Microchip Technology

MCP602T-E/SN - Dual 2.8 MHz RRO Op Amp | Microchip

MPN: MCP602T-E/SN ✓ פעיל
Less than 2 mV typical Vdss 230 uA per amplifier typical Id 8-SOIC, 0.154 inch / 3.90 mm body width Package
כמות הזמנה מינימלית: 1 |

MCP602T-E/SN סקירה

Microchip Technology MCP602T-E/SN is a dual general-purpose operational amplifier with a 2.8 MHz gain-bandwidth product, 230 uA typical operating current per amplifier, and rail-to-rail output swing, housed in an 8-SOIC package. The device accepts a single supply from 2.7 V to 6.0 V and supports an input range that includes ground, making it suitable for low-voltage signal-processing systems.

An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, filter, compare, or control an analog signal. The MCP602 belongs to the CMOS operational-amplifier family within the broader amplifier IC and semiconductor hierarchies. Its unity-gain stability supports direct use as a non-inverting or inverting buffer without external frequency compensation.

The MCP602 combines a 2.8 MHz typical gain-bandwidth product with a 2.3 V/us slew rate. Its typical operating current is 230 uA per amplifier, while input offset voltage is less than 2 mV. Rail-to-rail output operation increases usable output range on low-voltage supplies, and the input range includes ground for circuits operating near the lower supply rail.

The E suffix identifies the specific ordering configuration, while SN denotes the 8-SOIC package used by MCP602T-E/SN. The package provides a conventional 8-pin surface-mount footprint and is suitable for compact analog boards. The dual configuration places two amplifiers in one package, reducing component count in designs requiring matched circuit functions such as filtering, buffering, or differential signal conditioning.

Typical uses include low-voltage sensor conditioning, buffered instrumentation, active filtering, audio signal paths, and general-purpose analog signal processing. The 230 uA operating current is particularly useful in portable equipment where each milliamp of continuous consumption can affect battery life. The 2.8 MHz bandwidth also supports applications requiring more bandwidth than very-low-power amplifiers while avoiding the supply current of higher-speed precision amplifiers.

Design the circuit around the 2.7 V minimum supply and confirm the input and output voltages remain within the operating ranges specified by the manufacturer. Decoupling capacitors should be placed close to the supply pins, and feedback-network components should be selected to preserve the required gain-bandwidth and phase margin. For sensitive analog signals, resistor noise, offset error, and input bias current must be considered alongside the amplifier's stated performance.

חלופות תחליף ישיר עבור MCP602T-E/SN — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם MCP602T-E/SN (אותו גורם צורה וטביעת רגל) — שונים ב Package, Typical Operating Current, Gain-Bandwidth Product, Mounting Type, Amplifier Type.

Microchip Technology
Package: 8-pin SOIC, 0.154 in and 3.90 mm width
Typical Operating Current: 230 uA per amplifier
Mounting Type: Surface-mount
Microchip Technology
Package: 8-pin TSSOP
Typical Operating Current: 230 uA
Gain-Bandwidth Product: 2.8 MHz
Microchip Technology
Package: 8-pin SOIC
Typical Operating Current: 230 uA per amplifier
Gain-Bandwidth Product: 2.8 MHz

MCP602T-I/SN

✅ Drop-In
Microchip Technology
📦 8-SOIC
2 amplifiers · 2.8 MHz · 230 uA per amplifier · Less than 2 mV · 2.7 V to 6.0 V · CMOS · Rail-to-rail · Low bias current

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MCP602-E/SN

✅ Drop-In
Microchip Technology
📦 8-SOIC
General-purpose operational amplifier · 2 circuits · CMOS · 2.7 V to 6.0 V · 2.8 MHz typical · 2.3 V/us typical · 230 uA per amplifier · Less than 2 mV

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MCP602T-E/ST

✅ Drop-In
Microchip Technology
📦 8-SOIC
General-purpose CMOS operational amplifier · 2 channels · 2.8 MHz · 230 uA · <2 mV · 2.7 V to 6.0 V · Rail-to-rail

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MCP6023T-I/SN

✅ Drop-In
📦 8-SOIC
Related MCP602x dual CMOS family in 8-SOIC; detailed gain-bandwidth, slew-rate, offset, and input-bias differences require comparison against the manufacturer datasheet

📋 חלופה להתייחסות (לא בקטלוג)

