Texas Instruments

OPA642PB - Wideband Low-Distortion Op Amp | Texas Instruments

MPN: OPA642PB ✓ Aktif
±4.5 V to ±5.5 V Vdss 25 uA Id 8-pin PDIP, 0.300 inch (7.62 mm) pitch Package
MOQ: 1 |

OPA642PB Ringkasan

Texas Instruments OPA642PB is a single wideband, low-distortion, low-gain operational amplifier with a supply voltage range of ±4.5 V to ±5.5 V. The device is specified as a 90 dB instrumentation amplifier-class part with 25 uA and 70 uA operating-current figures, and it is packaged in an 8-pin PDIP package. Its primary role is to amplify low-amplitude signals while maintaining bandwidth and low distortion across wide operating frequencies.

An operational amplifier is a voltage-feedback differential amplifier that uses negative feedback to control gain and linearity. The OPA642PB belongs to the instrumentation operational-amplifier family and sits within the broader voltage-feedback amplifier, analog signal-chain, and semiconductor hierarchies. Instrumentation-oriented amplifiers are commonly used where signal gain, low distortion, and accurate differential input handling are more important than minimum cost or the lowest possible quiescent current.

The OPA642PB emphasizes wideband signal amplification and low distortion. Its stated 90 dB specification is associated with the device’s instrumentation-amplifier positioning, while the 25 uA and 70 uA figures identify the operating-current characteristics highlighted by the product listings. Operation from ±4.5 V to ±5.5 V suits dual-supply analog systems that require symmetric biasing around ground. The 8-pin PDIP package also supports conventional through-hole assembly and prototyping rather than compact surface-mount production.

OPA642PB is suitable for precision signal conditioning, data-acquisition front ends, instrumentation chains, and low-level sensor amplification. The wideband architecture makes it appropriate when signal bandwidth must be preserved, while the low-gain and low-distortion positioning helps reduce signal degradation in higher-gain stages. Designers should still account for input and output settling, gain-bandwidth behavior, output swing, input common-mode range, and noise when establishing the complete amplifier circuit.

Typical uses include sensor-interface amplification, receiver signal conditioning, laboratory instrumentation, and communications signal chains. In these systems, OPA642PB can amplify a differential sensor output before conversion or further processing. The choice of feedback network remains important: resistor values determine closed-loop gain, while parasitic capacitance and board layout can affect stability and achievable bandwidth.

For PCB implementation, keep feedback components close to the amplifier pins and provide low-impedance supply bypass paths near the power terminals. Check the absolute maximum ratings, recommended operating conditions, common-mode limits, and output-swing limits in the manufacturer datasheet before applying the device to a new voltage or gain configuration. Decoupling, grounding, and clean reference returns are especially important when small signals are amplified close to the circuit’s noise floor.

This page combines the exact catalog attributes, package information, sourcing structure, and carefully qualified drop-in alternatives for OPA642PB. It also adds selection guidance and practical implementation notes intended to help engineers distinguish a true pin-compatible replacement from a merely similar amplifier.

Alternatif penggantian untuk OPA642PB — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian OPA642PB (sama faktor bentuk dan footprint) — berbeda di dalam Package, Product Type, Common-Mode Rejection Ratio.

Texas Instruments
Package: 8-pin PDIP
Product Type: Voltage-feedback operational amplifier
Common-Mode Rejection Ratio: 85 dB
Bandingkan dengan OPA642PB →
Texas Instruments
Package: 8-pin PDIP
Common-Mode Rejection Ratio: 90 dB
Bandingkan dengan OPA642PB →

OPA642P

✅ Drop-In
Texas Instruments
📦 8-pin PDIP
Wideband, low-distortion, low-gain operational amplifier · Single voltage-feedback amplifier · 1 circuit · 400 MHz · ±5.5 V · 95 dB · 90 dB · 2.7 nV/√Hz

Kontak untuk harga

Lihat Datasheet →

OPA641P

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 8-pin PDIP
Same 8-pin PDIP single-amplifier package; detailed bandwidth and offset differences versus OPA642PB are unquantified in the available information, supporting an estimated 80% key-parameter proximity.

