MCP6041-I/MS - 14 kHz Low-Power Rail-to-Rail Op Amp | Microchip
料号: MCP6041-I/MS ✓ 量产中MCP6041-I/MS 概述
An operational amplifier, commonly called an op amp, is an amplifier IC that uses high open-loop gain to amplify small voltage differences. When configured with external feedback resistors, it can form voltage amplifiers, buffers, comparators, transimpedance amplifiers, and active filters. The MCP6041 belongs to the low-power operational-amplifier category within the broader hierarchy of amplifier ICs and analog semiconductors.
The principal features are a 14 kHz gain-bandwidth product, 600 nA typical operating current, an offset voltage below 3 mV, and rail-to-rail input and output capability. Low operating current reduces the burden on battery-powered and energy-harvesting systems, while rail-to-rail operation improves signal range in low-voltage designs where the useful input and output levels extend close to the supply rails.
Microchip's CMOS implementation supports low power consumption and low input bias current. A 14 kHz gain-bandwidth product is adequate for slow sensor signals, instrumentation signals, audio-frequency control loops, and general buffering rather than high-speed waveform or communications paths. Designers should account for the bandwidth when selecting closed-loop gain because operating gain reduces the available signal bandwidth.
Typical uses include portable sensor interfaces, low-power filter stages, battery-operated monitors, audio input conditioning, and low-voltage actuator feedback loops. The MCP6041 can also function as a unity-gain buffer when the source and load conditions permit stable operation. Its low current draw is especially useful when the amplifier must remain continuously powered in a compact embedded system.
For PCB implementation, place the amplifier close to the feedback and decoupling components, route high-impedance input nodes with minimal exposed area, and provide a local bypass capacitor near the supply pins. Confirm output-swing limits and input common-mode behavior against the actual supply voltage before designing near the rails.
This product page consolidates the manufacturer's core specifications, package information, sourcing paths, drop-in alternatives, and application-focused design guidance. It also compares the MCP6041-I/MS with compatible family members so engineers can evaluate temperature grade, bandwidth, packaging, and signal-chain requirements before finalizing a BOM.
直接替换替代料: MCP6041-I/MS ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MCP6041-I/MS (相同外形与封装尺寸) ——差异在于 Amplifier Type, Input Common-Mode Range, Input Offset Voltage, Number of Channels, Output Swing.
MCP6041-E/MS
✅ 直接替换📋 参考替代料(不在目录中)
MCP6041T-I/MS
✅ 直接替换📋 参考替代料(不在目录中)
MCP6042-I/MS
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MCP6041-I/MS 最大额定值与电气特性
| Amplifier Type | Single general-purpose operational amplifier |
| Number of Channels | 1 circuit |
| Gain-Bandwidth Product | 14 kHz |
| Typical Operating Current | 600 nA |
| Input Offset Voltage | <3 mV |
| Minimum Listed Supply Voltage | 1.6 V |
| Family Minimum Supply Voltage | 1.4 V |
| Supply Configuration | Single supply |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Technology | CMOS |
| 封装 | 8-MSOP |
| Package Dimensions | 3 mm x 3 mm |
| 安装类型 | Surface mount |
MCP6041-I/MS 3 mm x 3 mm 引脚配置指南
MCP6041-I/MS(3 mm x 3 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: MCP6041-I/MS.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MCP6041-I/MS 适用于 6 应用s: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Sensor Interface, Low-Power Audio Preamplifier, IoT Edge Signal Buffer, Precision Current-to-Voltage Conversion.
Battery-Powered Sensor Conditioning
The MCP6041-I/MS fits low-energy sensor interfaces because its typical operating current is 600 nA and its family supports single supplies down to 1.4 V. The amplifier can condition a slow sensor output through non-inverting or differential gain stages while its rail-to-rail input behavior helps preserve signal range on a restricted supply. Its 14 kHz gain-bandwidth product is appropriate for temperature, pressure, and inertial sensors that change slowly compared with the amplifier bandwidth. Keep the input bias network and feedback values high enough to avoid excessive current, and verify input common-mode limits across the complete sensor output range.
推荐
Portable Medical Monitoring
The MCP6041-I/MS is useful in portable monitoring equipment where every microamp contributes to battery consumption. Its 600 nA typical operating current supports long-duration operation, while rail-to-rail input and output behavior allows useful operation from a low single supply. The 14 kHz gain-bandwidth product is suitable for slowly varying physiological signals after appropriate filtering, and the below-3-mV typical offset specification supports low-level signal amplification. Medical applications still require system-level validation, isolation where applicable, and compliance with the relevant device-specific regulatory requirements.
