MCP6024-I/SL - 10MHz Quad R-R Op Amp | Microchip
MPN: MCP6024-I/SL ✓ AktifMCP6024-I/SL Ringkasan
An operational amplifier, or op amp, is an analog integrated circuit that uses high open-loop gain to amplify voltage differences. The MCP6024 belongs to the amplifier IC hierarchy: operational amplifier → voltage-feedback amplifier → analog signal-conditioning IC. Its rail-to-rail input and output stages permit sensing and driving signals close to the supply rails, while its CMOS implementation supports low bias current, high-speed operation, and low power consumption.
Key features include a 10 MHz gain-bandwidth product, 8.7 nV/√Hz input-voltage noise, maximum input offset voltage of 250 µV, and 0.00053% THD+N. The device operates from 2.5 V to 5.5 V, supports a typical output current of 30 mA, and includes four amplifiers in one 14-pin SOIC. Rail-to-rail operation is particularly useful when the usable signal range extends near either supply rail.
Microchip's advanced CMOS process provides high open-loop gain, low input bias current, and a rail-to-rail output swing. These characteristics make the quad amplifier suitable for general-purpose signal conditioning, where four independent channels can reduce package count on mixed-signal boards. The 1.0 mA typical operating-current specification supports portable and low-power equipment, although actual current varies with supply voltage, load, channel activity, and operating temperature.
Typical uses include sensor conditioning, battery-powered instrumentation, ADC input drivers, audio preamplification, filter stages, and general voltage amplification. In each channel, the amplifier can be configured as a non-inverting or inverting amplifier, or as part of an active filter. The quad organization makes the MCP6024 especially useful when a board needs several amplifiers with similar electrical performance.
When laying out a design, place input, output, supply, and decoupling connections according to the manufacturer's pinout and recommended circuit. Account for output-current limits when driving heavier loads, and verify stability with the selected gain, feedback network, capacitive load, and supply bypassing. The -I grade is intended for an industrial temperature range of -40°C to +85°C.
This page combines manufacturer specifications, package details, sourcing guidance, application analysis, and a qualified drop-in comparison. It helps engineers distinguish temperature-grade alternatives from merely similar amplifiers and focus on the electrical and packaging details that determine PCB compatibility.
Alternatif penggantian untuk MCP6024-I/SL — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
MCP6024-E/SL
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MCP6024-I/SL Rating Maksimal & Karakteristik Listrik
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 4 circuits |
| Gain-Bandwidth Product | 10 MHz |
| Typical Operating Current | 1.0 mA |
| Typical Input Offset Voltage | <0.5 mV |
| Maximum Input Offset Voltage | 250 µV |
| Input Voltage Noise Density | 8.7 nV/√Hz |
| Total Harmonic Distortion Plus Noise | 0.00053% |
| Supply Voltage Range | 2.5 V to 5.5 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Voltage Swing | Rail-to-rail |
| Typical Output Current | 30 mA |
| Rentang Suhu Kerja | -40°C to +85°C |
| Paket | 14-pin SOIC, 0.150 inch |
| Tipe Mounting | Surface mount |
| Automotive Qualification | AEC-Q100 |
Konfigurasi Pin MCP6024-I/SL
| Pin produk 1 | OUTA — Amplifier A output |
| Pin produk 2 | INA- — Amplifier A inverting input |
| Pin produk 3 | INA+ — Amplifier A non-inverting input |
| Pin produk 4 | V- — Negative supply or ground connection |
| Pin produk 5 | INB+ — Amplifier B non-inverting input |
| Pin produk 6 | INB- — Amplifier B inverting input |
| Pin produk 7 | OUTB — Amplifier B output |
| Pin produk 8 | OUTC — Amplifier C output |
| Pin produk 9 | V+ — Positive supply connection |
| Pin produk 10 | INC- — Amplifier C inverting input |
| Pin produk 11 | INC+ — Amplifier C non-inverting input |
| Pin produk 12 | OUTD — Amplifier D output |
| Pin produk 13 | IND- — Amplifier D inverting input |
| Pin produk 14 | IND+ — Amplifier D non-inverting input |
Aplikasi Umum
MCP6024-I/SL cocok untuk 6 aplikasis: Battery-Powered Sensor Conditioning, ADC Input Buffering, Active Filter and Signal Conditioning, Audio Preamplification, Industrial Control and Instrumentation, Portable and Low-Power Measurement.
Battery-Powered Sensor Conditioning
The MCP6024-I/SL suits low-voltage sensor front ends where four channels can condition related inputs without using separate amplifier packages. Rail-to-rail input operation allows the amplifier to sense signals near the lower or upper end of a 2.5 V to 5.5 V supply, while the 1.0 mA typical operating current helps limit power demand in portable equipment. Its 10 MHz gain-bandwidth product provides useful bandwidth for common resistive sensors and low-rate data-acquisition paths. The principal design consideration is verifying source impedance, output swing, and noise requirements before selecting the gain and feedback network.
Direkomendasikan
ADC Input Buffering
The MCP6024-I/SL can provide four independent buffers or gain stages ahead of an ADC, helping isolate the converter from sensor and switching-node loading. Its rail-to-rail input and output behavior makes it useful with low-voltage ADC input ranges, while 10 MHz bandwidth accommodates signal paths that require settling beyond the sampled bandwidth. The 8.7 nV/√Hz noise density and 250 µV maximum offset voltage are useful starting points for precision budgeting. Confirm the ADC acquisition time, input capacitance, settling accuracy, and output-current requirement for the selected channel configuration.
