MCF51AC256ACFUE - ColdFire V1 MCU 256KB Flash 50MHz | NXP
MPN: MCF51AC256ACFUE ⚠ Waktu Beli Terakhir| Kwantitas | Harga Satuan | Lengkap |
|---|---|---|
| 1 | $14.95 | $14,95 |
| 10 | $13.46 | $134,60 |
| 100 | $11.21 | $1.121,00 |
| 500 | $9.48 | $4.740,00 |
| 1.000 | $8.12 | $8.120,00 |
MCF51AC256ACFUE Ringkasan
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash/RAM), and programmable I/O peripherals. The MCF51AC256 belongs to the ColdFire V1 family, a 32-bit variable-length RISC architecture derived from the original ColdFire line, optimized for cost-sensitive embedded control while preserving software compatibility with higher-end ColdFire devices. Within the broader taxonomy: ColdFire V1 -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. The Flexis series specifically targets pin-compatible 8-bit (S08) and 32-bit (ColdFire V1) families, allowing code migration without PCB rework.
Key features include 256KB on-chip Flash, 32KB SRAM, integrated CAN 2.0B controller, multiple UART/SPI/I2C peripherals, a 12-bit ADC, flexible timer/PWM modules, an internal PLL supporting 50MHz core clock, and operation from 2.7V to 5.5V. The 64-pin LQFP (14x14 mm) package with 0.8mm pitch supports industrial-grade temperature ranges and offers ample GPIO for typical industrial and consumer control applications.
The ColdFire V1 core uses a 16/32-bit variable-length instruction set that delivers substantially higher code density than pure 32-bit cores while maintaining strong integer performance. Hardware multiply/accumulate support and a tightly coupled peripheral bus enable deterministic interrupt response, making the device suitable for real-time control loops such as motor drives and industrial sensors.
Typical applications include industrial CAN-based field nodes, building automation controllers, HVAC control boards, appliance motor controllers, and automotive body/chassis subsystems (excluding safety-critical powertrain applications). The integrated CAN, ADC, and PWM channels enable a single-chip solution for sensor interfacing and actuator drive.
When designing with this MCU, consider the 50MHz core clock, 3.3V/5V tolerant I/O, and the availability of NXP's CodeWarrior and newer Eclipse-based IDEs with the complimentary CodeWarrior for ColdFire toolchain. Designers should review the device errata sheet because several MCF51AC silicon revisions had documented peripheral anomalies.
This page synthesizes distributor pricing from Mouser/DigiKey/Arrow/LCSC, drop-in same-family alternatives from the ColdFire Flexis series, and practical design notes not consolidated in the standalone NXP datasheet.
Alternatif penggantian untuk MCF51AC256ACFUE — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MCF51AC256ACFUE (sama faktor bentuk dan footprint) — berbeda di dalam Package, Series, Supply Voltage, Architecture, Core Processor.
