MC9S12C128MPBE - 16-Bit 25MHz HCS12 MCU, 128KB Flash | NXP
MPN: MC9S12C128MPBE ✓ AktifMC9S12C128MPBE Ringkasan
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and a set of peripherals such as timers, ADCs, communication controllers, and GPIO. MCUs occupy the middle layer of the embedded system hierarchy: transistor -> logic gate -> processor core -> MCU -> embedded system -> end product. The HCS12 (CPU12) family is NXP's 16-bit successor to the HC11 and is widely used where 8-bit MCUs run out of performance but full 32-bit ARM Cortex-M parts are over-specified.
Key features include 128KB Flash, 4KB RAM, 25MHz bus speed, an enhanced capture timer, an 8-channel 10-bit ADC, multiple serial interfaces (SCI, SPI, I2C), and a controller area network (CAN) module. The 52-LQFP package exposes 40+ GPIO and supports automotive temperature grade operation. The integrated background debug mode (BDM) and on-chip voltage regulator simplify in-circuit programming and single-supply operation from 5V.
Architecturally, the S12C combines a 16-bit register-rich CPU12 core with a unified Flash controller, a multi-master bus, and a peripheral bridge. The device targets body electronics, instrument clusters, HVAC controllers, and CAN-node end points. Its instruction set is upward-compatible with the HC11, easing firmware migration from legacy 8-bit designs.
Typical applications include automotive body controllers (door modules, seat controllers, mirror adjusters), industrial CAN nodes, HVAC control boards, simple instrument clusters, and 16-bit replacement for legacy HC11 designs. The wide operating temperature range and on-chip CAN make it well suited to in-vehicle networks.
When designing with the MC9S12C128MPBE, ensure the 5V supply is decoupled close to the VDD pins, the BDM header is brought out for in-circuit debug, and the oscillator load capacitors match the crystal datasheet. Plan Flash endurance (typically 10k cycles) for any EEPROM emulation scheme.
This page synthesizes distributor pricing, drop-in S12C-family alternatives, and practical design notes not consolidated on the manufacturer datasheet.
Alternatif penggantian untuk MC9S12C128MPBE — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MC9S12C128MPBE (sama faktor bentuk dan footprint) — berbeda di dalam Program Memory Size, RAM Size, Connectivity, Core Processor, Packaging.
MC9S12C128CPBE
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MC9S12GC128MPBE
✅ Drop-InKontak untuk harga
Lihat Datasheet →MC9S12C128VPBE
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MC9S12C96VPBE
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MC9S12C64MPB
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MC9S12C128MPBE Rating Maksimal & Karakteristik Listrik
| Core | HCS12 (CPU12) |
| Lebar Bus Data | 16-bit |
| Frekuensi Bawah Maximum | 25 MHz |
| Program Memory Size | 128 KB (128K x 8) Flash |
| RAM Size | 4 KB |
| Paket | 52-LQFP (10x10 mm) |
| Tipe Mounting | Surface Mount |
| Tegangan Pemuat | 5 V (single-supply with on-chip regulator) |
| Suhu Kerja | -40C to +125C (automotive) |
| ADC | 10-bit, multi-channel |
| Communication Interfaces | SCI (UART), SPI, I2C, CAN |
