Microchip Technology

MCP6041-I/MS - 14 kHz Low-Power Rail-to-Rail Op Amp | Microchip

MPN: MCP6041-I/MS ✓ Aktif
<3 mV Vdss 600 nA Id 8-MSOP Package
MOQ: 1 |

MCP6041-I/MS Ringkasan

Microchip Technology MCP6041-I/MS is a single-amplifier CMOS operational amplifier with a 14 kHz gain-bandwidth product, typical operating current of 600 nA, and rail-to-rail input and output operation. The device is offered in an 8-MSOP package and operates from a 1.6 V single supply according to the product listing, making it suitable for compact, low-voltage signal-conditioning circuits.

An operational amplifier, commonly called an op amp, is an amplifier IC that uses high open-loop gain to amplify small voltage differences. When configured with external feedback resistors, it can form voltage amplifiers, buffers, comparators, transimpedance amplifiers, and active filters. The MCP6041 belongs to the low-power operational-amplifier category within the broader hierarchy of amplifier ICs and analog semiconductors.

The principal features are a 14 kHz gain-bandwidth product, 600 nA typical operating current, an offset voltage below 3 mV, and rail-to-rail input and output capability. Low operating current reduces the burden on battery-powered and energy-harvesting systems, while rail-to-rail operation improves signal range in low-voltage designs where the useful input and output levels extend close to the supply rails.

Microchip's CMOS implementation supports low power consumption and low input bias current. A 14 kHz gain-bandwidth product is adequate for slow sensor signals, instrumentation signals, audio-frequency control loops, and general buffering rather than high-speed waveform or communications paths. Designers should account for the bandwidth when selecting closed-loop gain because operating gain reduces the available signal bandwidth.

Typical uses include portable sensor interfaces, low-power filter stages, battery-operated monitors, audio input conditioning, and low-voltage actuator feedback loops. The MCP6041 can also function as a unity-gain buffer when the source and load conditions permit stable operation. Its low current draw is especially useful when the amplifier must remain continuously powered in a compact embedded system.

For PCB implementation, place the amplifier close to the feedback and decoupling components, route high-impedance input nodes with minimal exposed area, and provide a local bypass capacitor near the supply pins. Confirm output-swing limits and input common-mode behavior against the actual supply voltage before designing near the rails.

This product page consolidates the manufacturer's core specifications, package information, sourcing paths, drop-in alternatives, and application-focused design guidance. It also compares the MCP6041-I/MS with compatible family members so engineers can evaluate temperature grade, bandwidth, packaging, and signal-chain requirements before finalizing a BOM.

Alternatif penggantian untuk MCP6041-I/MS — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian MCP6041-I/MS (sama faktor bentuk dan footprint) — berbeda di dalam Amplifier Type, Input Common-Mode Range, Input Offset Voltage, Number of Channels, Output Swing.

Microchip Technology
Amplifier Type: General-purpose operational amplifier
Input Common-Mode Range: Rail-to-rail input
Input Offset Voltage: Less than 3 mV

MCP6041-E/MS

✅ Drop-In
📦 8-MSOP
Extended-temperature ordering grade replaces the industrial-grade suffix; the 14 kHz bandwidth, single-amplifier architecture, and 8-MSOP footprint remain the same.

📋 Alternatif referensi (tidak dalam katalog)

MCP6041T-I/MS

✅ Drop-In
📦 8-MSOP
Temperature-grade suffix is I/MS with a T ordering identifier; key electrical ratings remain in the same MCP6041 family, though final ordering details must be verified.

📋 Alternatif referensi (tidak dalam katalog)

MCP6042-I/MS

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
Microchip Technology
📦 8-MSOP
General-purpose operational amplifier · 2 channels · 14 kHz · 3 V/µs · 600 nA per amplifier · 1 pA typical · Less than 3 mV · 1.4 V to 5.5 V

Kontak untuk harga

Lihat Datasheet →

MCP6041-I/MS Rating Maksimal & Karakteristik Listrik

Amplifier Type Single general-purpose operational amplifier
Number of Channels 1 circuit
Gain-Bandwidth Product 14 kHz
Typical Operating Current 600 nA
Input Offset Voltage <3 mV
Minimum Listed Supply Voltage 1.6 V
Family Minimum Supply Voltage 1.4 V
Supply Configuration Single supply
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Technology CMOS
Paket 8-MSOP
Package Dimensions 3 mm x 3 mm
Tipe Mounting Surface mount

MCP6041-I/MS 3 mm x 3 mm Diamant Konfigurasi Panduan

Konfigurasi pin untuk MCP6041-I/MS (3 mm x 3 mm pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.

