MT28F800B3WG-10T - 8Mb NOR Flash, 100ns, 48-TSOP | Micron
MPN: MT28F800B3WG-10T ✗ Akhir HidupMT28F800B3WG-10T Ringkasan
NOR flash is a non-volatile memory category that retains data without power and supports random read access at byte/word granularity, sitting at the top of the boot-code/ROM hierarchy that spans mask ROM, NOR, NAND, and managed NAND. Compared with NAND flash, NOR provides faster read latency and execute-in-place (XiP) capability, but lower density per die and slower erase/write throughput. The MT28F800B3WG family operates from a single 3.3 V VCC supply (2.7 V-3.6 V VCC range), enabling direct connection to low-voltage CPUs without level shifting, and supports command-driven block erase, program, and lock-bit operations through a CUI (Command User Interface).
Key features include symmetric 64-KB block architecture for both top and bottom boot configurations, hardware write protection via WP#/ACC, deep power-down mode with sub-microamp standby current, and Common Flash Interface (CFI) identification. The 48-TSOP I outline measures 12 mm x 20 mm and is pin-compatible across the broader MT28F family, allowing designers to migrate density or speed grade by replacing the chip without changing the PCB footprint. Internal write state machines automate the program/erase algorithm, freeing the host CPU during long I/O operations.
Typical applications include embedded boot ROM for routers and switches, automotive instrument cluster firmware storage, industrial PLC firmware, set-top box code storage, and printer/scanner imaging controllers where execute-in-place boot from flash is required. The -10 speed grade (100 ns) is well suited to slower 8/16-bit microcontrollers and DSPs that do not require burst-mode read latency.
When designing with this part, ensure VCC decoupling uses 0.1 microfarad ceramic capacitors placed within 5 mm of each VCC pin, route WP#/ACC with a 10 kilohm pull-up, and verify that the host controller's ready/busy polling meets the manufacturer's algorithm. Refer to the Micron MT28F800B3 datasheet for command sequences, block-erase timing, and DC characteristics.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Alternatif penggantian untuk MT28F800B3WG-10T — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
MT28F800B3WG-9T
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MT28F800B3WG-10B
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MT28F800B3WG-10TD
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MT28F800B3WG-10T Rating Maksimal & Karakteristik Listrik
| Tipe Memori | Non-Volatile, NOR Flash |
| Ukuran Memori | 8 Mbit (524288 words x 16 / 1048576 bytes x 8) |
| Memory Organization | x16/x8 selectable |
| Access Time | 100 ns (speed grade -10) |
| Supply Voltage VCC | 2.7 V to 3.6 V (3.3 V typical) |
| Tipe Antarmuka | Parallel |
| Block Size | 64 KB symmetric blocks |
| Program/Erase Method | Command-driven via CUI |
| Write Protection | WP#/ACC hardware pin |
| Suhu Kerja | -40C to +85C (industrial) |
| Paket | 48-pin TSOP Type I |
| Tipe Mounting | Surface Mount |
| Packaging | Tape and Reel (T suffix) |
| CFI Compliance | Yes (Common Flash Interface) |
Konfigurasi Pin MT28F800B3WG-10T
| Pin produk 1 | NC — Not connected (per datasheet) |
| Pin produk 2 | BYTE# — Selects x8 (low) or x16 (high) data bus width |
| Pin produk 3 | A17 — Address input 17 |
| Pin produk 4 | A18 — Address input 18 |
| Pin produk 5 | A19 — Address input 19 |
| Pin produk 6 | A20 — Address input 20 |
