. Its 280-ohm on-resistance must be included in the source and amplifier impedance budget, while the 12 nV/sqrt(Hz) noise specification helps preserve low-level measurement quality. Place the multiplexer close to the sensitive amplifier and keep digital address traces away from analog inputs.
Inirekomenda
Sensor Signal Multiplexing
The MC14052BF can consolidate several sensor outputs into a shared amplifier or data-conversion input in industrial monitoring equipment. Its dual 4:1 organization supports two sensor groups, complementary measurements, or redundant channels without requiring two multiplexer packages. The 280-ohm on-resistance is important for high-impedance sensors because it interacts directly with sensor impedance, leakage, and settling time. Confirm the complete switch characteristics, input bias requirements, and supply range, then place the device near the sensor interface to minimize sensitive-node leakage and interference.
Inirekomenda
Automated Test Equipment Channel Selection
In automated test equipment, the MC14052BF provides two 4:1 selectors for directing test channels toward a common measurement or comparison path. This arrangement can reduce component count when both positive and negative, or complementary, nodes must be controlled. The on-resistance of 280 ohm makes source loading an important design consideration for high-impedance DUTs, and the manufacturer noise figure of 12 nV/sqrt(Hz) at 1.0 kHz and above supports precision measurements. Validate settling behavior for the fastest test rates and keep switching transients away from sensitive fixtures.
Inirekomenda
Communications Channel Routing
The MC14052BF can select among several low-frequency or baseband paths in communication equipment where two analog routes must share downstream converters or amplifiers. The two internal 4:1 selectors support symmetric or complementary routing, while the 280-ohm on-resistance contributes to channel insertion loss and must be balanced against downstream impedance. Its low documented noise density makes it more attractive for low-level paths than a purely mechanical routing solution. The designer should verify signal swing, bandwidth, supply level, and isolation against the complete ON Semiconductor electrical characteristics.
Inirekomenda
Precision Analog Signal Selection
The MC14052BF fits precision analog signal-selection blocks in laboratory equipment, process controls, and low-level measurement systems. A documented noise density of 12 nV/sqrt(Hz) at 1.0 kHz and above, combined with two independently addressed 4:1 sections, enables several sensitive inputs to reach a common conditioning amplifier. The 280-ohm on-resistance still forms part of the complete noise-gain and loading calculation, so source impedance, amplifier bias current, and settling time require evaluation. Use a quiet ground plane, short analog traces, and stable decoupling near the device.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MC14052BF — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | MC14052BD | MC14052BDG |
|---|---|---|---|
| Brand | onsemi | onsemi | onsemi |
| Package | 16-SOIC | 16-SOIC - same | 16-SOIC - same |
| Multiplexer Configuration | Dual 4:1 | Dual 4:1 | Dual 4:1 |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
| On-Resistance | 280 ohm | 280 ohm | 280 ohm |
| Noise Density | 12 nV/sqrt(Hz) at 1.0 kHz and above | 12 nV/sqrt(Hz) at 1.0 kHz and above | 12 nV/sqrt(Hz) at 1.0 kHz and above |
| Pin Count | 16 pins | 16 pins | 16 pins |
| Pin Compatibility | 16-pin dual 4:1 multiplexer | Complete replacement without package modification | Complete replacement without package modification |
Pangunahing mga Pagkakaiba
- Two 4:1 selectors integrated into one package (kumpara saMC14052BD)
- Documented low-noise analog switching (kumpara saMC14052BDG)
- Manufacturer-documented pin-for-pin family support (kumpara saMC14052BD)
Talaan ng Disenyo
Do not treat the datasheet statement that MC14052BF is pin-for-pin compatible with CD4051, CD4052, and CD4053 as permission to substitute one package for another without checking the complete pin descriptions. Those devices have different multiplexing configurations, while CD4052 is the closest functional match. Verify the EIAJ land pattern, supply limits, control logic, signal swing, and acquisition behavior before approving a cross-family replacement.
Include the 280-ohm on-resistance in the source-loading and amplifier-gain calculation. The resistance creates a divider with the source and amplifier impedances, while switch capacitance and leakage can influence settling time and common-mode behavior. For low-level signals, keep the source impedance high enough for useful performance but low enough to control the divider error, and verify settling against the fastest required address transition.
Place the MC14052BF close to the analog source or destination and route the sensitive analog paths as short, guarded traces. Keep address, inhibit, enable, and supply-return traces away from high-impedance input nodes to reduce capacitive feedthrough. Provide local supply bypassing at the device and use a continuous ground reference; the exact capacitor value and stability network must be selected from the manufacturer guidance and the completed schematic.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer datasheet states that lead-free packages are available, but no explicit RoHS, REACH, halogen-free, or conflict-minerals conclusion appears in the cited material. The component is a military-temperature-grade interface IC, so AEC-Q100 is not the applicable automotive qualification.