📋 Alternatif referensi (tidak dalam katalog)

OPA640P

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
Texas Instruments
📦 8-pin PDIP
Voltage-feedback operational amplifier · 1 circuit · 1.3 GHz · Unity-gain stable · 2.9 nV/√Hz · 85 dB · 350 V/µs · 10 MHz

Kontak untuk harga

Lihat Datasheet →

OPA642PB Rating Maksimal & Karakteristik Listrik

Product Type Wideband, low-distortion, low-gain operational amplifier
Amplifier Architecture Single voltage-feedback operational amplifier
Supply Voltage Range ±4.5 V to ±5.5 V
Single Supply Equivalent Range 9 V to 11 V
Stated Gain Figure 90 dB
Operating Current 25 uA
Arus Memerintah 70 uA
Number of Circuits 1 circuit
Jumlah Pin 8 pins
Paket 8-pin PDIP, 0.300 inch (7.62 mm) pitch
Terminal Type Through-hole
Package Shape Rectangular
Temperature Grade Industrial

OPA642PB rectangular Diamant Konfigurasi Panduan

Konfigurasi pin untuk OPA642PB (rectangular pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.

Diamant diagram pakai pakai rectangular untuk OPA642PB

Tidak ada data diatribut pin yang tersedia untuk OPA642PB.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

OPA642PB cocok untuk 6 aplikasis: Precision Sensor Signal Conditioning, Communications Receiver Front End, Laboratory Instrumentation, Data Acquisition Front End, Audio and Low-Level Analog Amplification, Industrial Control and Measurement.

🧩

Precision Sensor Signal Conditioning

OPA642PB fits low-level sensor front ends that require a wideband amplifier rather than a slow precision-only amplifier. Its single voltage-feedback topology supports straightforward inverting and noninverting configurations, while the ±4.5 V to ±5.5 V operating range accommodates symmetric analog rails around ground. Place the feedback network close to the amplifier and verify the sensor output remains inside the input common-mode range. The low-distortion and low-gain positioning can help preserve small signals before ADC conversion.

🌐

Communications Receiver Front End

OPA642PB can amplify receiver signals when the selected gain must preserve bandwidth and limit distortion. Its wideband, low-gain operational-amplifier characterization makes it more relevant than a general-purpose slow amplifier for intermediate-frequency or broadband signal paths. The ±4.5 V to ±5.5 V supply operation supports centered dual-rail analog systems. Validate gain-bandwidth product, slew rate, common-mode range, and output swing against the highest operating frequency before deployment.

🔧

Laboratory Instrumentation

OPA642PB is appropriate for laboratory instrumentation where a compact through-hole amplifier can be placed close to sensitive analog circuitry. The 8-pin PDIP package simplifies breadboard and legacy instrument-board assembly, while the wideband low-distortion design supports signal conditioning beyond very slow measurement rates. Use short feedback traces, a solid ground reference, and local supply bypassing. Confirm the exact pinout and suffix-specific temperature limits before finalizing the instrument board.

🖥️

Data Acquisition Front End

OPA642PB can serve as the gain stage ahead of a data-acquisition converter when low distortion and bandwidth are priorities. Its single-circuit architecture avoids sharing an internal amplifier package with unrelated functions, and the ±4.5 V to ±5.5 V range suits bipolar sensor interfaces. Select the feedback ratio so signal gain remains compatible with the amplifier’s bandwidth and output swing. Route the conditioned output directly toward the converter to minimize added noise and pickup.

🎧

Audio and Low-Level Analog Amplification

OPA642PB can amplify low-level audio or control signals when the design values low distortion over the required signal bandwidth. Its instrumentation-style low-gain architecture supports analog preamplification without relying on a high closed-loop gain that could reduce bandwidth or compromise stability. The symmetric supply requirement should be checked against the source and load. Decouple each supply rail near the device and compare the calculated output swing with the signal peak before selecting the feedback network.

🏭

Industrial Control and Measurement

OPA642PB can condition low-voltage signals in industrial measurement modules when the system uses symmetric analog rails and requires predictable wideband behavior. The through-hole PDIP package supports panel boards and modular industrial control assemblies. Keep sensitive inputs away from switching nodes and provide a low-impedance return path to the amplifier ground. Because industrial environments can introduce temperature and supply variation, confirm the exact OPA642PB temperature grade, supply tolerances, and output capability in the manufacturer datasheet.

