MSP430F2272IDA - 16MHz 32KB Flash Mixed-Signal MCU | TI
MPN: MSP430F2272IDA ✓ AktifMSP430F2272IDA Ringkasan
A microcontroller is a programmable semiconductor system that combines a CPU, memory, and peripherals on one integrated circuit. The MSP430F2272 belongs to the MSP430 mixed-signal microcontroller family and uses a 16-bit RISC architecture with 16-bit registers and constant generators. Its integrated analog and communications peripherals allow compact designs to measure signals, control actuators, and communicate with external sensors without requiring several separate devices.
The device operates at up to 16 MHz with a 125 ns instruction cycle time. Its 32KB Flash provides program storage, while 512B SRAM supports working memory for embedded control routines. The 10-bit ADC supports analog measurement tasks, and the I2C, SPI, and UART interfaces provide options for connecting sensors, displays, transceivers, and other digital peripherals. The five power-saving modes support duty-cycled designs where standby or off-state consumption matters.
The mixed-signal feature set makes the MSP430F2272 suitable for industrial instrumentation, sensor conditioning, portable measurement equipment, small control systems, and embedded communication nodes. The FLL+ frequency-locked loop supports controlled clock operation, while scan capability enables background instruction execution and can improve responsiveness in interrupt-driven designs.
Designers should pay close attention to the 38-pin TSSOP footprint, pin multiplexing, and the power budget of the selected operating mode. The ADC reference, communication baud rates, and firmware timing should be checked against the system clock and noise requirements. The low-power architecture is most valuable when firmware can place the MCU into a suitable standby mode during idle periods.
This product page combines manufacturer specifications, application guidance, drop-in replacement information, comparison parameters, and practical layout notes to help engineers move from component selection to a complete embedded design.
Alternatif penggantian untuk MSP430F2272IDA — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
MSP430F2272IDAR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MSP430F2272IDA Rating Maksimal & Karakteristik Listrik
| Product Type | 16-bit ultra-low-power mixed-signal microcontroller |
| CPU Architecture | 16-bit RISC MSP430 |
| Frekuensi Bawah Maximum | 16 MHz |
| Instruction Cycle Time | 125 ns |
| Flash Memory | 32KB |
| SRAM | 512B |
| ADC Resolution | 10-bit |
| Serial Interfaces | I2C, SPI, UART |
| Paket | 38-pin TSSOP (DA) |
| Power-Saving Modes | 5 modes |
| Standby Wake-Up Time | Less than 6 us |
| Clock Architecture | Frequency-Locked Loop, FLL+ |
| Register Width | 16-bit |
| Background Processing | Scan IF for background execution |
| Tipe Mounting | Surface mount |
MSP430F2272IDA 38-pin tssop (da) Diamant Konfigurasi Panduan
Konfigurasi pin untuk MSP430F2272IDA (38-pin tssop (da) pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.
Tidak ada data diatribut pin yang tersedia untuk MSP430F2272IDA.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MSP430F2272IDA cocok untuk 6 aplikasis: Industrial Sensor Measurement, Portable Environmental Monitoring, Battery-Powered Instrumentation, Digital Communication Controller, Embedded Motor and Actuator Control, Smart Home and IoT Sensor Node.
Industrial Sensor Measurement
The MSP430F2272IDA fits compact sensor-conditioning and acquisition systems because its 10-bit ADC is paired with a 16 MHz MSP430 RISC CPU, 32KB Flash, and 512B SRAM in one 38-pin TSSOP device. Firmware can sample analog channels, apply calibration and filtering, and store operational data locally before forwarding results through I2C, SPI, or UART. The mixed-signal integration reduces the need for separate interface circuitry and helps achieve a small board area. Its five power-saving modes also support periodic measurement systems that remain active only while acquiring or processing data.
Direkomendasikan
Portable Environmental Monitoring
For portable environmental monitoring, the MSP430F2272IDA combines low-power operation with enough processing capability for local sensor management. The 16 MHz CPU provides a 125 ns instruction cycle time for responsive control loops, while 512B SRAM supports working variables and 32KB Flash holds application firmware. I2C or SPI can connect digital sensors, and UART can provide a simple host or logging interface. The five power-saving modes and standby wake-up in less than 6 us allow a duty-cycled design to reduce activity while preserving quick response to scheduled measurements or external events.
