Texas Instruments

OPA277UA - 36V Precision Op Amp, 10uV Offset | Texas Instruments

MPN: OPA277UA ✓ Aktif
±2 V to ±18 V Vdss 8-pin SOIC Package
MOQ: 1 |

OPA277UA Ringkasan

The Texas Instruments OPA277UA is a single-channel, bipolar precision operational amplifier with 36 V maximum supply capability, 10 uV input offset voltage, and 0.1 uV/°C input offset drift, packaged in an 8-pin SOIC. It is designed for instrumentation, sensor signal conditioning, and precision analog measurement systems where low offset, low drift, high common-mode rejection, and high power-supply rejection are important.

An operational amplifier is a high-gain differential amplifier whose output responds to the voltage difference between its non-inverting and inverting inputs. Precision op amps belong to the amplifier IC category and can be divided into general-purpose, precision, and high-speed families. The OPA277UA sits in the precision family: its low offset and drift preserve measurement accuracy over time and temperature, while its high rejection ratios reduce errors caused by supply variation and signals common to both inputs.

According to the manufacturer datasheet, the OPAx277 series replaces the industry-standard OP-177 while offering improved noise, a wider output voltage swing, twice the speed, and half the quiescent current of that reference device. The series also specifies low bias current, high common-mode rejection, and high power-supply rejection. These characteristics make the amplifier useful when sensor outputs are small, when calibration accuracy must survive temperature changes, or when supply ripple could otherwise modulate the measurement.

OPA277UA operates from dual supplies of ±2 V to ±18 V, allowing it to work with ±5 V, ±12 V, and ±15 V laboratory rails. Its wide input capability supports conventional bipolar analog systems, and the 8-pin SOIC package simplifies assembly where a compact, surface-mount precision amplifier is required. The manufacturer identifies the device as a general-purpose amplifier with a single-ended output.

Typical uses include precision bridge and transducer amplifiers, laboratory instrument front ends, low-level sensor conditioning, current measurement, and high-resolution data-conversion systems. The device can also buffer slow, high-impedance sources where offset drift and bias-current error would otherwise dominate the signal chain.

When designing around the OPA277UA, verify input and output voltage limits at the selected supply voltage and keep the input common-mode range within the operating envelope. Use short, guarded signal traces and maintain stable feedback layouts because a precision amplifier preserves small signals rather than correcting poor board-level noise pickup.

This page combines manufacturer specifications, package information, drop-in replacement analysis, comparison parameters, and practical design guidance for engineers evaluating the OPA277UA.

Alternatif penggantian untuk OPA277UA — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian OPA277UA (sama faktor bentuk dan footprint) — berbeda di dalam Amplifier Type, Package, Supply Voltage Range, Slew Rate, Operating Temperature Range.

Analog Devices
Amplifier Type: J-FET
Bandingkan dengan OPA277UA →
STMicroelectronics
Amplifier Type: Standard general-purpose operational amplifier
Package: 8-TSSOP
Bandingkan dengan OPA277UA →
Texas Instruments
Amplifier Type: Precision Operational Amplifier
Package: 8-SOIC (D), 3.90 mm body width
Supply Voltage Range: +/-3 V to +/-18 V dual, 6 V to 36 V single
Bandingkan dengan OPA277UA →
Texas Instruments
Amplifier Type: Precision Operational Amplifier
Package: 8-SOIC (D), 3.90 mm body width
Supply Voltage Range: +/-3 V to +/-18 V dual, 6 V to 36 V single
Bandingkan dengan OPA277UA →
Texas Instruments
Supply Voltage Range: ±5 V to ±18 V
Slew Rate: 2.5 V/µs
Bandingkan dengan OPA277UA →
Texas Instruments
Amplifier Type: Single, General Purpose, FET-Input Operational Amplifier
Package: 8-pin SOIC (D), surface mount
Supply Voltage Range: +/-2.25 V to +/-18 V
Bandingkan dengan OPA277UA →
Texas Instruments
Amplifier Type: Precision Operational Amplifier
Package: 8-pin SOIC (D)
Slew Rate: 2 V/µs
Bandingkan dengan OPA277UA →
Texas Instruments
Amplifier Type: Precision, Low Noise
Package: SOIC-8 (D)
Slew Rate: 2.3 V/us
Bandingkan dengan OPA277UA →
Texas Instruments
Amplifier Type: Single precision operational amplifier
Package: 8-pin PDIP (P), 0.300 inch (7.62 mm) pitch
Supply Voltage Range: 2 V to 18 V
Bandingkan dengan OPA277UA →
Texas Instruments
Amplifier Type: Precision bipolar operational amplifier
Slew Rate: 0.8 V/µs
Bandingkan dengan OPA277UA →
Texas Instruments
Operating Temperature Range: -40°C to +85°C
Bandingkan dengan OPA277UA →