What is OPA642PB?
OPA642PB is a Texas Instruments single wideband, low-distortion, low-gain operational amplifier intended for instrumentation and precision signal-conditioning circuits. The device operates from ±4.5 V to ±5.5 V and is offered in an 8-pin PDIP package. Texas Instruments describes the device as a wideband, low-distortion, low-gain operational amplifier, positioning it for applications where signal fidelity is more important than minimum cost.
What are the key specifications of OPA642PB that engineers should know?
OPA642PB is a single-circuit, voltage-feedback operational amplifier with a ±4.5 V to ±5.5 V supply range, an 8-pin PDIP package, a stated 90 dB gain figure, and highlighted operating-current values of 25 uA and 70 uA. According to the Texas Instruments datasheet for OPA642PB, its defining characteristics are wideband operation, low distortion, and low-gain amplification. The package uses a 0.300-inch, 7.62 mm pitch.
What supply voltage does OPA642PB require?
OPA642PB requires a nominal dual supply of ±4.5 V to ±5.5 V for the operating range identified in its product documentation. This corresponds to a total supply span of 9 V to 11 V when both rails are referenced to ground. The device is therefore suitable for centered bipolar analog rails rather than a direct single-supply arrangement without appropriate biasing.
What package does OPA642PB use?
OPA642PB uses an 8-pin PDIP package with a 0.300-inch, 7.62 mm lead pitch. Its terminals are arranged for through-hole PCB assembly, and the package is rectangular. This package choice makes OPA642PB convenient for prototypes, laboratory boards, and legacy-style through-hole production where a surface-mount operational amplifier would be less convenient.
Where can I download the OPA642PB datasheet PDF?
The OPA642PB manufacturer datasheet can be located through the Texas Instruments product documentation or through the indexed datasheet result linked on this page. The indexed document is a 176 KB, 16-page PDF containing the device description and electrical information. Use the Texas Instruments datasheet as the controlling document for pin functions, absolute maximum ratings, recommended operating conditions, and test conditions.
Where can I find the OPA642PB pinout?
The OPA642PB pin functions are identified in the pin-configuration section of the Texas Instruments manufacturer datasheet. The component is an 8-pin PDIP device, so the package diagram should be cross-checked against the exact OPA642PB ordering code before PCB routing. Use the manufacturer pin-description table when assigning input, output, supply, offset-null, and no-connect terminals.
Is OPA642PB suitable for instrumentation applications?
OPA642PB is suitable for instrumentation applications because it is expressly categorized as a wideband, low-distortion, low-gain operational amplifier with a stated 90 dB gain figure. It can serve as the active element in low-level sensor and receiver signal paths when its input common-mode range, output swing, noise, and stability behavior satisfy the circuit requirements. Verify those limits in the manufacturer datasheet.
OPA642PB vs OPA642P — which part should I use?
OPA642PB and OPA642P are both listed as 8-pin PDIP operational amplifiers, but the ordering-code suffix may identify different qualification, grade, or packaging conditions. The available product information confirms the through-hole package for both parts but does not expose every suffix-specific rating. Confirm temperature grade, markings, and lead-processing requirements against the manufacturer datasheet before treating OPA642P as an interchangeable substitute.
When should I choose OPA642PB over a lower-speed general-purpose amplifier?
Choose OPA642PB when the signal path requires the amplifier’s wideband, low-distortion positioning and the operating point is compatible with ±4.5 V to ±5.5 V supplies. A lower-speed general-purpose amplifier may be sufficient for slow sensor signals but can introduce bandwidth or distortion limitations as frequency and closed-loop gain increase. Confirm gain-bandwidth product, slew rate, output swing, and stability before final selection.
What is the best drop-in replacement for OPA642PB?
OPA642P is the closest listed through-hole option because it is also identified as an 8-pin PDIP single-circuit operational amplifier. OPA641P and OPA640P are additional same-family candidates that merit pin and specification review, but the available cross-reference information does not establish every electrical parameter as identical. Treat OPA642P as the leading replacement candidate and validate offset, bandwidth, slew rate, common-mode range, and output swing.
Can OPA642P replace OPA642PB without changing the PCB?
OPA642P can fit the same physical 8-pin PDIP footprint, but physical fit alone does not guarantee electrical drop-in compatibility. The two listings identify the same general device family and package, while detailed suffix-specific limits remain unconfirmed. Verify the manufacturer pin configuration, supply range, temperature grade, input characteristics, output swing, and any offset-null function before approving OPA642P for production.
What can replace OPA642PB?
OPA642P is the most direct replacement candidate because both parts are listed as single-circuit operational amplifiers in an 8-pin PDIP package. OPA641P and OPA640P may also be considered within the same manufacturer family, but their exact pin compatibility and parameter differences require comparison with the OPA642PB datasheet. No cross-brand drop-in replacement is established by the available cross-reference information.
Is OPA642PB the same as OPA642P?
OPA642PB and OPA642P are closely related 8-pin PDIP single operational amplifiers, but they are not confirmed as identical in every suffix-specific characteristic. The available listings confirm the common package and circuit count. A production substitution should still be checked against temperature range, offset voltage, bias current, bandwidth, slew rate, output swing, pin function, and lifecycle status.
Where can I buy OPA642PB and what is its lead time?
OPA642PB can be requested through the Request a Quote form on this page, where current commercial availability and lead time should be confirmed for the exact 8-pin PDIP ordering code. The device is a standard catalog part with an 8-pin PDIP package, but no qualifying current quantity-break listing is shown here. Packaging quantities and delivery timing should therefore be confirmed with the quotation.
What is the price of OPA642PB?
The current commercial price of OPA642PB should be obtained through the Request a Quote form on this page. No current listing with explicit quantity-break prices for the exact OPA642PB ordering code is available for structured extraction, so a static price is not presented. The quote request should include the required quantity, tube packaging preference, and destination to establish current delivery terms.
Is OPA642PB in stock?
OPA642PB stock status should be confirmed through the Request a Quote form on this page for the exact OPA642PB ordering code. One indexed result reports in-stock status, but no current structured stock quantity is established for this product record. The quotation response should confirm available inventory, factory or distributor lead time, and the permitted tube quantity for your order.