Direkomendasikan
Battery-Powered Instrumentation
The MSP430F2272IDA suits battery-powered instruments where CPU activity, memory, and analog conversion must coexist in a compact controller. Its 16-bit RISC architecture and 16 MHz clock support efficient firmware execution, while the integrated 10-bit ADC handles process or instrumentation signals without a separate converter. I2C, SPI, and UART provide flexible connectivity for configuration boards, external transducers, and data loggers. Power-conscious firmware can use the device's five power-saving modes between measurements, although the final battery-life calculation must include the selected regulator, external sensor currents, and communication activity.
Direkomendasikan
Digital Communication Controller
The MSP430F2272IDA can serve as a compact communications controller in an embedded node because it provides I2C, SPI, and UART in the same device as its 16 MHz CPU. SPI suits higher-throughput peripheral links, I2C supports addressable sensors and configuration devices, and UART provides a straightforward serial console or host connection. The 32KB Flash accommodates protocol and application firmware, while 512B SRAM supports packet buffers and working state. Firmware designers should budget interrupt latency and DMA-free peripheral handling against the 125 ns instruction cycle time and validate timing with the selected bus clock.
Direkomendasikan
Embedded Motor and Actuator Control
The MSP430F2272IDA can control small actuators in cost-sensitive embedded systems because its 16 MHz RISC CPU can execute real-time control routines while the 10-bit ADC monitors command or feedback signals. GPIO resources can operate digital control logic, and I2C or SPI can connect position sensors, drivers, or H-bridge controllers. With 32KB Flash and 512B SRAM, the device is appropriate for focused control tasks rather than large application workloads. Validate timing, output switching requirements, and any safety limits in the exact peripheral implementation before using it in a motor-control design.
Direkomendasikan
Smart Home and IoT Sensor Node
The MSP430F2272IDA is appropriate for a compact IoT sensor node requiring local analog measurement and several digital interfaces. The integrated 10-bit ADC can acquire a sensor signal, while I2C or SPI connects additional sensing and identification components. UART can provide a simple gateway connection, and the 32KB Flash plus 512B SRAM supports lightweight protocol firmware. Its ultra-low-power positioning and five power-saving modes are useful for battery-operated nodes that wake for periodic sensing. For a connected product, confirm radio-module interface levels, timing, and current budget during system integration.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MSP430F2272IDA — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MSP430F2272IDAR |
|---|---|---|
| Package | 38-pin TSSOP (DA) | 38-TSSOP |
| Brand | Texas Instruments | Texas Instruments |
| Product Type | 16-bit ultra-low-power mixed-signal microcontroller | MSP430F2xx mixed-signal microcontroller |
| Maximum Clock Frequency | 16 MHz | 16 MHz |
| CPU Architecture | 16-bit RISC MSP430 | 16-bit MSP430 |
| Flash Memory | 32KB | 32KB (32K x 8 plus 256B) |
Diferensiator Kunci
- Combines a 16 MHz CPU, 10-bit ADC, and three serial interfaces in one mixed-signal MCU (vsMSP430F2272IDAR)
- 125 ns instruction cycle supports responsive embedded-control routines (vsMSP430F2272IDAR)
- Five power-saving modes suit duty-cycled sensing designs (vsMSP430F2272IDAR)
Catatan Desain
Place all required decoupling capacitors directly beside the MSP430F2272IDA power pins, with the shortest possible ground return paths. The 38-pin TSSOP footprint leaves limited pin spacing, so follow the manufacturer land pattern and keep analog, digital, and communication routes physically separated where practical. Confirm capacitor values, voltage ratings, and the recommended power topology against the Texas Instruments datasheet before fabrication.
Design the power tree around the MCU's five operating and power-saving modes. Estimate average supply current by accounting for CPU activity, ADC sampling, serial-interface traffic, and the current drawn by connected sensors rather than looking only at active-mode consumption. Firmware should disable unused peripherals and use standby wake-up, which is specified as less than 6 us, to meet a low average-current target.
Route the 10-bit ADC input away from switching supplies, high-current digital nets, and fast serial clock signals. Use a compact analog input section, maintain a continuous ground reference beneath the MCU and analog circuitry, and terminate communication routes according to the actual peripheral specifications. Because the part is in a 38-pin TSSOP package, carefully assign multiplexing pins before finalizing the schematic.
Do not assume that a related MSP430F2xx device is interchangeable solely because it has a similar clock speed or memory size. Verify the exact suffix, package, temperature range, pin multiplexing, ADC features, serial interfaces, and orderable status in the manufacturer documentation. Firmware can also require adaptation when alternate pin functions or clock settings differ, even when the PCB footprint remains the same.
Informasi Konformitas
Compliance attributes are not stated in the manufacturer and distributor records. Use the current Texas Instruments product documentation for environmental, material, and automotive qualification decisions.