Diamant diagram pakai pakai 3 mm x 3 mm untuk MCP6041-I/MS

Tidak ada data diatribut pin yang tersedia untuk MCP6041-I/MS.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

MCP6041-I/MS cocok untuk 6 aplikasis: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Sensor Interface, Low-Power Audio Preamplifier, IoT Edge Signal Buffer, Precision Current-to-Voltage Conversion.

📱

Battery-Powered Sensor Conditioning

The MCP6041-I/MS fits low-energy sensor interfaces because its typical operating current is 600 nA and its family supports single supplies down to 1.4 V. The amplifier can condition a slow sensor output through non-inverting or differential gain stages while its rail-to-rail input behavior helps preserve signal range on a restricted supply. Its 14 kHz gain-bandwidth product is appropriate for temperature, pressure, and inertial sensors that change slowly compared with the amplifier bandwidth. Keep the input bias network and feedback values high enough to avoid excessive current, and verify input common-mode limits across the complete sensor output range.

💊

Portable Medical Monitoring

The MCP6041-I/MS is useful in portable monitoring equipment where every microamp contributes to battery consumption. Its 600 nA typical operating current supports long-duration operation, while rail-to-rail input and output behavior allows useful operation from a low single supply. The 14 kHz gain-bandwidth product is suitable for slowly varying physiological signals after appropriate filtering, and the below-3-mV typical offset specification supports low-level signal amplification. Medical applications still require system-level validation, isolation where applicable, and compliance with the relevant device-specific regulatory requirements.

🏭

Industrial Sensor Interface

The MCP6041-I/MS can serve as the first active stage in an industrial sensor interface when the source signal changes relatively slowly. Its rail-to-rail input range allows operation close to the supply limits, while the 14 kHz gain-bandwidth product provides ample response for pressure, temperature, and position sensing signals. The low 600 nA typical current also helps when the interface is distributed across many low-power sensing nodes. Designers should place input bias resistors close to the device, maintain a clean ground reference, and verify stable feedback compensation for the selected closed-loop gain.

🎧

Low-Power Audio Preamplifier

The MCP6041-I/MS can provide a low-power preamplifier or buffer for microphone-level or line-level signals in compact audio equipment. Rail-to-rail output operation supports efficient signal transfer from a low supply, while the 14 kHz gain-bandwidth product covers audio-band signals with additional margin. Its low operating current reduces battery impact compared with higher-current general-purpose amplifiers. Feedback-network impedance should be selected to control resistor-generated noise, and the input must remain within the datasheet common-mode range for the chosen supply voltage.

🧩

IoT Edge Signal Buffer

The MCP6041-I/MS is appropriate for buffering slow sensor outputs in IoT edge nodes where standby and active current are tightly constrained. Its 600 nA typical operating current minimizes amplifier contribution to system power, while the 8-MSOP package supports compact, high-density layouts. Rail-to-rail input and output characteristics provide flexibility when the node operates from a low supply and the sensor signal approaches either rail. Place the device close to the source to limit noise pickup, use a local supply bypass capacitor, and confirm that the ADC input can be driven correctly by the resulting closed-loop response.

🔧

Precision Current-to-Voltage Conversion

The MCP6041-I/MS can implement a transimpedance stage when the photodiode or sensor current is small and the required signal bandwidth remains below its 14 kHz gain-bandwidth product. Rail-to-rail output swing improves usable range on a low supply, and the low-power CMOS design suits continuously monitored systems. The feedback resistor and compensation capacitor must be selected together because parasitic input capacitance can reduce phase margin. Keep the high-impedance summing node compact, guard sensitive routing where practical, and test the complete source-load configuration across the intended output range.