OPA277U

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
Texas Instruments
📦 8-pin SOIC
Precision bipolar operational amplifier · 1 circuit · 36 V · ±2 V to ±18 V · 10 µV · 0.1 µV/°C · 1 MHz · 0.8 V/µs

Kontak untuk harga

Lihat Datasheet →

OPA277UG4

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 8-pin SOIC
Same OPA277 precision family and 8-pin SOIC footprint; verify temperature grade, lead finish, and order code

📋 Alternatif referensi (tidak dalam katalog)

OPA27GU

✅ Drop-In
Texas Instruments
📦 8-pin SOIC
Ultra-low-noise precision operational amplifier · 4.5 nV/√Hz maximum at 1 kHz · 100 µV maximum · 0.4 µV/°C maximum · 117 dB minimum · 100 dB minimum · 94 dB minimum · 8 MHz

Kontak untuk harga

Lihat Datasheet →

OPA2277UA

✅ Drop-In
Texas Instruments
📦 8-pin SOIC
2 (Dual) · Precision Operational Amplifier · 10 µV · ±0.1 µV/°C · 134 dB · 140 dB · 130 dB · 800 µA

Kontak untuk harga

Lihat Datasheet →

AD8627ARZ

✅ Drop-In
Analog Devices
📦 8-pin SOIC
J-FET · 1 · Rail-to-Rail · 900 µA (max)

Kontak untuk harga

Lihat Datasheet →

OPA277UA Rating Maksimal & Karakteristik Listrik

Amplifier Type Single-channel precision operational amplifier
Topologi Single-ended output
Architecture Bipolar
Supply Voltage Range ±2 V to ±18 V
Maximum Supply Voltage 36 V
Input Offset Voltage 10 uV maximum
Input Offset Voltage Drift 0.1 uV/°C maximum
Noise Performance Improved relative to the OP-177 reference device
Paket 8-pin SOIC
Tipe Mounting Surface mount

Konfigurasi Pin OPA277UA

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin produk 1 NC — Not connected
Pin produk 2 -IN — Inverting input
Pin produk 3 +IN — Non-inverting input
Pin produk 4 V- — Negative supply connection
Pin produk 5 NC — Not connected
Pin produk 6 OUT — Analog output
Pin produk 7 V+ — Positive supply connection
Pin produk 8 NC — Not connected

Aplikasi Umum

OPA277UA cocok untuk 6 aplikasis: Precision Bridge and Transducer Amplification, Laboratory Instrument Front End, High-Resolution Data Acquisition, Precision Current Measurement, Low-Level Sensor Buffering, Precision Audio and Reference Signal Paths.

🏭

Precision Bridge and Transducer Amplification

The OPA277UA fits low-level bridge measurements because its 10 uV maximum input offset voltage and 0.1 uV/°C maximum offset drift reduce errors that would otherwise be amplified by high gain. Place the amplifier where the bridge return path is short and shielded so that thermal gradients and leakage currents do not add more error than the device itself. Its high common-mode rejection and high power-supply rejection also help when the sensor is powered from a rail that carries switching ripple. Resistor-network matching remains important because amplifier specifications alone cannot correct imbalance in the bridge or feedback network.

🖥️

Laboratory Instrument Front End

Use the OPA277UA when a laboratory or test instrument must amplify a small differential signal without adding significant offset drift. Its 36 V maximum supply capability supports ±15 V analog rails, while the ±2 V to ±18 V operating range also permits lower-voltage laboratory systems. The precision architecture is valuable in buffer, difference, and feedback configurations where calibration stability affects traceability. Keep high-impedance input traces short, guard the inverting input when leakage is significant, and follow the manufacturer guidance for compensation and output-load stability.