Direkomendasikan
Active Filter and Signal Conditioning
The MCP6024-I/SL is appropriate for building active low-pass, high-pass, or multi-stage analog filters where four repeated channels simplify layout and reduce component count. The 10 MHz gain-bandwidth product provides ample closed-loop bandwidth for many low-frequency sensor and audio-conditioning stages, while the low 8.7 nV/√Hz input-noise density supports quiet signal paths. Designers should calculate gain-bandwidth, noise-gain stability, resistor tolerance, and capacitor selection for each filter. The same SOIC can house unrelated filter sections, provided each amplifier remains within its output swing and drive limits.
Direkomendasikan
Audio Preamplification
The MCP6024-I/SL can implement four small-signal audio preamplifier or line-stage channels when a design requires rail-to-rail operation and a 10 MHz gain-bandwidth product. Its 0.00053% THD+N specification is useful for low-distortion signal paths, and the quad package permits consistent channel implementation in audio interface boards. The amplifier still requires careful source impedance, gain, bandwidth, and output-loading analysis. Avoid assuming that the specified THD+N applies at every frequency, load, supply voltage, and gain; check the manufacturer test conditions for the operating point used in the design.
Direkomendasikan
Industrial Control and Instrumentation
The MCP6024-I/SL is a practical fit for industrial control and instrumentation boards that require several general-purpose analog channels around a low-voltage controller. Its -40°C to +85°C grade covers the specified industrial temperature range, while the 2.5 V to 5.5 V supply operation supports common embedded control rails. The four amplifiers can implement buffering, gain, level shifting, or impedance conversion around sensors and actuators. Industrial designs should still account for transient protection, grounding, diagnostic behavior, and the amplifier's maximum output-current limitation independently of normal signal amplitude.
Direkomendasikan
Portable and Low-Power Measurement
The MCP6024-I/SL supports portable measurement equipment where four analog channels, rail-to-rail operation, and low typical operating current are useful together. A 2.5 V to 5.5 V supply enables operation from compact battery rails, and the 10 MHz gain-bandwidth product permits moderately high-bandwidth measurement stages. The 8.7 nV/√Hz noise density is helpful when evaluating weak sensor outputs, although resistor-network noise and reference accuracy may dominate. Minimize leakage into high-impedance sources and select capacitor and resistor types carefully to prevent board-level leakage from overwhelming the amplifier's own input characteristics.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MCP6024-I/SL — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MCP6024-E/SL |
|---|---|---|
| Package | 14-SOIC | 14-SOIC |
| Brand | Microchip Technology | Microchip Technology |
| Number of Amplifiers | 4 circuits | 4 circuits |
| Gain-Bandwidth Product | 10 MHz | 10 MHz |
| Supply Voltage Range | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
| Maximum Input Offset Voltage | 250 µV | 250 µV |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Operating Temperature Range | -40°C to +85°C | -40°C to +125°C |
| Input Noise Density | 8.7 nV/√Hz | 8.7 nV/√Hz |
Diferensiator Kunci
- Extended-temperature drop-in option (vsMCP6024-E/SL)
- Four rail-to-rail amplifier channels in one package (vsMCP6024-E/SL)
- Low-power CMOS operation (vsMCP6024-E/SL)
Catatan Desain
Place the input, output, and supply bypass connections directly adjacent to their corresponding SOIC pins. Keep each amplifier's feedback components close to the relevant input and output pins to minimize parasitic inductance and feedback-loop area. Connect the V+ and V- pins to short, low-impedance supply paths, and provide local high-frequency decoupling according to the manufacturer's recommended circuit. Avoid routing sensitive input traces beneath or immediately beside switching-node and digital-return paths.
Verify output loading against the 30 mA typical output-current capability and preserve the 2.5 V to 5.5 V supply range. Rail-to-rail input and output operation does not guarantee unlimited input range, output drive, or stable operation with every capacitive load. Check the feedback configuration, load impedance, supply decoupling, and expected signal amplitude at temperature. Use the MCP6024-E/SL instead when the enclosure can exceed the MCP6024-I/SL upper temperature limit of +85°C.
Check settling accuracy rather than relying only on the 10 MHz gain-bandwidth product. The required settling time depends on closed-loop gain, target accuracy, load, and the effective bandwidth of the selected feedback network. For high-impedance sensors, minimize leakage from board contamination and adjacent digital inputs, and use guarded routing where appropriate. Also evaluate the 8.7 nV/√Hz input-noise density together with resistor noise and reference accuracy at the circuit level.
Do not treat every MCP6024 ordering suffix as a direct replacement. MCP6024T-I/SL changes the packing form, MCP6024-I/P changes the package, and MCP6024-E/SL changes the temperature grade. Compare the manufacturer's ordering information, package drawing, pinout, and electrical limits before substitution. In a four-channel design, also verify that each unused amplifier is configured in a stable state rather than left with an open input.
Informasi Konformitas
The distributor product listing identifies the MCP6024-I/SL as AEC-Q100 automotive qualified. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established from the cited manufacturer or distributor information.