What are the key specifications of MCP6041-I/MS that engineers should know?
The MCP6041-I/MS is a single, rail-to-rail CMOS operational amplifier with a 14 kHz gain-bandwidth product, 600 nA typical operating current, offset voltage below 3 mV, and an 8-MSOP package. According to the Microchip MCP6041 product page and the manufacturer datasheet, it supports single-supply operation down to 1.4 V in the family, while the MCP6041-I/MS distributor listing identifies a 1.6 V operating supply. It is intended for low-power buffering, sensor conditioning, filtering, and general-purpose analog signal processing rather than high-speed waveform applications.
Where can I download the MCP6041 datasheet PDF?
The official MCP6041 documentation is available through the Microchip product page at https://www.microchip.com/en-us/product/MCP6041. The MCP6041-I/MS product documentation covers the single-amplifier device, electrical characteristics, typical application circuits, ordering information, and package details. Use the manufacturer PDF and its pin-description table when assigning PCB tracks, selecting bypass capacitors, and confirming the operating limits for the MSOP package.
What is the gain-bandwidth product of MCP6041-I/MS?
The MCP6041-I/MS has a gain-bandwidth product of 14 kHz. According to the Microchip MCP6041 product page, this bandwidth supports general-purpose low-power signal amplification while keeping operating current at a typical 600 nA. Closed-loop bandwidth depends on the selected feedback topology, so higher noise gain reduces usable bandwidth. This specification makes the amplifier more appropriate for sensor, filtering, buffering, and slow feedback applications than for wideband signal capture.
Can MCP6041-I/MS operate from a 1.6 V single supply?
Yes, MCP6041-I/MS can operate from a 1.6 V single supply, as identified in its distributor product listing. The broader MCP6041 family supports supplies as low as 1.4 V, according to the Microchip product page. Rail-to-rail input and output operation improves usable signal swing at this low supply voltage, although the final design must still comply with the input range, output swing, and common-mode limits listed for the selected operating conditions.
What can replace MCP6041-I/MS?
MCP6041-E/MS is a directly relevant same-package replacement because it retains the MCP6041 single-amplifier architecture and 8-MSOP format while changing the temperature grade. It is the clearest drop-in choice when a higher temperature grade is acceptable. MCP6041T-I/MS can also occupy the same MSOP footprint, while MCP6042-I/MS provides a higher-bandwidth option if its gain-bandwidth difference remains acceptable for the signal chain. Confirm electrical limits, offset limits, and qualification requirements before substitution.
Is MCP6041-I/MS the same as MCP6041-E/MS?
MCP6041-I/MS and MCP6041-E/MS share the same MCP6041 family architecture and 8-MSOP package, but their temperature-grade suffixes differ. The I/MS ordering code identifies the industrial temperature option, while the E/MS ordering code identifies the extended-temperature option. They are therefore electrically and mechanically related drop-in choices when the extended-grade limits are acceptable. Review the manufacturer ordering table to confirm operating-temperature and qualification requirements for the finished equipment.
Where should I find the MCP6041-I/MS pinout?
The MCP6041-I/MS pinout is documented in the manufacturer datasheet and the ordering information associated with the official MCP6041 product page. The device is supplied in an 8-MSOP package, so the PCB footprint must match the 8-MSOP dimensions and pin numbering used by that package. Use the pin-description table when connecting the supply, bypass capacitor, non-inverting input, inverting input, and output rather than inferring connections from a generic schematic symbol.
Is MCP6041-I/MS suitable for battery-powered sensor interfaces?
The MCP6041-I/MS is well suited to battery-powered sensor interfaces because its typical operating current is only 600 nA and its family supports single-supply operation down to 1.4 V. Its rail-to-rail input behavior is useful when sensor signals occupy much of the available low-voltage range. The 14 kHz gain-bandwidth product handles slow sensor signals effectively, while the below-3-mV typical input offset specification helps limit low-level signal errors.
MCP6041-I/MS vs MCP6042-I/MS: which is better for a filtering application?
Choose MCP6041-I/MS when the 14 kHz gain-bandwidth product is sufficient and minimum power consumption is the priority. Choose MCP6042-I/MS when a faster family member is needed for a higher-bandwidth filter stage. Both are single-channel rail-to-rail CMOS amplifiers in the MCP604x family, but their gain-bandwidth characteristics differ. The correct choice depends on the filter corner frequency, closed-loop noise gain, phase margin, and acceptable power dissipation.
When should I choose MCP6041-I/MS instead of MCP6041-E/MS?
Choose MCP6041-I/MS when the product operates within the industrial temperature grade and that grade is required by the application. Choose MCP6041-E/MS when the equipment must operate across a wider temperature range and the extended-grade device meets the design requirements. Because both use the same 8-MSOP footprint, the decision should focus on temperature limits and qualification rather than PCB redesign. Verify the exact limits in the manufacturer ordering information.
What is the best Microchip equivalent for MCP6041-I/MS?
MCP6041-E/MS is the closest Microchip drop-in equivalent for applications that permit its extended temperature grade. It retains the same single-channel MCP6041 architecture and 8-MSOP package, allowing direct placement without changing the footprint. MCP6041T-I/MS is another related ordering option, while MCP6042-I/MS changes the bandwidth class. Confirm the required temperature range, electrical limits, and procurement configuration before approving any substitution.
How much current does MCP6041-I/MS consume?
MCP6041-I/MS has a typical operating current of 600 nA. According to the Microchip MCP6041 product page, the device uses advanced CMOS technology to achieve low power consumption while providing low bias current, high open-loop gain, and rail-to-rail output swing. Actual circuit consumption also includes external biasing and feedback-network current, so final battery-life calculations should include the complete analog front end rather than the amplifier current alone.
What is the lifecycle status of MCP6041-I/MS?
The Microchip MCP6041 family is presented as an active product, and MCP6041-I/MS is currently listed by major component distributors as a standard general-purpose amplifier. The manufacturer product page remains the appropriate place to confirm ordering status and any lifecycle notices. For new production designs, use the exact MPN and package suffix during BOM review so temperature-grade and packing requirements remain traceable.
Does MCP6041-I/MS meet RoHS and automotive qualification requirements?
RoHS, REACH, and AEC-Q100 status must be confirmed from the current manufacturer product documentation before treating the device as suitable for a regulated or automotive design. The MCP6041-I/MS is an industrial-grade ordering option, but the -I suffix alone does not establish AEC-Q100 qualification. Use the manufacturer material-declaration and qualification records for the exact ordering code, then apply the required organizational approval process.
Where can I request a quote and current lead time for MCP6041-I/MS?
Use the Request a Quote form on this page to request the current MCP6041-I/MS price, stock position, minimum order quantity, and production lead time. The commercial response should confirm the exact 8-MSOP ordering suffix, operating-temperature grade, and required quantity. For scheduled design-ins, request samples and production quantities together so allocation and delivery timing can be evaluated against the equipment build schedule.