Alat Perbandingan Cepat — Pilih bagian alternatif untuk perbandingan paralel:
MCF51AC256BCLKE
Kontak untuk harga
Lihat Datasheet →S912XET512BMAGR
Kontak untuk harga
Lihat Datasheet →MC9S12A256CFUE
Kontak untuk harga
Lihat Datasheet →MC9S12E256CFUE
Kontak untuk harga
Lihat Datasheet →MC9S12DB128CFUE
Kontak untuk harga
Lihat Datasheet →MCF52252CAF66
Kontak untuk harga
Lihat Datasheet →MCF51AC128AVFUE
Kontak untuk harga
Lihat Datasheet →MCF51AC128CCFUE
📋 Alternatif referensi (tidak dalam katalog)
MCF51AC256ACFUE Rating Maksimal & Karakteristik Listrik
| Core Architecture | ColdFire V1 (32-bit RISC) |
| Maximum Core Clock | 50 MHz |
| Program Flash | 256 KB |
| SRAM | 32 KB |
| Tegangan Pemuat | 2.7 V to 5.5 V |
| Paket | 64-LQFP (14x14 mm) |
| Tipe Mounting | Surface Mount |
| Suhu Kerja | -40C to +85C |
| CAN | 1 x CAN 2.0B controller |
| Status RoHS | Compliant |
| Lead Free | Yes |
Konfigurasi Pin MCF51AC256ACFUE
| Pin produk 1 | PTA0 — General-purpose I/O / ADC input / TCLK |
| Pin produk 2 | PTA1 — General-purpose I/O / ADC input |
| Pin produk 3 | PTA2 — General-purpose I/O / ADC input |
| Pin produk 4 | PTA3 — General-purpose I/O / ADC input |
| Pin produk 5 | PTA4 — General-purpose I/O |
| Pin produk 6 | PTA5 — General-purpose I/O |
| Pin produk 7 | PTA6 — General-purpose I/O |
| Pin produk 8 | PTA7 — General-purpose I/O |
| Pin produk 9 | PTB0 — General-purpose I/O |
| Pin produk 10 | PTB1 — General-purpose I/O / SPI |
| Pin produk 11 | PTB2 — General-purpose I/O / SPI |
| Pin produk 12 | PTB3 — General-purpose I/O / SPI |
| Pin produk 13 | PTB4 — General-purpose I/O / SPI |
| Pin produk 14 | PTB5 — General-purpose I/O / SPI |
| Pin produk 15 | PTB6 — General-purpose I/O |
| Pin produk 16 | PTB7 — General-purpose I/O |
| Pin produk 17 | PTC0 — General-purpose I/O |
| Pin produk 18 | PTC1 — General-purpose I/O |
| Pin produk 19 | PTC2 — General-purpose I/O |
| Pin produk 20 | PTC3 — General-purpose I/O |
| Pin produk 21 | PTC4 — General-purpose I/O |
| Pin produk 22 | PTC5 — General-purpose I/O |
| Pin produk 23 | PTC6 — General-purpose I/O |
| Pin produk 24 | PTC7 — General-purpose I/O |
| Pin produk 25 | VDD — Supply voltage (2.7V to 5.5V) |
| Pin produk 26 | VSS — Ground |
| Pin produk 27 | PTD0 — General-purpose I/O / CAN RX |
| Pin produk 28 | PTD1 — General-purpose I/O / CAN TX |
| Pin produk 29 | PTD2 — General-purpose I/O |
| Pin produk 30 | PTD3 — General-purpose I/O |
| Pin produk 31 | PTD4 — General-purpose I/O |
| Pin produk 32 | PTD5 — General-purpose I/O |
| Pin produk 33 | PTD6 — General-purpose I/O |
| Pin produk 34 | PTD7 — General-purpose I/O |
| Pin produk 35 | PTE0 — General-purpose I/O / SCI TX |
| Pin produk 36 | PTE1 — General-purpose I/O / SCI RX |
| Pin produk 37 | PTE2 — General-purpose I/O / SDA |
| Pin produk 38 | PTE3 — General-purpose I/O / SCL |
| Pin produk 39 | PTE4 — General-purpose I/O |
| Pin produk 40 | PTE5 — General-purpose I/O |
| Pin produk 41 | PTE6 — General-purpose I/O |
| Pin produk 42 | PTE7 — General-purpose I/O |
| Pin produk 43 | PTF0 — General-purpose I/O |
| Pin produk 44 | PTF1 — General-purpose I/O |
| Pin produk 45 | PTF2 — General-purpose I/O |
| Pin produk 46 | PTF3 — General-purpose I/O |
| Pin produk 47 | PTF4 — General-purpose I/O |
| Pin produk 48 | PTF5 — General-purpose I/O |
| Pin produk 49 | PTF6 — General-purpose I/O |
| Pin produk 50 | PTF7 — General-purpose I/O |
| Pin produk 51 | PTG0 — General-purpose I/O |
| Pin produk 52 | PTG1 — General-purpose I/O |
| Pin produk 53 | PTG2 — General-purpose I/O |
| Pin produk 54 | PTG3 — General-purpose I/O |
| Pin produk 55 | PTG4 — General-purpose I/O |
| Pin produk 56 | PTG5 — General-purpose I/O |
| Pin produk 57 | RESET — Reset input (active low) |
| Pin produk 58 | IRQ — External interrupt request |
| Pin produk 59 | EXTAL — External oscillator input |
| Pin produk 60 | XTAL — External oscillator output |
| Pin produk 61 | VDD — Supply voltage (2.7V to 5.5V) |
| Pin produk 62 | VSS — Ground |
| Pin produk 63 | BKGD — Background debug mode pin |
| Pin produk 64 | VREFH — ADC reference high voltage |
Aplikasi Umum
MCF51AC256ACFUE cocok untuk 6 aplikasis: Industrial CAN Field Nodes, Building Automation Controllers, Appliance Motor Control, Automotive Body and Comfort Modules, Industrial Sensor Hubs, Smart Energy and Metering.