| Pin produk 7 | A21 — Address input 21 |
| Pin produk 8 | WP#/ACC — Write protect / accelerated program pin |
| Pin produk 9 | RP# — Reset / power-down pin |
| Pin produk 10 | VPP — Program/erase supply (tie to VCC if unused) |
| Pin produk 11 | NC — Not connected (per datasheet) |
| Pin produk 12 | DQ15/A-1 — Data bit 15 / LSB address in x8 mode |
| Pin produk 13 | DQ7 — Data bit 7 |
| Pin produk 14 | DQ14 — Data bit 14 |
| Pin produk 15 | DQ6 — Data bit 6 |
| Pin produk 16 | DQ13 — Data bit 13 |
| Pin produk 17 | DQ5 — Data bit 5 |
| Pin produk 18 | DQ12 — Data bit 12 |
| Pin produk 19 | DQ4 — Data bit 4 |
| Pin produk 20 | DQ11 — Data bit 11 |
| Pin produk 21 | VSS — Ground |
| Pin produk 22 | DQ3 — Data bit 3 |
| Pin produk 23 | DQ10 — Data bit 10 |
| Pin produk 24 | DQ2 — Data bit 2 |
| Pin produk 25 | DQ9 — Data bit 9 |
| Pin produk 26 | DQ1 — Data bit 1 |
| Pin produk 27 | NC — Not connected (per datasheet) |
| Pin produk 28 | DQ8 — Data bit 8 |
| Pin produk 29 | DQ0 — Data bit 0 |
| Pin produk 30 | OE# — Output enable (active low) |
| Pin produk 31 | DQ14 — Data bit 14 (alternate location) |
| Pin produk 32 | VSS — Ground |
| Pin produk 33 | WE# — Write enable (active low) |
| Pin produk 34 | A0 — Address input 0 |
| Pin produk 35 | A1 — Address input 1 |
| Pin produk 36 | A2 — Address input 2 |
| Pin produk 37 | A3 — Address input 3 |
| Pin produk 38 | A4 — Address input 4 |
| Pin produk 39 | A5 — Address input 5 |
| Pin produk 40 | A6 — Address input 6 |
| Pin produk 41 | A7 — Address input 7 |
| Pin produk 42 | A8 — Address input 8 |
| Pin produk 43 | A9 — Address input 9 |
| Pin produk 44 | A10 — Address input 10 |
| Pin produk 45 | A11 — Address input 11 |
| Pin produk 46 | A12 — Address input 12 |
| Pin produk 47 | A13 — Address input 13 |
| Pin produk 48 | A14 — Address input 14 |
Aplikasi Umum
MT28F800B3WG-10T cocok untuk 6 aplikasis: Embedded Boot ROM Storage, Industrial PLC Firmware Storage, Automotive Instrument Cluster Firmware, Set-Top Box Code Storage, Printer and Scanner Imaging Controllers, Legacy Telecom Line Card Firmware.
Embedded Boot ROM Storage
The MT28F800B3WG-10T serves as boot code storage in routers, switches, and IP cameras where execute-in-place (XiP) from parallel NOR flash is required. The 8 Mbit density fits bootloader plus a small RTOS image, while the 100 ns access time allows direct CPU fetch at clock rates up to 40 MHz without wait states. The 48-TSOP I footprint is shared across the MT28F family, enabling density migration.
Direkomendasikan
Industrial PLC Firmware Storage
In industrial programmable logic controllers and HMI panels, the MT28F800B3WG-10T stores ladder-logic runtime firmware and configuration blocks, leveraging its -40C to +85C industrial temperature range per the Micron datasheet. The 64 KB symmetric block architecture allows selective updates of individual PLC program modules without disturbing the boot sector. Single 3.3 V supply simplifies power tree design alongside industrial MCUs.
Direkomendasikan
Automotive Instrument Cluster Firmware
The MT28F800B3WG-10T has historically been used in automotive instrument clusters, gauge displays, and infotainment head units requiring non-volatile storage of graphics firmware and calibration tables. Its parallel interface integrates directly with legacy automotive 16-bit microcontrollers without glue logic. The wide operating voltage range (2.7 V to 3.6 V) tolerates load-dump transients common in 12 V automotive rails.
Direkomendasikan
Set-Top Box Code Storage
Set-top box and digital TV decoder designs use the MT28F800B3WG-10T as primary boot flash for the real-time operating system and device drivers, exploiting the XIP capability to reduce DRAM footprint. The 100 ns access time aligns with typical STB MIPS/ARM core clock speeds. Hardware WP#/ACC pin supports secure firmware locking in field-deployed units.
Direkomendasikan
Printer and Scanner Imaging Controllers
Multi-function printer controllers and document scanner subsystems use the MT28F800B3WG-10T for firmware and font tables, benefiting from byte/word selectable data width and command-driven block erase for incremental font library updates. The CFI (Common Flash Interface) identification lets a single host driver support multiple flash vendors, simplifying firmware portability across product variants.
Direkomendasikan
Legacy Telecom Line Card Firmware
Telecom line cards and base-station controllers that persist through long deployment cycles rely on the MT28F800B3WG-10T for firmware storage with proven field reliability. The 8 Mbit density suits small RTOS plus boot, and the parallel interface pairs with legacy PowerPC and MIPS host CPUs. Industrial temperature range supports outdoor cabinet installations without active cooling.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MT28F800B3WG-10T — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MT28F800B3WG-9T | MT28F800B3WG-10B | MT28F800B3WG-10TD |
|---|---|---|---|---|
| Package | 48-TSOP I | 48-TSOP I - same | 48-TSOP I - same | 48-TSOP I - same |
| Brand | Micron Technology | Micron Technology - same | Micron Technology - same | Micron Technology - same |
| Density | 8 Mbit | 8 Mbit - same | 8 Mbit - same | 8 Mbit - same |
| Access Time | 100 ns | 90 ns (10% faster) | 100 ns - same | 100 ns - same |
| Supply Voltage | 2.7 V to 3.6 V | 2.7 V to 3.6 V - same | 2.7 V to 3.6 V - same | 2.7 V to 3.6 V - same |
| Operating Temperature | -40C to +85C | -40C to +85C - same | -40C to +85C - same | -40C to +105C (extended) |
| Packaging Form | Tape and Reel | Tape and Reel - same | Bulk Tray | Tape and Reel - same |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete |
Diferensiator Kunci
- Industry-standard 48-TSOP I pinout enables direct migration across MT28F family members and compatible 28F-series NOR flash from other vendors. (vsMT28F800B3WG-9T)
- Extended temperature option available within the same footprint for automotive and outdoor industrial deployments. (vsMT28F800B3WG-10TD)
- Tape-and-reel packaging supports high-volume SMT assembly without manual loading. (vsMT28F800B3WG-10B)
Catatan Desain
Decouple VCC with a 0.1 microfarad ceramic capacitor placed within 5 mm of each VCC pin, plus a bulk 10 microfarad tantalum or ceramic capacitor on the supply rail. During program and erase operations, the device draws transient current peaks; insufficient decoupling causes VCC droop that can corrupt the internal write state machine. VPP may be tied directly to VCC for in-system programming, but routing it separately allows external 12 V programming during manufacturing test.
Route address and data signals with matched trace lengths to within 50 mils to minimize skew on 16-bit parallel reads at 100 ns access time. Place the flash device as close as practical to the host CPU to reduce capacitive loading on the address bus. Provide a solid ground plane beneath the 48-TSOP footprint to shield the parallel bus from switching noise on adjacent signal layers.
Do not leave the WP#/ACC pin floating; tie it high via a 10 kilohm pull-up to VCC to prevent accidental write protection or unintended accelerated programming transitions. The RP# pin must be held high during normal operation and only pulled low for hardware reset. After power-up, the host must poll the status register before issuing program or erase commands, per the Micron command-user-interface flow.
Informasi Konformitas
RoHS, REACH, and AEC-Q100 status not explicitly stated in the Verified Web Data; compliance should be confirmed against the Micron MT28F800B3 datasheet. Part is marked obsolete by Micron.
