MCP602T-E/SN - Dual 2.8 MHz RRO Op Amp | Microchip
MPN: MCP602T-E/SN ✓ AktifMCP602T-E/SN Ringkasan
An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, filter, compare, or control an analog signal. The MCP602 belongs to the CMOS operational-amplifier family within the broader amplifier IC and semiconductor hierarchies. Its unity-gain stability supports direct use as a non-inverting or inverting buffer without external frequency compensation.
The MCP602 combines a 2.8 MHz typical gain-bandwidth product with a 2.3 V/us slew rate. Its typical operating current is 230 uA per amplifier, while input offset voltage is less than 2 mV. Rail-to-rail output operation increases usable output range on low-voltage supplies, and the input range includes ground for circuits operating near the lower supply rail.
The E suffix identifies the specific ordering configuration, while SN denotes the 8-SOIC package used by MCP602T-E/SN. The package provides a conventional 8-pin surface-mount footprint and is suitable for compact analog boards. The dual configuration places two amplifiers in one package, reducing component count in designs requiring matched circuit functions such as filtering, buffering, or differential signal conditioning.
Typical uses include low-voltage sensor conditioning, buffered instrumentation, active filtering, audio signal paths, and general-purpose analog signal processing. The 230 uA operating current is particularly useful in portable equipment where each milliamp of continuous consumption can affect battery life. The 2.8 MHz bandwidth also supports applications requiring more bandwidth than very-low-power amplifiers while avoiding the supply current of higher-speed precision amplifiers.
Design the circuit around the 2.7 V minimum supply and confirm the input and output voltages remain within the operating ranges specified by the manufacturer. Decoupling capacitors should be placed close to the supply pins, and feedback-network components should be selected to preserve the required gain-bandwidth and phase margin. For sensitive analog signals, resistor noise, offset error, and input bias current must be considered alongside the amplifier's stated performance.
Alternatif penggantian untuk MCP602T-E/SN — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MCP602T-E/SN (sama faktor bentuk dan footprint) — berbeda di dalam Package, Typical Operating Current, Gain-Bandwidth Product, Mounting Type, Amplifier Type.
MCP602T-I/SN
✅ Drop-InKontak untuk harga
Lihat Datasheet →MCP602-E/SN
✅ Drop-InKontak untuk harga
Lihat Datasheet →MCP602T-E/ST
✅ Drop-InKontak untuk harga
Lihat Datasheet →MCP6023T-I/SN
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MCP6002T-E/SN
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MCP602T-E/SN Rating Maksimal & Karakteristik Listrik
| Amplifier Type | General-purpose CMOS operational amplifier |
| Number of Circuits | 2 circuits |
| Gain-Bandwidth Product | 2.8 MHz typical |
| Slew Rate | 2.3 V/us typical |
| Typical Operating Current | 230 uA per amplifier typical |
| Input Offset Voltage | Less than 2 mV typical |
| Single-Supply Voltage Range | 2.7 V to 6.0 V |
| Output Swing | Rail-to-rail |
| Input Common-Mode Range | Includes ground |
| Gain Configuration | Unity-gain stable |
| Technology | CMOS |
| Paket | 8-SOIC, 0.154 inch / 3.90 mm body width |
| Tipe Mounting | Surface mount |
| Packaging | Tape and reel |
Konfigurasi Pin MCP602T-E/SN
| Pin produk 1 | OUTA — Amplifier A output |
| Pin produk 2 | INA- — Inverting input of amplifier A |
| Pin produk 3 | INA+ — Non-inverting input of amplifier A |
| Pin produk 4 | V- — Negative supply or ground |
| Pin produk 5 | INB+ — Non-inverting input of amplifier B |
| Pin produk 6 | INB- — Inverting input of amplifier B |
| Pin produk 7 | OUTB — Amplifier B output |
| Pin produk 8 | V+ — Positive supply |
Aplikasi Umum
MCP602T-E/SN cocok untuk 6 aplikasis: Low-Voltage Sensor Signal Conditioning, Portable Audio Buffering, Active Analog Filtering, Industrial Control Signal Interface, Precision Data Acquisition Front End, Battery-Powered Monitoring Circuit.
Low-Voltage Sensor Signal Conditioning
The MCP602T-E/SN is well suited to conditioning sensor outputs on 2.7 V to 6.0 V supplies because its input range includes ground and its output can swing rail-to-rail. Two independent amplifiers in one 8-SOIC package can amplify or buffer two channels without requiring separate packages. The 2.8 MHz typical gain-bandwidth product provides more signal-path bandwidth than a very-low-speed amplifier, while the 230 uA typical operating current per channel limits the continuous burden in portable or distributed sensing systems. Engineers should still calculate the actual source impedance, bias-current error, offset contribution, and filter bandwidth for the selected sensor.
Direkomendasikan
Portable Audio Buffering
The MCP602T-E/SN can buffer low-level audio or microphone signals when system power is limited to a 2.7 V to 6.0 V rail. Its rail-to-rail output swing helps preserve signal amplitude near the supply limits, and the 2.8 MHz typical gain-bandwidth product is suitable for many speech, control, and general audio-conditioning paths. The dual configuration allows one channel to perform an active filter while the other buffers a related signal. The 2.3 V/us typical slew rate should be checked against large-signal requirements, while input bias current and noise determine suitability for high-impedance microphones.
Direkomendasikan
Active Analog Filtering
The dual MCP602T-E/SN supports active filter, integrator, and signal-shaping circuits where two amplifier stages are required. Its 2.8 MHz typical gain-bandwidth product provides useful loop gain for moderate-frequency active filters, and its unity-gain stability supports straightforward voltage-follower configurations. Because closed-loop bandwidth depends on the selected noise gain, filter capacitor and resistor tolerances directly influence cutoff frequency and Q. The 230 uA typical operating current per amplifier makes the device relevant to compact, low-power analog modules, but each feedback node should be checked for stability with the final component values.
Direkomendasikan
Industrial Control Signal Interface
The MCP602T-E/SN can interface low-level control and monitoring signals in compact industrial equipment operating from a 3.3 V or 5 V rail. Its input range that includes ground supports signals referenced to the lower supply rail, while rail-to-rail output swing helps drive ADC front ends, comparator inputs, or downstream control stages. The dual 8-SOIC arrangement reduces board area by combining two common analog functions. Industrial suitability still depends on the selected temperature grade, electromagnetic environment, isolation strategy, and quality requirements, so the exact ordering suffix and operating limits must be checked before release.
Direkomendasikan
Precision Data Acquisition Front End
The MCP602T-E/SN can serve as a low-noise buffering and gain stage ahead of a data-conversion system requiring a compact dual amplifier. Its less-than-2 mV typical input offset, 2.8 MHz typical gain-bandwidth product, and unity-gain stability make it appropriate for sensor and instrumentation paths with moderate bandwidth requirements. The two channels can provide independent acquisition channels or differential conditioning stages. Design review should compare the amplifier's offset, input bias current, noise density, and output capability with the ADC's input range and settling requirements, particularly when the source impedance is high.
Direkomendasikan
Battery-Powered Monitoring Circuit
The MCP602T-E/SN is appropriate for battery-powered monitoring modules because it operates down to a 2.7 V single supply and draws 230 uA per amplifier typically. The low-power CMOS implementation supports longer operating intervals when the monitored signal does not require continuous high-bandwidth amplification. A dual device can combine a sensing amplifier with a buffer, comparator, or active-filter stage in one package. Actual battery life depends on supply voltage, duty cycle, leakage, output loading, and whether either channel can be disabled, so the final power budget must use measured or worst-case operating-current conditions.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MCP602T-E/SN — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MCP602T-I/SN | MCP602-E/SN | MCP602T-E/ST | MCP6023T-I/SN | MCP6002T-E/SN |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Number of Amplifiers | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
Diferensiator Kunci
- Higher bandwidth than the MCP6002 general-purpose alternative (vsMCP6002T-E/SN)
- Same-family electrical configuration with an industrial ordering option (vsMCP602T-I/SN)
- Low-noise dual-channel integration in a standard package (vsMCP6023T-I/SN)
Catatan Desain
Decouple the positive supply and ground pins with short, low-inductance connections to the closest available ground plane. Place the input, output, and feedback paths away from the supply traces and switching nodes. The MCP602 can operate down to 2.7 V, but the usable output amplitude and common-mode range still depend on the actual supply voltage. Verify headroom at the highest and lowest signal levels rather than assuming the full rail-to-rail designation leaves no saturation margin.
Keep each feedback resistor and capacitor immediately adjacent to its amplifier input and output pins. This minimizes parasitic capacitance in the feedback loop and helps preserve phase margin at the 2.8 MHz typical gain-bandwidth product. Route both channels symmetrically when matching matters, maintain a continuous ground reference beneath the SOIC footprint, and follow the manufacturer land-pattern drawing for pad length and spacing. Avoid placing sensitive high-impedance input traces beneath noisy clocks, regulators, or digital return paths.
Do not substitute an amplifier solely because its package is 8-SOIC. Check the positive and negative supply limits, common-mode range, output swing, gain-bandwidth product, slew rate, input bias current, offset, noise, stability, and exact temperature-grade suffix before redesignating a component. The MCP602 family supports operation from 2.7 V to 6.0 V with an input range including ground, but a related low-power amplifier may have substantially lower bandwidth or different offset and bias-current behavior.
Informasi Konformitas
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was found for the exact MCP602T-E/SN ordering code. The general-purpose operational-amplifier category is not inherently automotive-qualified.