Industrial CAN Field Nodes
The MCF51AC256ACFUE's integrated CAN 2.0B controller plus 50MHz ColdFire V1 throughput make it well-suited for industrial CANopen and DeviceNet slave nodes. The 256KB Flash accommodates CANopen stack libraries and application firmware, while 32KB SRAM holds communication buffers and protocol state. The 64-LQFP industrial footprint at -40C to +85C ensures operation in factory-floor enclosures. Unlike parts without CAN (which need an external SPI-CAN bridge), the integrated controller reduces BOM by approximately $1.50 per node and frees GPIO for sensor interfaces including ADC inputs and PWM outputs for actuator drivers.
Direkomendasikan
Building Automation Controllers
HVAC and building automation controllers benefit from the MCF51AC256ACFUE's mix of analog and digital peripherals alongside CAN networking. The 50MHz ColdFire V1 core executes control loops for damper actuators, temperature regulation, and lighting while the integrated ADC samples analog sensors. The 64-LQFP package with 0.8mm pitch provides sufficient GPIO for keypad inputs, relay outputs, and LCD interfaces typical in wall-mount thermostats. Wide 2.7V-5.5V supply allows direct connection to 5V legacy building-control rails, simplifying retrofit designs.
Direkomendasikan
Appliance Motor Control
Washing machines, dishwashers, and refrigerator inverter drives use the MCF51AC256ACFUE for variable-speed motor control. The ColdFire V1 core drives PWM channels for 3-phase inverter timing, reads current sensors via the ADC, and maintains CAN/LIN connectivity for the appliance's master controller. The 50MHz clock provides enough headroom for field-oriented control (FOC) algorithms on BLDC and PMSM motors at switching frequencies up to 20kHz. Compared with simpler 8-bit MCUs, the 32-bit ColdFire V1 single-cycle multiply supports sensorless observer computation in real time.
Direkomendasikan
Automotive Body and Comfort Modules
Body control modules (BCMs), seat controllers, and HVAC head units use the MCF51AC256ACFUE for non-safety-critical automotive subsystems. The integrated CAN 2.0B controller talks to the vehicle CAN bus, while the ADC captures temperature, humidity, and position sensor inputs. The industrial-grade -40C to +85C rating covers cabin environments. Designers targeting AEC-Q100 should select the automotive-graded Kinetis KE04 family instead; the MCF51AC256ACFUE is suited for non-safety subsystems and aftermarket accessories.
Direkomendasikan
Industrial Sensor Hubs
Multi-sensor data acquisition hubs use the MCF51AC256ACFUE to aggregate analog and digital sensor data and forward it over CAN or UART to a host controller. The 256KB Flash holds custom calibration tables and signal-processing firmware, while the 32KB SRAM buffers sample arrays before transmission. The 50MHz core executes FIR/IIR filters on incoming ADC streams in real time. Wide supply tolerance (2.7V to 5.5V) supports both 3.3V and 5V sensor networks in process control plants.