MCP6002T-E/SN

✅ Drop-In
📦 8-SOIC
Same dual general-purpose rail-to-rail 8-SOIC class, but the MCP6002 family has lower gain bandwidth than the MCP602's 2.8 MHz typical value

📋 חלופה להתייחסות (לא בקטלוג)

MCP602T-E/SN דירוגים מרביים ומאפיינים חשמליים

Amplifier Type General-purpose CMOS operational amplifier
Number of Circuits 2 circuits
Gain-Bandwidth Product 2.8 MHz typical
Slew Rate 2.3 V/us typical
Typical Operating Current 230 uA per amplifier typical
Input Offset Voltage Less than 2 mV typical
Single-Supply Voltage Range 2.7 V to 6.0 V
Output Swing Rail-to-rail
Input Common-Mode Range Includes ground
Gain Configuration Unity-gain stable
Technology CMOS
מארז 8-SOIC, 0.154 inch / 3.90 mm body width
סוג הרכבה Surface mount
Packaging Tape and reel

תצורת פינים של MCP602T-E/SN

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
פין 1 OUTA — Amplifier A output
פין 2 INA- — Inverting input of amplifier A
פין 3 INA+ — Non-inverting input of amplifier A
פין 4 V- — Negative supply or ground
פין 5 INB+ — Non-inverting input of amplifier B
פין 6 INB- — Inverting input of amplifier B
פין 7 OUTB — Amplifier B output
פין 8 V+ — Positive supply

יישומים טיפוסיים

MCP602T-E/SN מתאים עבור 6 יישוםs: Low-Voltage Sensor Signal Conditioning, Portable Audio Buffering, Active Analog Filtering, Industrial Control Signal Interface, Precision Data Acquisition Front End, Battery-Powered Monitoring Circuit.

🧩

Low-Voltage Sensor Signal Conditioning

The MCP602T-E/SN is well suited to conditioning sensor outputs on 2.7 V to 6.0 V supplies because its input range includes ground and its output can swing rail-to-rail. Two independent amplifiers in one 8-SOIC package can amplify or buffer two channels without requiring separate packages. The 2.8 MHz typical gain-bandwidth product provides more signal-path bandwidth than a very-low-speed amplifier, while the 230 uA typical operating current per channel limits the continuous burden in portable or distributed sensing systems. Engineers should still calculate the actual source impedance, bias-current error, offset contribution, and filter bandwidth for the selected sensor.

🎧

Portable Audio Buffering

The MCP602T-E/SN can buffer low-level audio or microphone signals when system power is limited to a 2.7 V to 6.0 V rail. Its rail-to-rail output swing helps preserve signal amplitude near the supply limits, and the 2.8 MHz typical gain-bandwidth product is suitable for many speech, control, and general audio-conditioning paths. The dual configuration allows one channel to perform an active filter while the other buffers a related signal. The 2.3 V/us typical slew rate should be checked against large-signal requirements, while input bias current and noise determine suitability for high-impedance microphones.

⚡

Active Analog Filtering

The dual MCP602T-E/SN supports active filter, integrator, and signal-shaping circuits where two amplifier stages are required. Its 2.8 MHz typical gain-bandwidth product provides useful loop gain for moderate-frequency active filters, and its unity-gain stability supports straightforward voltage-follower configurations. Because closed-loop bandwidth depends on the selected noise gain, filter capacitor and resistor tolerances directly influence cutoff frequency and Q. The 230 uA typical operating current per amplifier makes the device relevant to compact, low-power analog modules, but each feedback node should be checked for stability with the final component values.

🏭

Industrial Control Signal Interface

The MCP602T-E/SN can interface low-level control and monitoring signals in compact industrial equipment operating from a 3.3 V or 5 V rail. Its input range that includes ground supports signals referenced to the lower supply rail, while rail-to-rail output swing helps drive ADC front ends, comparator inputs, or downstream control stages. The dual 8-SOIC arrangement reduces board area by combining two common analog functions. Industrial suitability still depends on the selected temperature grade, electromagnetic environment, isolation strategy, and quality requirements, so the exact ordering suffix and operating limits must be checked before release.