Data referensi engineering untuk MCP6041-I/MS — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose MCP6041-I/MS when designing a compact, low-voltage analog front end that needs low power, rail-to-rail signal handling, and modest bandwidth. Its 600 nA typical operating current is well suited to portable sensing, and its 14 kHz gain-bandwidth product covers slow instrumentation and audio-conditioning signals. Choose MCP6041-E/MS when the same electrical architecture and footprint are needed but a wider temperature grade is required. MCP6041T-I/MS is a closely related ordering configuration that should be selected only after its ordering details are confirmed. Consider MCP6042-I/MS when the extra bandwidth of that family member is useful and its current draw, offset, and stability characteristics fit the design. For any substitution, verify supply range, common-mode limits, output swing, compensation requirements, and operating-temperature grade rather than relying on package appearance alone.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini MCP6041-E/MS MCP6041T-I/MS MCP6042-I/MS
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 8-MSOP 8-MSOP 8-MSOP 8-MSOP
Amplifier Channels 1 circuit 1 circuit 1 circuit 1 circuit
Supply Configuration Single supply Single supply Single supply Single supply

Diferensiator Kunci

  • Very low operating current supports portable analog designs (vsMCP6042-I/MS)
  • Close same-package temperature-grade alternative (vsMCP6041-E/MS)
  • Compact 8-MSOP implementation with rail-to-rail behavior (vsMCP6041T-I/MS)

Catatan Desain

Place the supply bypass capacitor directly between the amplifier's supply and ground pins, and keep the feedback resistors and compensation capacitor close to the device. For high-impedance inputs, minimize the distance from the source to the input pin and avoid routing the input beneath switching nodes or parallel to digital clock lines. A compact ground return beneath the circuit helps keep supply-current paths short and reduces susceptibility to common-impedance disturbance.

Do not assume that rail-to-rail input and output operation provides usable signal range at the exact supply rails. Check the datasheet's input common-mode and output-swing limits at the selected supply voltage, output current, and temperature. Also confirm stability at the intended closed-loop gain: the 14 kHz gain-bandwidth product is suitable for slow signals, but high noise gain can reduce bandwidth and phase margin.

Estimated: at a 1.8 V supply and 100 uA total amplifier load, the ideal supply power is 1.8 V x 100 uA = 180 uW. The actual figure also includes feedback-network current and should be checked against the datasheet operating-current conditions. Low-power designs should avoid unnecessarily low feedback resistors and should account for leakage through protection structures when operating near the supply rails.

For transimpedance and source-impedance-sensitive circuits, include the amplifier input capacitance, sensor capacitance, and PCB parasitic capacitance in stability analysis. Start with the manufacturer's typical application values, then verify the selected feedback resistor and compensation capacitor using the complete source and load model. Keep the summing node compact and provide a nearby ground reference to reduce capacitive coupling and common-mode pickup.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The industrial ordering suffix does not by itself establish AEC-Q100 qualification. Confirm material declarations and qualification status for the exact ordering code with the manufacturer.

Pencarian Terkait

mcp6041 datasheet mcp6041 pdf MCP6041-I/MS datasheet MCP6041-I/MS pinout MCP6041-I/MS equivalent MCP6041-I/MS replacement MCP6041-I/MS price MCP6041-I/MS stock MCP6041-I/MS 8-MSOP MCP6041-I/MS 14 kHz MCP6041-I/MS vs MCP6042-I/MS MCP6041-I/MS low power op amp MCP6041-I/MS footprint

Komponen dan Istilah Terkait

Microchip Technology MCP6041 MCP6041-I/MS MCP6041-E/MS MCP6041T-I/MS MCP6042-I/MS MCP6041-I/P operational amplifier op amp single amplifier low-power amplifier IC amplifier IC analog semiconductor CMOS gain-bandwidth product rail-to-rail input rail-to-rail output quiescent current input offset voltage 8-MSOP MSOP package family surface-mount package sensor conditioning transimpedance amplifier
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