| CAN Module | Yes (msCAN) |
| Timers | Enhanced Capture Timer (ECT) |
| Debug Interface | Background Debug Mode (BDM) |
| Temperature Grade | Automotive |
| Status RoHS | Compliant |
Konfigurasi Pin MC9S12C128MPBE
| Pin produk 1 | BKGD/MODC — Background Debug Mode / Mode select |
| Pin produk 2 | VDDR — Voltage regulator supply |
| Pin produk 3 | VSS — Ground |
| Pin produk 4 | VDDX — External I/O supply |
| Pin produk 5 | VSSX — External I/O ground |
| Pin produk 6 | RESET — External reset input (active low) |
| Pin produk 7 | TEST — Test mode (tie to VSS) |
| Pin produk 8 | XCLKS — Clock mode select |
| Pin produk 9 | EXTAL — External oscillator input |
| Pin produk 10 | XTAL — External oscillator output |
| Pin produk 11 | PAD0/AN0 — GPIO / ADC channel 0 |
| Pin produk 12 | PAD1/AN1 — GPIO / ADC channel 1 |
| Pin produk 13 | PAD2/AN2 — GPIO / ADC channel 2 |
| Pin produk 14 | PAD3/AN3 — GPIO / ADC channel 3 |
| Pin produk 15 | PAD4/AN4 — GPIO / ADC channel 4 |
| Pin produk 16 | PAD5/AN5 — GPIO / ADC channel 5 |
| Pin produk 17 | PAD6/AN6 — GPIO / ADC channel 6 |
| Pin produk 18 | PAD7/AN7 — GPIO / ADC channel 7 |
| Pin produk 19 | PA0 — GPIO port A bit 0 |
| Pin produk 20 | PA1 — GPIO port A bit 1 |
| Pin produk 21 | PA2 — GPIO port A bit 2 |
| Pin produk 22 | PA3 — GPIO port A bit 3 |
| Pin produk 23 | PA4 — GPIO port A bit 4 |
| Pin produk 24 | PA5 — GPIO port A bit 5 |
| Pin produk 25 | PA6 — GPIO port A bit 6 |
| Pin produk 26 | PA7 — GPIO port A bit 7 |
| Pin produk 27 | PB0 — GPIO port B bit 0 |
| Pin produk 28 | PB1 — GPIO port B bit 1 |
| Pin produk 29 | PB2 — GPIO port B bit 2 |
| Pin produk 30 | PB3 — GPIO port B bit 3 |
| Pin produk 31 | PB4 — GPIO port B bit 4 |
| Pin produk 32 | PB5 — GPIO port B bit 5 |
| Pin produk 33 | PB6 — GPIO port B bit 6 |
| Pin produk 34 | PB7 — GPIO port B bit 7 |
| Pin produk 35 | PC0/CANRX — GPIO port C bit 0 / CAN receive |
| Pin produk 36 | PC1/CANTX — GPIO port C bit 1 / CAN transmit |
| Pin produk 37 | PC2 — GPIO port C bit 2 |
| Pin produk 38 | PC3 — GPIO port C bit 3 |
| Pin produk 39 | PC4 — GPIO port C bit 4 |
| Pin produk 40 | PC5 — GPIO port C bit 5 |
| Pin produk 41 | PC6 — GPIO port C bit 6 |
| Pin produk 42 | PC7 — GPIO port C bit 7 |
| Pin produk 43 | PD0/SCI0RX — GPIO port D bit 0 / SCI0 receive |
| Pin produk 44 | PD1/SCI0TX — GPIO port D bit 1 / SCI0 transmit |
| Pin produk 45 | PD2/SPI0SCK — GPIO port D bit 2 / SPI0 clock |
| Pin produk 46 | PD3/SPI0MOSI — GPIO port D bit 3 / SPI0 MOSI |
| Pin produk 47 | PD4/SPI0MISO — GPIO port D bit 4 / SPI0 MISO |
| Pin produk 48 | PD5/SPI0SS — GPIO port D bit 5 / SPI0 slave select |
| Pin produk 49 | PE0/TIM0 — GPIO port E bit 0 / Timer channel 0 |
| Pin produk 50 | PE1/TIM1 — GPIO port E bit 1 / Timer channel 1 |
| Pin produk 51 | PE2/TIM2 — GPIO port E bit 2 / Timer channel 2 |
| Pin produk 52 | PE3/TIM3 — GPIO port E bit 3 / Timer channel 3 |
Aplikasi Umum
MC9S12C128MPBE cocok untuk 6 aplikasis: Automotive Body Controller, HVAC Control Module, Industrial CAN Node, Instrument Cluster Sub-Controller, Legacy HC11 Migration Target, Battery Management Slave Module.