🖥️

Precision Data Acquisition Front End

The MCP602T-E/SN can serve as a low-noise buffering and gain stage ahead of a data-conversion system requiring a compact dual amplifier. Its less-than-2 mV typical input offset, 2.8 MHz typical gain-bandwidth product, and unity-gain stability make it appropriate for sensor and instrumentation paths with moderate bandwidth requirements. The two channels can provide independent acquisition channels or differential conditioning stages. Design review should compare the amplifier's offset, input bias current, noise density, and output capability with the ADC's input range and settling requirements, particularly when the source impedance is high.

📱

Battery-Powered Monitoring Circuit

The MCP602T-E/SN is appropriate for battery-powered monitoring modules because it operates down to a 2.7 V single supply and draws 230 uA per amplifier typically. The low-power CMOS implementation supports longer operating intervals when the monitored signal does not require continuous high-bandwidth amplification. A dual device can combine a sensing amplifier with a buffer, comparator, or active-filter stage in one package. Actual battery life depends on supply voltage, duty cycle, leakage, output loading, and whether either channel can be disabled, so the final power budget must use measured or worst-case operating-current conditions.

What are the key specifications of MCP602T-E/SN that engineers should know?
The MCP602T-E/SN is a dual, general-purpose CMOS operational amplifier with a 2.8 MHz typical gain-bandwidth product, 2.3 V/us typical slew rate, 230 uA typical operating current per amplifier, and less than 2 mV typical input offset voltage. According to the Microchip Technology MCP602 product page, it uses advanced CMOS technology, while the MCP602 family documentation identifies rail-to-rail output operation, unity-gain stability, and an input range that includes ground. The device is supplied in an 8-SOIC package for standard surface-mount assembly.
What is the operating voltage range of MCP602T-E/SN?
The MCP602T-E/SN operates from a 2.7 V to 6.0 V single supply. This range allows the dual amplifier to be used in low-voltage systems while supporting conventional 3.3 V and 5 V rails. According to the Microchip Technology MCP602 documentation, the amplifier also supports an input common-mode range that includes ground and provides rail-to-rail output swing. Confirm signal amplitudes and output requirements against the electrical characteristics in the manufacturer datasheet before finalizing the circuit.
Where can I download the MCP602T-E/SN datasheet PDF?
The official MCP602 datasheet and product information are available through the Microchip Technology MCP602 product page at https://www.microchip.com/en-us/product/MCP602. The MCP602T-E/SN is the E-temperature ordering configuration in the SN 8-SOIC package. Use the manufacturer document as the primary source for the pin description, electrical limits, recommended operating conditions, and package drawings before beginning PCB layout or qualification.
Where can I find the MCP602T-E/SN pinout?
The MCP602T-E/SN pinout is shown in the manufacturer datasheet and the 8-SOIC package drawing. The dual amplifier uses eight pins: two outputs, four input pins, one positive supply, and one negative or ground supply. The pin-description table in the Microchip Technology MCP602 documentation is the authoritative reference for board design. Use the package drawing and pin table together so that pin 1 orientation, exposed-body details, and PCB pad placement remain consistent.
What is the gain-bandwidth product of MCP602T-E/SN?
The MCP602T-E/SN has a typical gain-bandwidth product of 2.8 MHz. This specification describes the approximate closed-bandwidth relationship between amplifier gain and frequency for a compensated operational amplifier. According to the Microchip Technology MCP602 product page, the device is unity-gain stable, allowing direct voltage-follower use without external compensation. At higher closed-loop gains, the usable bandwidth will be lower, and stability should be checked with the actual feedback network.
Is MCP602T-E/SN suitable for low-voltage sensor conditioning?
Yes, the MCP602T-E/SN is suitable for low-voltage sensor conditioning because it operates from 2.7 V to 6.0 V, consumes 230 uA per amplifier typically, and includes ground in its input range. Its less-than-2 mV typical offset can also be relevant when conditioning low-level sensor signals. According to the Microchip Technology MCP602 documentation, the amplifier provides rail-to-rail output swing and unity-gain stability. Sensor-specific accuracy should still be checked against source impedance, bias current, noise, and the required measurement bandwidth.
How much current does MCP602T-E/SN consume?
The MCP602T-E/SN consumes 230 uA per amplifier typically, or about 460 uA for both amplifiers when each channel operates under the typical conditions cited for the device. According to the Microchip Technology MCP602 product page, this low operating current supports power-conscious analog designs. Actual supply current depends on supply voltage, input voltage, output swing, channel activity, and the test conditions used for characterization; use the manufacturer electrical characteristics for worst-case design calculations.