Data referensi engineering untuk OPA642PB — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose OPA642PB when the design calls for a single wideband, low-distortion, low-gain operational amplifier operated from ±4.5 V to ±5.5 V rails. OPA642P is the closest listed replacement candidate because it retains the single-circuit, 8-pin PDIP architecture, but it should be selected only after checking suffix-specific electrical and temperature ratings. Consider OPA641P when its measured bandwidth, noise, offset, and slew-rate behavior better matches the intended gain; its detailed differences are not established in the available comparison information. OPA640P is a further same-family option, but the manufacturer datasheets must be compared before treating it as a drop-in replacement. No cross-brand candidate is established as both pin-compatible and parametrically equivalent, so it is not recommended without a PCB-level and performance qualification program.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini OPA642P OPA641P OPA640P
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Product Family OPA642 wideband low-distortion operational amplifier OPA642 family OPA641 family OPA640 family
Circuit Count 1 circuit 1 circuit 1 circuit 1 circuit

Diferensiator Kunci

  • Established wideband low-distortion device positioning (vsOPA641P)
  • Documented operating range and current characteristics (vsOPA640P)
  • Exact package and single-circuit architecture (vsOPA642P)

Catatan Desain

Place OPA642PB close to the protected signal source and keep both feedback resistors adjacent to the relevant input and output pins. Longer loops around the amplifier can pick up noise and add parasitic capacitance that changes stability or bandwidth. Route the non-inverting input away from supply, clock, and digital return paths, and use a continuous ground reference rather than splitting analog and power grounds under the device.

Decouple each OPA642PB supply rail close to its package connection, and keep the return current associated with bypass capacitors separate from sensitive input returns. The supported operating range is ±4.5 V to ±5.5 V, so verify startup, rail sequencing, and maximum supply conditions in the manufacturer datasheet. If the source signal is referenced to ground, confirm the output can reach the required peak swing before increasing the closed-loop gain.

Do not treat matching the 8-pin PDIP footprint as proof of complete replacement compatibility. Confirm the exact pin functions, offset-null behavior, input common-mode range, output swing, gain-bandwidth product, slew rate, and suffix-specific temperature rating for OPA642P, OPA641P, or OPA640P. After substitution, repeat AC and DC testing across the intended load range because small differences in offset, bias current, or compensation can alter low-level signal accuracy.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for this ordering code. AEC-Q100 qualification is treated as not applicable because OPA642PB is listed as an industrial-grade operational amplifier rather than an automotive-qualified device.

Data disahkan pada: 2026-11-19 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

OPA642PB datasheet OPA642PB pinout OPA642PB datasheet pdf OPA642PB specifications OPA642PB 8-DIP Texas Instruments OPA642PB OPA642PB replacement OPA642PB equivalent OPA642PB vs OPA642P OPA642PB price OPA642PB stock OPA642PB instrumentation amplifier OPA642PB signal conditioning OPA642PB through-hole op amp

Komponen dan Istilah Terkait

Texas Instruments OPA642PB OPA642P OPA641P OPA640P operational amplifier voltage-feedback amplifier instrumentation amplifier single amplifier analog signal chain semiconductor PDIP-8 DIP package family through-hole surface-mount through-hole package hierarchy wideband amplifier low-distortion amplifier low-gain amplifier gain bandwidth product slew rate input common-mode range output voltage swing input offset voltage dual supply signal conditioning
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