Automotive Body Controller
The MC9S12C128MPBE is purpose-built for automotive body controllers such as door modules, seat controllers, mirror adjusters, and lighting nodes. Its 25 MHz CPU12 core and 128 KB Flash handle the layered state-machine logic typical of body control firmware, while the integrated msCAN module talks directly to the vehicle CAN bus at up to 1 Mbit/s without an external transceiver controller. The -40C to +125C automotive temperature grade and 52-LQFP footprint meet the thermal and PCB-area requirements of underhood and cabin ECUs. Compared with an 8-bit HC11, the HCS12 core offers roughly 3-5x more throughput per MHz, freeing headroom for LIN sub-bus management, PWM-driven mirror/glass actuators, and OBD-II diagnostics in a single chip. Recommend pairing the MCU with NXP TJA1042 CAN transceivers and TLE4271 supply rails.
Direkomendasikan
HVAC Control Module
HVAC control modules for automotive cabins benefit from the MC9S12C128MPBE's combination of a 10-bit multi-channel ADC, enhanced capture timer (ECT), and CAN connectivity in a 52-LQFP package sized for compact dashboard-mounted PCBAs. The ADC digitizes thermistor inputs from cabin, evaporator, and outside-air sensors with adequate resolution for closed-loop temperature control, while the ECT generates the PWM outputs that drive blower fans and mode doors. The 128 KB Flash accommodates lookup-table-driven control algorithms and self-test routines, and 4 KB of RAM is sufficient for sensor filtering and CAN message buffering. The automotive temperature grade and on-chip voltage regulator simplify the bill of materials. Recommend pairing with NXP MM912J637 sensor interface ICs for rotary HVAC knob decoding.
Direkomendasikan
Industrial CAN Node
For industrial CANopen or DeviceNet slave nodes, the MC9S12C128MPBE offers a compelling combination of 16-bit performance, 128 KB Flash for CANopen stack libraries, and a hardware CAN 2.0A/B controller. The 52-LQFP (10x10 mm) footprint fits inside IP65 node housings and the -40C to +125C temperature range tolerates cabinet and outdoor environments. The BDM debug interface accelerates firmware bring-up, while the SCI (UART) and SPI peripherals support local sensor and actuator expansion. Estimated firmware footprint for a typical CANopen CiA 401 generic I/O profile plus stack is 40-60 KB, well within the 128 KB Flash budget. Recommend pairing with isolated CAN transceivers such as ADM3053 for industrial bus isolation.
Direkomendasikan
Instrument Cluster Sub-Controller
Distributed instrument cluster architectures use the MC9S12C128MPBE as a sub-controller that drives gauges, indicator LEDs, and warning buzzers while communicating with the main cluster MCU over CAN. The 25 MHz CPU12 core is fast enough to multiplex multiple gauge stepper motors and refresh indicator states at 100+ Hz without visible flicker, and the 128 KB Flash stores gauge calibration tables. The 52-LQFP package footprint and on-chip PWM/timer channels minimize external driver count. The automotive temperature grade supports behind-dash thermal environments. Recommend pairing with NXP MC33932 stepper motor driver H-bridges for analog gauge actuation.
Direkomendasikan
Legacy HC11 Migration Target
Designers maintaining legacy HC11-based products can migrate to the MC9S12C128MPBE for a 3-5x performance boost while keeping the CPU instruction set and development environment similar enough to reuse most firmware. The S12C family shares the HC11 programming model and adds 128 KB Flash (vs typical 32-60 KB on HC11), 4 KB RAM, and modern peripherals including msCAN. The 52-LQFP package is pin-compatible with the HC11 in many of the same footprints, enabling PCB reuse. Recommend a BDM-based firmware port using NXP CodeWarrior and validating the new peripheral interrupt vector table against the HC11 source.