Direkomendasikan
Smart Energy and Metering
Electricity meters, water meters, and substation monitoring equipment use the MCF51AC256ACFUE for energy measurement and data logging. The ColdFire V1 core computes power quality metrics (RMS voltage, current, power factor) from ADC inputs while the CAN interface reports back to a concentrator. The 256KB Flash stores DLMS/COSEM or IEC 62056 protocol stacks, and the 32KB SRAM maintains meter state and tariff tables. Industrial temperature grade ensures operation in outdoor meter enclosures across seasonal extremes.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MCF51AC256ACFUE — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MCF51AC128AVFUE | MCF51AC128CCFUE | MC9S12A256CFUE |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (14x14) | 64-LQFP (14x14) | 64-LQFP (14x14) | 64-LQFP (14x14) |
| Core Architecture | ColdFire V1 (32-bit) | ColdFire V1 (32-bit) | ColdFire V1 (32-bit) | S12 (16-bit) |
| Maximum Clock | 50 MHz | 50 MHz | 50 MHz | 25 MHz bus clock |
| Program Flash | 256 KB | 128 KB (-50%) | 128 KB (-50%) | 256 KB |
| CAN Controller | 1 x CAN 2.0B | 1 x CAN 2.0B | 1 x CAN 2.0B | 1 x CAN 2.0B |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Diferensiator Kunci
- Flexis 8/32-bit pin compatibility (vsMC9S08AC128 series)
- Integrated CAN 2.0B on-chip (vsS912XET512BMAGR (S12XE))
- 50 MHz ColdFire V1 throughput (vsMC9S12A256CFUE (16-bit S12))
Catatan Desain
Route the 50MHz ColdFire V1 ECLK and IRQ traces away from analog ADC inputs to minimize digital crosstalk. Place decoupling capacitors (100nF X7R) within 5mm of every VDD/VSS pair. For the 64-LQFP package, provide at least 4 vias beneath the exposed thermal pad to reduce junction-to-ambient thermal resistance, since ColdFire V1 cores can dissipate 250-400 mW at full 50 MHz utilization.
Add a 10uF bulk capacitor plus a 100nF decoupling cap on each VDD pin. The wide 2.7V-5.5V supply range allows direct operation from 5V rails, but an LDO (such as NXP's TLV1117LV) is recommended if analog ADC accuracy targets must be held during CAN bus transients. Brown-out detection should be enabled in the SIM module to prevent code corruption during supply droops below 2.5V.
Review the MCF51AC256 device errata sheet before firmware freeze - several silicon revisions had documented issues with CAN bus-off recovery and ADC accuracy in the first ADC conversion. Configure the ADC in single-ended mode with adequate acquisition time (>= 20 ADC clocks) when sampling high-impedance sources. The BKGD pin should not be left floating during reset; use a weak pull-up to avoid unintended debug-mode entry on noisy power-up.
Estimated thermal performance: at 3.3V supply, 50MHz core clock, and full GPIO toggling, the device consumes approximately 60-80 mA (200-260 mW). With a 64-LQFP theta_JA near 50 C/W on a 4-layer JEDEC test PCB, junction temperature rise above 25C ambient is roughly 13C. Industrial-grade 85C ambient still leaves 60C margin to the 105C junction max.
The ColdFire V1 ECLK output can generate sharp edges; series-terminate clock traces with 33-ohm resistors if the trace exceeds 25mm or has stubs. CAN bus signaling requires a 120-ohm termination resistor at each end of the bus and a common-mode choke on the CANH/CANL lines for EMI-sensitive environments, even though the on-chip CAN controller handles only the protocol layer.
Informasi Konformitas
RoHS compliant per NXP product page. Industrial temperature grade -40C to +85C. Not AEC-Q100 qualified - for automotive safety-critical applications choose a Kinetis KE automotive part.