MCP602T-E/SN vs MCP602T-I/SN - which is better?
MCP602T-E/SN is the better choice when the design requires the E-grade ordering configuration and an 8-SOIC package, while MCP602T-I/SN is the industrial-temperature ordering option in the same family and package. The Microchip Technology MCP602 product page identifies both as members of the MCP602 dual-op-amp family with a 2.8 MHz typical gain-bandwidth product and 230 uA typical operating current per amplifier. The temperature-grade distinction should be the deciding factor after confirming the exact ordering suffix and environmental requirements.
What is the difference between MCP602T-E/SN and MCP6002T-E/SN?
The principal difference is the MCP602 family's 2.8 MHz gain-bandwidth product, compared with the lower-bandwidth MCP6002 general-purpose amplifier identified as a dual rail-to-rail 8-SOIC alternative. Both families are low-power CMOS dual operational amplifiers, so their basic packaging and signal-conditioning roles are related. According to the Microchip Technology MCP602 documentation, MCP602 also has a 2.3 V/us typical slew rate. Choose by checking gain bandwidth, slew rate, offset, input bias current, noise, and stability against the actual signal requirements.
When should I choose MCP602T-E/SN over MCP6002T-E/SN?
Choose MCP602T-E/SN when the signal path requires the higher 2.8 MHz gain-bandwidth product and 2.3 V/us slew rate of the MCP602 family. MCP6002T-E/SN may be considered when its lower-bandwidth characteristics are sufficient and the design prioritizes a related low-power dual CMOS amplifier in an 8-SOIC package. According to the Microchip Technology MCP602 product page, the MCP602 offers less-than-2 mV typical offset and 230 uA typical operating current per amplifier. Confirm all parameters in the manufacturer datasheet before finalizing the choice.
What can replace MCP602T-E/SN on the same 8-SOIC footprint?
MCP602T-E/SN can be replaced only after confirming electrical and environmental equivalence, not merely package shape. MCP602T-I/SN is a closely related same-family alternative in 8-SOIC, while MCP602-E/SN and MCP602T-E/ST represent other ordering configurations that require temperature-grade and marking review. The manufacturer family and comparison pages identify the MCP602 family characteristics of 2.8 MHz typical gain-bandwidth product and 230 uA typical operating current per amplifier. Confirm pin functions, supply range, offset, noise, slew rate, and qualification requirements before substitution.
What is the best Microchip drop-in replacement for MCP602T-E/SN?
MCP602T-I/SN is the closest same-family choice identified for MCP602T-E/SN because it uses the same 8-SOIC format and belongs to the MCP602 dual operational-amplifier family. The Microchip Technology MCP602 product page gives the family gain-bandwidth product as 2.8 MHz and typical operating current as 230 uA per amplifier. The I ordering suffix may be selected for a different temperature grade, so engineers should verify that grade against the target circuit's environmental requirements rather than treating all suffix differences as interchangeable.
Is MCP602T-E/SN the same as MCP602T-I/SN?
No. MCP602T-E/SN and MCP602T-I/SN are related 8-SOIC devices in the MCP602 dual-op-amp family, but their ordering suffixes identify different temperature-grade configurations. Both are associated with the family's 2.8 MHz typical gain-bandwidth product and 230 uA typical operating current per amplifier according to Microchip Technology documentation. The E designation may be appropriate where the specified operating range is adequate, while the I configuration is intended for a different temperature grade; verify the orderable part table before substitution.
Where can I buy MCP602T-E/SN online?
Use the Request a Quote form on this page to ask for MCP602T-E/SN availability, lead time, and a current quotation. The manufacturer product page identifies MCP602 as the active family, while distributor search pages carry the exact MCP602T-E/SN ordering code. Quote requests help confirm the required package, temperature suffix, delivery quantity, and current lifecycle position before an order is placed. The same form can also be used when sourcing production quantities or checking scheduled allocations.
What is the price of MCP602T-E/SN?
Request a current MCP602T-E/SN quotation through the Request a Quote form on this page. Pricing is structured separately from the technical description because market price, quantity, delivery timing, and sourcing conditions can change. The form allows the exact MPN, package, and required quantity to be confirmed before an order is committed. Engineers should also verify the manufacturer ordering information and any authorized-channel terms applicable to their procurement process.
What is the lead time and stock status for MCP602T-E/SN?
Request current stock status, minimum order quantity, and lead time through the Request a Quote form on this page. The Microchip Technology MCP602 product page identifies the MCP602 family, but current channel inventory and production scheduling should be confirmed for the exact MCP602T-E/SN ordering code. Include your required quantity and target delivery date in the request so the commercial response reflects the actual build plan rather than a generic availability statement.