推荐
Industrial Sensor Interface
The MCP6041-I/MS can serve as the first active stage in an industrial sensor interface when the source signal changes relatively slowly. Its rail-to-rail input range allows operation close to the supply limits, while the 14 kHz gain-bandwidth product provides ample response for pressure, temperature, and position sensing signals. The low 600 nA typical current also helps when the interface is distributed across many low-power sensing nodes. Designers should place input bias resistors close to the device, maintain a clean ground reference, and verify stable feedback compensation for the selected closed-loop gain.
推荐
Low-Power Audio Preamplifier
The MCP6041-I/MS can provide a low-power preamplifier or buffer for microphone-level or line-level signals in compact audio equipment. Rail-to-rail output operation supports efficient signal transfer from a low supply, while the 14 kHz gain-bandwidth product covers audio-band signals with additional margin. Its low operating current reduces battery impact compared with higher-current general-purpose amplifiers. Feedback-network impedance should be selected to control resistor-generated noise, and the input must remain within the datasheet common-mode range for the chosen supply voltage.
推荐
IoT Edge Signal Buffer
The MCP6041-I/MS is appropriate for buffering slow sensor outputs in IoT edge nodes where standby and active current are tightly constrained. Its 600 nA typical operating current minimizes amplifier contribution to system power, while the 8-MSOP package supports compact, high-density layouts. Rail-to-rail input and output characteristics provide flexibility when the node operates from a low supply and the sensor signal approaches either rail. Place the device close to the source to limit noise pickup, use a local supply bypass capacitor, and confirm that the ADC input can be driven correctly by the resulting closed-loop response.
推荐
Precision Current-to-Voltage Conversion
The MCP6041-I/MS can implement a transimpedance stage when the photodiode or sensor current is small and the required signal bandwidth remains below its 14 kHz gain-bandwidth product. Rail-to-rail output swing improves usable range on a low supply, and the low-power CMOS design suits continuously monitored systems. The feedback resistor and compensation capacitor must be selected together because parasitic input capacitance can reduce phase margin. Keep the high-impedance summing node compact, guard sensitive routing where practical, and test the complete source-load configuration across the intended output range.
推荐
推荐产品汇总
工程参考数据: MCP6041-I/MS ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MCP6041-E/MS | MCP6041T-I/MS | MCP6042-I/MS |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-MSOP | 8-MSOP | 8-MSOP | 8-MSOP |
| Amplifier Channels | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Supply Configuration | Single supply | Single supply | Single supply | Single supply |
关键差异点
- Very low operating current supports portable analog designs (对比 MCP6042-I/MS)
- Close same-package temperature-grade alternative (对比 MCP6041-E/MS)
- Compact 8-MSOP implementation with rail-to-rail behavior (对比 MCP6041T-I/MS)
设计说明
Place the supply bypass capacitor directly between the amplifier's supply and ground pins, and keep the feedback resistors and compensation capacitor close to the device. For high-impedance inputs, minimize the distance from the source to the input pin and avoid routing the input beneath switching nodes or parallel to digital clock lines. A compact ground return beneath the circuit helps keep supply-current paths short and reduces susceptibility to common-impedance disturbance.
Do not assume that rail-to-rail input and output operation provides usable signal range at the exact supply rails. Check the datasheet's input common-mode and output-swing limits at the selected supply voltage, output current, and temperature. Also confirm stability at the intended closed-loop gain: the 14 kHz gain-bandwidth product is suitable for slow signals, but high noise gain can reduce bandwidth and phase margin.
Estimated: at a 1.8 V supply and 100 uA total amplifier load, the ideal supply power is 1.8 V x 100 uA = 180 uW. The actual figure also includes feedback-network current and should be checked against the datasheet operating-current conditions. Low-power designs should avoid unnecessarily low feedback resistors and should account for leakage through protection structures when operating near the supply rails.
For transimpedance and source-impedance-sensitive circuits, include the amplifier input capacitance, sensor capacitance, and PCB parasitic capacitance in stability analysis. Start with the manufacturer's typical application values, then verify the selected feedback resistor and compensation capacitor using the complete source and load model. Keep the summing node compact and provide a nearby ground reference to reduce capacitive coupling and common-mode pickup.
合规信息
The industrial ordering suffix does not by itself establish AEC-Q100 qualification. Confirm material declarations and qualification status for the exact ordering code with the manufacturer.