📡

High-Resolution Data Acquisition

The OPA277UA is suitable for conditioning a sensor signal ahead of a high-resolution converter when offset and temperature drift dominate the measurement error. Its 10 uV maximum offset and 0.1 uV/°C maximum drift preserve millivolt-level information more effectively than a general-purpose amplifier, while high common-mode rejection limits disturbance from signals common to both inputs. Place the amplifier close to the converter input to minimize pickup between the analog output and the sampling circuit, and verify that the selected converter input range is compatible with the amplifier output swing.

⚡

Precision Current Measurement

The OPA277UA can amplify the output of a shunt or current transducer where the measured signal is small and accuracy must be retained over temperature. Its 10 uV maximum offset and 0.1 uV/°C maximum drift limit amplifier-generated errors, and its high power-supply rejection helps isolate the measurement from supply variations. A dedicated current-sense amplifier may integrate the shunt amplifier and reference more efficiently, so use the OPA277UA when flexibility, bipolar signal handling, or standalone precision amplification is more important than integration.

🧩

Low-Level Sensor Buffering

The OPA277UA works well as a buffer for high-impedance sensors where bias current, offset, and drift can dominate the available signal. Low bias current is specifically identified among the OPAx277 family characteristics, while the 10 uV maximum offset supports accurate output scaling into a downstream converter or measurement block. Keep the input node physically small, avoid long unshielded traces, and prevent conductive contamination on the board because surface leakage can exceed the amplifier's input current and destroy the benefit of a high-impedance design.

🎧

Precision Audio and Reference Signal Paths

The OPA277UA can serve as a low-level audio buffer or reference-signal amplifier when channel matching, offset stability, and low-level noise are more important than wideband audio bandwidth. The manufacturer describes the OPAx277 family as offering improved noise relative to the OP-177 reference device, while the 10 uV maximum offset and 0.1 uV/°C maximum drift help maintain channel-to-channel consistency. Confirm the amplifier's gain-bandwidth and output-drive requirements for the selected audio path, and place it where the return currents from digital and power-conversion circuitry cannot enter the signal ground.

What are the key specifications of OPA277UA that engineers should know?
The OPA277UA is a single-channel bipolar precision operational amplifier with a 36 V maximum supply rating, 10 uV input offset voltage, and 0.1 uV/°C offset drift in an 8-pin SOIC package. According to the Texas Instruments OPA277 datasheet, the OPAx277 series also provides improved noise, wider output voltage swing, low bias current, high common-mode rejection, and high power-supply rejection relative to the OP-177 reference device.
What is the supply voltage range of the OPA277UA?
The OPA277UA operates from ±2 V to ±18 V, corresponding to a total supply span of 4 V to 36 V. Texas Instruments identifies the OPA277 family as a dual, 36 V precision amplifier, and the OPA277UA package option contains one amplifier circuit. This range supports common ±5 V, ±12 V, and ±15 V analog rails while allowing operation below those nominal rail levels when the circuit and output loading permit.
Where can I download the OPA277UA datasheet PDF?
The official OPA277UA datasheet PDF is available from the Texas Instruments literature link for the OPAx277 family. It contains the electrical characteristics, pin configuration, typical performance curves, and application information needed for design review. The manufacturer product page for the OPA277UA also provides ordering information and links to the same family documentation.
Where can I find the OPA277UA pinout?
The OPA277UA pin configuration is shown in the pinout section of the manufacturer datasheet and on the official product page. The device is an 8-pin SOIC single-amplifier package with supply, input, output, and no-connect positions. Use the manufacturer pin-description table when assigning PCB tracks and confirm orientation against the package marking and silkscreen before fabrication.
Is OPA277UA suitable for precision instrumentation?
Yes, the OPA277UA is well suited to precision instrumentation because it combines a 10 uV maximum input offset voltage with 0.1 uV/°C maximum offset drift. Those characteristics reduce errors in bridge, transducer, and sensor-amplifier circuits. The manufacturer also specifies high common-mode rejection and high power-supply rejection, which helps suppress errors from supply noise and signals appearing equally on both inputs.
What can replace the OPA277UA without changing the PCB?
Several precision amplifiers in the 8-pin SOIC format can serve as drop-in candidates, but each substitution must be checked for offset, drift, supply range, bias current, stability, and output-swing requirements. OPA277U and OPA277UG4 are closely related Texas Instruments options. OPA27GU, OPA2277UA, and AD8627ARZ are cross-reference candidates whose precision performance should be compared against the OPA277UA on the actual supply rail.
What is the difference between OPA277UA and OPA277U?
OPA277UA and OPA277U belong to the same Texas Instruments OPA277 precision-amplifier family and are ordered with an 8-pin SOIC footprint. Their ordering codes differ, and the manufacturer discusses pack-size and lead-finish distinctions between available OPA277UA order codes. Verify the specific orderable part, temperature grade, reel configuration, and lead finish in the manufacturer part-details table before treating the two as production equivalents.
What is the difference between OPA277UA and OPA27GU?
OPA277UA and OPA27GU are both Texas Instruments precision amplifiers associated with an 8-pin SOIC footprint, but they belong to different series. The OPA277 series is specified as a modern replacement for the OP-177 and emphasizes improved noise, wider output swing, higher speed, and lower quiescent current. The OPA27GU may differ in offset, drift, bias current, bandwidth, and supply-current behavior, so those ratings should be compared before substitution.
Is OPA277UA the same as OPA2277UA?
No, the OPA277UA and OPA2277UA are different manufacturers' precision amplifiers, although both can be considered in an 8-pin SOIC substitution review. Their key offset, drift, noise, bias-current, bandwidth, supply-current, and output-swing ratings can differ materially. Use OPA2277UA as a cross-reference candidate rather than a guaranteed equivalent, and verify the complete operating envelope in the manufacturer datasheet.
What is the best Analog Devices equivalent for OPA277UA?
The OPA2277UA is a relevant Analog Devices candidate for an 8-pin SOIC precision-amplifier substitution because it is included in precision-amplifier cross-reference listings. It is not an automatic functional match: offset voltage, offset drift, bias current, common-mode range, output swing, and noise must satisfy the target design. Confirm the exact candidate and its ratings against the OPA277UA before releasing a production substitution.
When should I choose OPA277UA instead of OPA27GU?
Choose the OPA277UA when the design needs the newer OPAx277 performance profile, including the manufacturer-described improvements in noise and output swing, together with lower quiescent current than the OP-177 reference device. Choose OPA27GU only after confirming that its offset, drift, bias current, bandwidth, and supply-current ratings meet the same accuracy and power targets in an 8-pin SOIC layout.
Is OPA277UA suitable for bridge and sensor signal conditioning?
Yes, the OPA277UA is appropriate for low-level bridge and sensor-conditioning circuits because its 10 uV maximum offset and 0.1 uV/°C maximum drift help preserve accuracy across temperature. High common-mode rejection and high power-supply rejection are also valuable when the sensor output is small and the amplifier is powered from a rail that may carry ripple. Resistor matching and careful common-mode-range checks remain essential.
How much power does the OPA277UA dissipate?
The OPA277UA dissipation depends on the selected supply voltages, quiescent current, output load, and ambient temperature. The manufacturer datasheet provides the complete maximum-current and thermal ratings, including the operating-temperature range. Calculate total device power from the supply current and rail voltage, then compare the resulting junction temperature with the package and ambient limits before allowing full output load.
Where can I buy OPA277UA online?
The OPA277UA can be ordered through authorized distribution channels, and the official manufacturer part-details page lists commercial ordering options. For a current quote, package configuration, and confirmed availability, use the Request a Quote form on this page. Provide the exact OPA277UA order code, target quantity, reel or tray preference, and required delivery date.
What is the lead time for OPA277UA?
Lead time depends on current inventory, the selected package and reel option, order volume, and factory loading at the time of purchase. Request the current lead time and minimum order quantity through the Request a Quote form on this page. Supply a forecast and target production date so procurement can confirm allocation rather than relying on a static availability statement.
Is the OPA277UA currently in stock?
Stock levels for the OPA277UA change with order configuration and regional demand, so availability must be confirmed for the exact suffix and reel quantity. Use the Request a Quote form on this page to request current stock, scheduled delivery, and minimum order quantity. The exact manufacturer ordering information for OPA277UA is also available on the official Texas Instruments part-details page.