נתוני עזר הנדסיים עבור MCP602T-E/SN — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose MCP602T-E/SN when the design needs a low-power dual CMOS op amp with a 2.8 MHz typical gain-bandwidth product, 2.3 V/us typical slew rate, an input range that includes ground, and rail-to-rail output operation from a 2.7 V to 6.0 V supply. MCP602T-I/SN is the closest same-family choice when its temperature grade matches the product requirements. MCP602-E/SN and MCP602T-E/ST require attention to ordering, marking, and environmental differences even though they remain in the 8-SOIC family. MCP6023T-I/SN may be considered after its electrical characteristics are verified against the complete signal chain. MCP6002T-E/SN is the lower-bandwidth option and should be selected only when its gain bandwidth, offset, noise, bias current, and slew rate meet the application. For every replacement, confirm pin functions, supply limits, stability, and qualification requirements rather than relying on package compatibility alone.

השוואה עם חלופות

פרמטר מוצר זה MCP602T-I/SN MCP602-E/SN MCP602T-E/ST MCP6023T-I/SN MCP6002T-E/SN
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Number of Amplifiers 2 circuits 2 circuits 2 circuits 2 circuits 2 circuits 2 circuits

מבדילים עיקריים

  • Higher bandwidth than the MCP6002 general-purpose alternative (לעומתMCP6002T-E/SN)
  • Same-family electrical configuration with an industrial ordering option (לעומתMCP602T-I/SN)
  • Low-noise dual-channel integration in a standard package (לעומתMCP6023T-I/SN)

הערות תכנון

Decouple the positive supply and ground pins with short, low-inductance connections to the closest available ground plane. Place the input, output, and feedback paths away from the supply traces and switching nodes. The MCP602 can operate down to 2.7 V, but the usable output amplitude and common-mode range still depend on the actual supply voltage. Verify headroom at the highest and lowest signal levels rather than assuming the full rail-to-rail designation leaves no saturation margin.

Keep each feedback resistor and capacitor immediately adjacent to its amplifier input and output pins. This minimizes parasitic capacitance in the feedback loop and helps preserve phase margin at the 2.8 MHz typical gain-bandwidth product. Route both channels symmetrically when matching matters, maintain a continuous ground reference beneath the SOIC footprint, and follow the manufacturer land-pattern drawing for pad length and spacing. Avoid placing sensitive high-impedance input traces beneath noisy clocks, regulators, or digital return paths.

Do not substitute an amplifier solely because its package is 8-SOIC. Check the positive and negative supply limits, common-mode range, output swing, gain-bandwidth product, slew rate, input bias current, offset, noise, stability, and exact temperature-grade suffix before redesignating a component. The MCP602 family supports operation from 2.7 V to 6.0 V with an input range including ground, but a related low-power amplifier may have substantially lower bandwidth or different offset and bias-current behavior.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was found for the exact MCP602T-E/SN ordering code. The general-purpose operational-amplifier category is not inherently automotive-qualified.

הנתונים אומתו בתאריך: 2026-11-20 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

mcp602t i sn datasheet MCP602T-E/SN datasheet MCP602T-E/SN pinout MCP602T-E/SN datasheet pdf MCP602T-E/SN equivalent MCP602T-E/SN replacement MCP602T-E/SN vs MCP602T-I/SN MCP602T-E/SN vs MCP6002T-E/SN Microchip MCP602T-E/SN MCP602T-E/SN 8-SOIC footprint MCP602T-E/SN sensor conditioning MCP602T-E/SN price MCP602T-E/SN stock MCP602T-E/SN application circuit

רכיבים ומונחים קשורים

Microchip Technology MCP602T-E/SN MCP602T-I/SN MCP602-E/SN MCP602T-E/ST MCP6023T-I/SN MCP6002T-E/SN MCP602 operational amplifier dual op amp CMOS operational amplifier amplifier IC analog signal conditioning gain-bandwidth product slew rate input offset voltage input bias current rail-to-rail output unity-gain stable 8-SOIC surface mount sensor conditioning active filter data acquisition
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר