MCP3302T-BI/SL - 13-Bit Dual-Channel ADC | Microchip
MPN: MCP3302T-BI/SL ✓ AktifMCP3302T-BI/SL Ringkasan
An ADC is a semiconductor that converts an analog voltage into a digital number for processing by a microcontroller or other digital system. The MCP3302 belongs to the successive-approximation ADC hierarchy, which uses an internal sample-and-hold circuit, comparator, and successive conversion process. Its differential inputs support measurement of voltage differences, while the SPI interface allows a host processor to retrieve conversion results through a compact, serial connection.
Key features include 13-bit resolution, two simultaneous-looking analog input channels, four selectable analog inputs, 100 kSPS sampling performance, and a 4.5 V to 5.5 V analog supply range. The four-input architecture allows two channels to be configured as differential inputs or as four single-ended channels. This flexibility supports bridge sensors, ratiometric measurements, potentiometer sensing, and multiple analog signals sharing one converter.
The MCP3302 uses a serial peripheral interface compatible with the industry-standard SPI framing used by Microchip's related MCP3301 family. A microcontroller can issue a conversion command, wait for the indicated conversion interval, and read the 13-bit result through the serial data and clock lines. Differential operation reduces common-mode sensitivity when the measured signal is small relative to the voltage referenced by the converter.
Typical applications include industrial process-control modules, battery-powered remote sensors, laboratory measurement equipment, environmental monitors, and compact control boards. The low-power operating environment and small SOIC footprint are useful where board area and energy use are constrained. Designers should also account for analog-reference quality, input settling time, source impedance, and PCB layout when establishing conversion accuracy.
For reliable operation, bypass the analog supply close to the device and route analog and digital return currents separately. Reference and signal traces should remain short, with analog ground arranged to minimize voltage drops caused by digital output currents. Input-driver settling must be checked against the converter's sampling network, especially when multiplexed sensors have high output impedance.
This product page combines the manufacturer specifications, verified distributor listings, package information, replacement analysis, and application-focused engineering guidance. It also distinguishes a true pin-compatible alternative from broader functional ADC options, helping designers evaluate PCB reuse, interface continuity, resolution, conversion rate, and supply requirements before approving a substitution.
Alternatif penggantian untuk MCP3302T-BI/SL — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MCP3302T-BI/SL (sama faktor bentuk dan footprint) — berbeda di dalam Input Type.
MCP3302-BI/SL
✅ Drop-InKontak untuk harga
Lihat Datasheet →MCP3302T-BI/SL Rating Maksimal & Karakteristik Listrik
| Resolusi | 13 bit |
| Converter Type | Successive-approximation (SAR) ADC |
| Number of Channels | 2 channels |
| Input Configuration | 4 differential or single-ended inputs |
| Input Type | Differential and single-ended |
| Laju Pengambilan Sampel | 100 kSPS |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Digital Interface | SPI serial interface |
| Paket | 14-pin SOIC |
| Tipe Mounting | Surface mount |
| Jumlah Pin | 14 pins |
| Output Code | 13-bit ADC result |
MCP3302T-BI/SL 14-pin soic Diamant Konfigurasi Panduan
Konfigurasi pin untuk MCP3302T-BI/SL (14-pin soic pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk MCP3302T-BI/SL.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MCP3302T-BI/SL cocok untuk 6 aplikasis: Industrial Process Measurement, Battery-Powered Remote Sensor Nodes, Environmental Monitoring, Laboratory Instrumentation, Battery Charger and Power-System Monitoring, Precision Digital Potentiometer Readback.
Industrial Process Measurement
The MCP3302T-BI/SL fits industrial process-control modules that monitor pressure, temperature, flow, or level signals with a 4.5 V to 5.5 V supply. Its 13-bit resolution and 100 kSPS rate support responsive conversion of slowly changing process variables, while differential inputs help reject common-mode voltage present on long sensor wiring. The 14-pin SOIC package also keeps the converter compact for multi-channel controller boards. Designers should use the differential configuration when the sensor output is centered around a nonzero reference voltage and should verify input range, settling behavior, and isolation requirements at the connector.
Direkomendasikan
Battery-Powered Remote Sensor Nodes
The MCP3302T-BI/SL is appropriate for battery-powered remote sensor nodes where analog measurements must be captured without a continuous high-power conversion load. Microchip positions the MCP3302 family for battery-operated systems, and the 100 kSPS conversion rate supports periodic sensing as well as moderate-rate monitoring. Two channels and four selectable inputs allow a node to combine two differential measurements or monitor four single-ended sensors. Duty-cycling the converter and placing it on a switched low-power rail can reduce average energy use, provided the host controller and sensor drivers preserve the required acquisition timing.
Direkomendasikan
Environmental Monitoring
The MCP3302T-BI/SL can digitize outputs from temperature, humidity, gas, and soil-moisture sensors in compact environmental monitoring equipment. The 13-bit result format provides useful resolution for slow-changing environmental variables, and the selectable differential or single-ended input architecture simplifies boards that mix ratiometric and grounded sensor outputs. At 100 kSPS, the converter is considerably faster than typical environmental sensing needs, allowing the firmware to group multiple channels into one acquisition cycle. Input protection, filtering, and sensor excitation noise should be evaluated separately from ADC resolution.
Direkomendasikan
Laboratory Instrumentation
The MCP3302T-BI/SL suits compact laboratory instruments that need accurate, repeatable capture of low-level analog measurements. Its 13-bit resolution and differential-input capability are useful for amplifier outputs, potentiometers, bridge sensors, and calibrated reference voltages, while the 100 kSPS rate supports faster sweeps than many conventional panel meters require. The SPI interface allows a microcontroller to perform control functions and communicate results to a host computer. For precision measurement, engineers should evaluate the reference implementation, input leakage, noise performance, and printed-board cleanliness rather than relying on nominal resolution alone.
Direkomendasikan
Battery Charger and Power-System Monitoring
The MCP3302T-BI/SL can monitor voltages in battery-management and power-conversion systems where the designer needs a compact secondary measurement channel. The 4.5 V to 5.5 V operating range is suitable for systems with a regulated 5 V control rail, and the converter can observe individual cell or divider-derived voltages when those signals remain within the permitted input range. Differential operation supports measurements referenced to a nonzero midpoint, while the 13-bit resolution provides useful visibility into gradual changes. Protection, scaling, and isolation should be added as appropriate because the ADC is not a standalone high-voltage measurement front end.
Direkomendasikan
Precision Digital Potentiometer Readback
The MCP3302T-BI/SL can read back the wiper voltage of a digital potentiometer when system designers require confirmation of an analog setting. Two ADC channels allow one channel to measure a potentiometer position while the other monitors a reference or calibration point, and the 100 kSPS rate supports faster closed-loop adjustment than many slow user-interface systems require. Differential input operation can reduce sensitivity to common-mode supply variation when the wiper voltage is referenced to one end of the network. Input impedance, settling time, and the source resistance of the potentiometer must be checked against the acquisition network.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MCP3302T-BI/SL — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MCP3302-BI/SL |
|---|---|---|
| Package | 14-pin SOIC | 14-pin SOIC |
| Brand | Microchip Technology | Microchip Technology |
| Resolution | 13 bit | 13 bit |
| Converter Architecture | Successive-approximation (SAR) | Successive-approximation (SAR) |
| Sampling Rate | 100 kSPS | 100 kSPS |
| ADC Channels | 2 channels | 2 channels |
| Input Arrangement | 4 differential or single-ended inputs | 4 differential or single-ended inputs |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Serial Interface | SPI | SPI |
| Orderable Configuration Difference | T-BI/SL tape-and-reel order code | BI/SL order code; tube packing is identified in the family listing |
Diferensiator Kunci
- Direct PCB reuse within the MCP3302 family (vsMCP3302-BI/SL)
- Supports differential and single-ended measurement configurations (vsMCP3302-BI/SL)
- Combines 13-bit resolution with a 100 kSPS conversion rate (vsMCP3302-BI/SL)
Catatan Desain
Place the analog bypass capacitor directly beside the analog supply and ground pins, and keep the connection loop as small as practical. Route analog inputs away from SPI clock and data traces. Use a continuous ground plane where possible, but partition analog return paths so digital output currents do not flow beneath the reference, input, or converter area. Follow the layout shown in the manufacturer's datasheet because the internal sampling capacitor makes trace length and return-current control part of the acquisition accuracy.
Verify that each source settles to the required accuracy within the converter's acquisition interval. High-impedance sensors, long traces, protection diodes, and filtering networks can introduce leakage or settle more slowly than a low-impedance divider. Evaluate the complete source impedance and capacitance rather than checking only the sensor's nominal resistance. For differential measurements, both input branches should have similar impedance and timing so their difference does not continue changing during sampling.
Keep the 4.5 V to 5.5 V analog supply within its specified operating range and provide local high-frequency decoupling close to the device. Reference quality directly affects the conversion scale, so the reference path should avoid digital-current coupling and excessive trace resistance. If the reference is external, confirm its startup, stability, and noise behavior against the acquisition sequence. For battery systems, sequence the ADC supply and reference to prevent an unstable rail from corrupting measurements.
Do not treat the 13-bit conversion code as 13 bits of guaranteed absolute accuracy; offset error, gain error, nonlinearity, reference error, and noise can reduce real-world measurement precision. Use the manufacturer timing diagrams to determine when the result is valid after asserting the sample command. Avoid changing the input multiplexer immediately before conversion without allowing the prior conversion to finish and the new source to settle.
Informasi Konformitas
The exact suffix-specific environmental, material, and qualification declarations were not identified in the manufacturer product-page text or distributor listings. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status using the current Microchip product documentation and declarations for MCP3302T-BI/SL.