Data referensi engineering untuk OPA277UA — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the OPA277UA when your design needs a single precision amplifier with 10 uV maximum offset, 0.1 uV/°C maximum drift, a 36 V maximum supply rating, and high common-mode and power-supply rejection. Prefer OPA277U or OPA277UG4 for the closest same-family continuity, after confirming order code, temperature grade, lead finish, and reel configuration. Consider OPA27GU when its lower-cost legacy series still meets the required offset, drift, bandwidth, bias-current, and supply-current limits. OPA2277UA and AD8627ARZ are reasonable cross-brand candidates when sourcing continuity requires a second manufacturer, but they should be treated as engineering substitutions rather than automatic equivalents. Validate stability, common-mode range, output swing, noise, bias current, and calibration performance on the actual supply rails before approving any change.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini OPA277U OPA277UG4 OPA27GU OPA2277UA AD8627ARZ
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Analog Devices Analog Devices
Package 8-pin SOIC 8-pin SOIC - same footprint 8-pin SOIC - same footprint 8-pin SOIC - same footprint 8-pin SOIC - same footprint 8-pin SOIC - same footprint
Amplifier Configuration Single amplifier Single amplifier Single amplifier Single amplifier Single amplifier Single amplifier

Diferensiator Kunci

  • Low offset and drift for precision measurement (vsOPA27GU)
  • Modern family performance relative to the OP-177 reference (vsOPA27GU)
  • Broad bipolar supply operating range (vsOPA2277UA)
  • Same-brand ordering continuity (vsOPA2277UA)

Catatan Desain

Do not treat the 36 V maximum supply rating as permission to operate at 36 V under every load and temperature condition. Design around the ±2 V to ±18 V family range, confirm the selected amplifier's input common-mode limits, and verify output swing at the actual load. The 10 uV offset specification applies within its stated test conditions; resistor imbalance, input bias current, thermoelectric effects, and PCB leakage can still dominate a millivolt-level measurement.

Route the non-inverting and inverting inputs as short, symmetric, guarded traces, and keep the feedback loop compact. For high-impedance sensors, use a driven guard or physical shield around the input node to control leakage and surface contamination. Connect the analog return path so output-current noise and switching-node currents do not flow through the measurement reference. These layout practices protect the low-offset performance more effectively than additional gain.

Place local bypass capacitance from each supply pin to the appropriate analog ground node, using the capacitance and placement recommended in the manufacturer datasheet. Decouple the OPA277UA close to the device so switching supply noise is attenuated before it reaches the amplifier. Because the OPAx277 series provides high power-supply rejection, good supply decoupling remains the practical way to realize that rejection in a real board rather than treating the datasheet ratio as a substitute for layout.

Check stability with the intended gain, source impedance, output load, and any capacitive input or output loading before the PCB is released. Precision op amps can require noise-gain compensation in non-inverting or difference-amplifier topologies. Simulate the complete feedback network with the actual sensor impedance and cable capacitance, and confirm that the selected replacement part also remains stable under those same conditions.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

Compliance status was not explicitly stated for the OPA277UA and must be confirmed from the current manufacturer product documentation before release to environmentally constrained or automotive programs.

Pencarian Terkait

opa277ua datasheet OPA277UA datasheet PDF OPA277UA pinout OPA277UA specifications OPA277UA SOIC-8 OPA277UA precision op amp Texas Instruments OPA277UA OPA277UA drop-in replacement OPA277UA vs OPA27GU OPA277UA equivalent OPA277UA price OPA277UA stock OPA277UA bridge amplifier OPA277UA instrumentation application

Komponen dan Istilah Terkait

Texas Instruments OPA277UA OPA277 OPA277U OPA277UG4 OPA27GU OPA2277UA AD8627ARZ precision operational amplifier amplifier IC bipolar operational amplifier input offset voltage input offset drift common-mode rejection ratio power supply rejection ratio input bias current SOIC-8 surface-mount package precision instrumentation bridge amplifier sensor signal conditioning 36 V supply rating RoHS REACH
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