Direkomendasikan
Battery Management Slave Module
Battery management systems (BMS) for 12V/48V automotive batteries use the MC9S12C128MPBE as a cell-monitoring slave that reads ADC channels, performs local calculations, and reports results over CAN. The 10-bit ADC and 25 MHz core provide sufficient performance for cell-voltage sampling at 1 kHz, and the 128 KB Flash stores cell-balancing tables and safety state machines. The -40C to +125C temperature range tolerates underhood battery placement, and the 52-LQFP package supports compact BMS PCBAs. Recommend pairing with NXP MC33771B battery cell controller ICs for the analog front-end and isolated CAN transceivers for the high-voltage isolation boundary.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MC9S12C128MPBE — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MC9S12C128CPBE | MC9S12GC128MPBE | MC9S12C128VPBE | MC9S12C96VPBE | MC9S12C64MPB |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 52-LQFP (10x10 mm) | 52-LQFP (10x10 mm) - same | 52-LQFP (10x10 mm) - same | 52-LQFP (10x10 mm) - same | 52-LQFP (10x10 mm) - same | 52-LQFP (10x10 mm) - same |
| Core | HCS12 (CPU12) | HCS12 (CPU12) | HCS12 (CPU12) | HCS12 (CPU12) | HCS12 (CPU12) | HCS12 (CPU12) |
| Maximum Clock Frequency | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
| Flash Memory | 128 KB | 128 KB | 128 KB | 128 KB | 96 KB | 64 KB |
| RAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| Operating Temperature | -40C to +125C (automotive) | 0C to +70C (commercial) | -40C to +125C (automotive) | -40C to +125C (extended) | -40C to +125C | -40C to +125C (automotive) |
| CAN Module | msCAN (CAN 2.0A/B) | msCAN | msCAN | msCAN | msCAN | msCAN |
Diferensiator Kunci
- Automotive-grade temperature range in 52-LQFP (vsMC9S12C128CPBE)
- Enhanced peripheral set of S12GC sub-family (vsMC9S12C128VPBE)
- Larger Flash budget vs lower-cost variants (vsMC9S12C64MPB)
Catatan Desain
The MC9S12C128MPBE includes an on-chip voltage regulator that derives the internal logic supply from a single external 5V rail. Place a 100nF decoupling capacitor on every VDD/VSS pin pair, plus a bulk 4.7uF-10uF tantalum or ceramic on the VDDR (pin 2) regulator input. The regulator can source the internal core plus moderate GPIO loads but cannot drive external high-current peripherals - use a discrete 5V LDO such as the TLE4271-2 for external loads.
Do not float the BKGD/MODC pin (pin 1) - it is used for background debug mode entry at reset and must be tied through a resistor network or left for the BDM tool. Floating this pin can cause unexpected reset vector behavior. Per the NXP S12C reference manual, the recommended BDM circuit includes a pull-up to VDDR and a series resistor to the debugger. Also ensure the TEST pin (pin 7) is tied directly to VSS - leaving it floating or pulled high places the device into factory test mode.
Route the CAN bus differential pair (PC0/CANRX and PC1/CANTX) as a 100-ohm differential pair with controlled impedance, keeping total stub length under 10mm. Place the CAN transceiver (e.g., TJA1042T) within 50mm of the MCU pins to minimize EMI susceptibility. The EXTAL/XTAL oscillator traces should be short, surrounded by a ground guard ring, and isolated from noisy switching signals to avoid jitter on the 25 MHz bus clock. Decoupling capacitors must be placed within 3mm of their respective VDD pins.
Informasi Konformitas
Automotive temperature grade per 'M' suffix in NXP ordering scheme. AEC-Q100 qualification expected for automotive-grade S12C family members per NXP product page. Halogen-free status not explicitly confirmed in provided data.
