OPA642PB - Wideband Low-Distortion Op Amp | Texas Instruments
N.º da peça: OPA642PB ✓ AtivoOPA642PB Visão geral
An operational amplifier is a voltage-feedback differential amplifier that uses negative feedback to control gain and linearity. The OPA642PB belongs to the instrumentation operational-amplifier family and sits within the broader voltage-feedback amplifier, analog signal-chain, and semiconductor hierarchies. Instrumentation-oriented amplifiers are commonly used where signal gain, low distortion, and accurate differential input handling are more important than minimum cost or the lowest possible quiescent current.
The OPA642PB emphasizes wideband signal amplification and low distortion. Its stated 90 dB specification is associated with the device’s instrumentation-amplifier positioning, while the 25 uA and 70 uA figures identify the operating-current characteristics highlighted by the product listings. Operation from ±4.5 V to ±5.5 V suits dual-supply analog systems that require symmetric biasing around ground. The 8-pin PDIP package also supports conventional through-hole assembly and prototyping rather than compact surface-mount production.
OPA642PB is suitable for precision signal conditioning, data-acquisition front ends, instrumentation chains, and low-level sensor amplification. The wideband architecture makes it appropriate when signal bandwidth must be preserved, while the low-gain and low-distortion positioning helps reduce signal degradation in higher-gain stages. Designers should still account for input and output settling, gain-bandwidth behavior, output swing, input common-mode range, and noise when establishing the complete amplifier circuit.
Typical uses include sensor-interface amplification, receiver signal conditioning, laboratory instrumentation, and communications signal chains. In these systems, OPA642PB can amplify a differential sensor output before conversion or further processing. The choice of feedback network remains important: resistor values determine closed-loop gain, while parasitic capacitance and board layout can affect stability and achievable bandwidth.
For PCB implementation, keep feedback components close to the amplifier pins and provide low-impedance supply bypass paths near the power terminals. Check the absolute maximum ratings, recommended operating conditions, common-mode limits, and output-swing limits in the manufacturer datasheet before applying the device to a new voltage or gain configuration. Decoupling, grounding, and clean reference returns are especially important when small signals are amplified close to the circuit’s noise floor.
This page combines the exact catalog attributes, package information, sourcing structure, and carefully qualified drop-in alternatives for OPA642PB. It also adds selection guidance and practical implementation notes intended to help engineers distinguish a true pin-compatible replacement from a merely similar amplifier.
Alternativas drop-in para OPA642PB — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com OPA642PB (mesmo formato e footprint) — diferindo em Package, Product Type, Common-Mode Rejection Ratio.
OPA642P
✅ Drop-InConsulte o preço
Ver ficha técnica →OPA641P
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
OPA640P
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →OPA642PB Classificações máximas e características elétricas
| Product Type | Wideband, low-distortion, low-gain operational amplifier |
| Amplifier Architecture | Single voltage-feedback operational amplifier |
| Supply Voltage Range | ±4.5 V to ±5.5 V |
| Single Supply Equivalent Range | 9 V to 11 V |
| Stated Gain Figure | 90 dB |
| Operating Current | 25 uA |
| Corrente de repouso | 70 uA |
| Number of Circuits | 1 circuit |
| Número de pinos | 8 pins |
| Encapsulamento | 8-pin PDIP, 0.300 inch (7.62 mm) pitch |
| Terminal Type | Through-hole |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
Guia de Configuração de Pinos do OPA642PB rectangular
Configuração de pinos para OPA642PB (pacote rectangular). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para OPA642PB.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
OPA642PB é adequado para 6 aplicaçãos: Precision Sensor Signal Conditioning, Communications Receiver Front End, Laboratory Instrumentation, Data Acquisition Front End, Audio and Low-Level Analog Amplification, Industrial Control and Measurement.
Precision Sensor Signal Conditioning
OPA642PB fits low-level sensor front ends that require a wideband amplifier rather than a slow precision-only amplifier. Its single voltage-feedback topology supports straightforward inverting and noninverting configurations, while the ±4.5 V to ±5.5 V operating range accommodates symmetric analog rails around ground. Place the feedback network close to the amplifier and verify the sensor output remains inside the input common-mode range. The low-distortion and low-gain positioning can help preserve small signals before ADC conversion.
Recomendado
Communications Receiver Front End
OPA642PB can amplify receiver signals when the selected gain must preserve bandwidth and limit distortion. Its wideband, low-gain operational-amplifier characterization makes it more relevant than a general-purpose slow amplifier for intermediate-frequency or broadband signal paths. The ±4.5 V to ±5.5 V supply operation supports centered dual-rail analog systems. Validate gain-bandwidth product, slew rate, common-mode range, and output swing against the highest operating frequency before deployment.
Recomendado
Laboratory Instrumentation
OPA642PB is appropriate for laboratory instrumentation where a compact through-hole amplifier can be placed close to sensitive analog circuitry. The 8-pin PDIP package simplifies breadboard and legacy instrument-board assembly, while the wideband low-distortion design supports signal conditioning beyond very slow measurement rates. Use short feedback traces, a solid ground reference, and local supply bypassing. Confirm the exact pinout and suffix-specific temperature limits before finalizing the instrument board.
Recomendado
Data Acquisition Front End
OPA642PB can serve as the gain stage ahead of a data-acquisition converter when low distortion and bandwidth are priorities. Its single-circuit architecture avoids sharing an internal amplifier package with unrelated functions, and the ±4.5 V to ±5.5 V range suits bipolar sensor interfaces. Select the feedback ratio so signal gain remains compatible with the amplifier’s bandwidth and output swing. Route the conditioned output directly toward the converter to minimize added noise and pickup.
Recomendado
Audio and Low-Level Analog Amplification
OPA642PB can amplify low-level audio or control signals when the design values low distortion over the required signal bandwidth. Its instrumentation-style low-gain architecture supports analog preamplification without relying on a high closed-loop gain that could reduce bandwidth or compromise stability. The symmetric supply requirement should be checked against the source and load. Decouple each supply rail near the device and compare the calculated output swing with the signal peak before selecting the feedback network.
Recomendado
Industrial Control and Measurement
OPA642PB can condition low-voltage signals in industrial measurement modules when the system uses symmetric analog rails and requires predictable wideband behavior. The through-hole PDIP package supports panel boards and modular industrial control assemblies. Keep sensitive inputs away from switching nodes and provide a low-impedance return path to the amplifier ground. Because industrial environments can introduce temperature and supply variation, confirm the exact OPA642PB temperature grade, supply tolerances, and output capability in the manufacturer datasheet.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para OPA642PB — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | OPA642P | OPA641P | OPA640P |
|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Family | OPA642 wideband low-distortion operational amplifier | OPA642 family | OPA641 family | OPA640 family |
| Circuit Count | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
Principais diferenciais
- Established wideband low-distortion device positioning (vs OPA641P)
- Documented operating range and current characteristics (vs OPA640P)
- Exact package and single-circuit architecture (vs OPA642P)
Notas de projeto
Place OPA642PB close to the protected signal source and keep both feedback resistors adjacent to the relevant input and output pins. Longer loops around the amplifier can pick up noise and add parasitic capacitance that changes stability or bandwidth. Route the non-inverting input away from supply, clock, and digital return paths, and use a continuous ground reference rather than splitting analog and power grounds under the device.
Decouple each OPA642PB supply rail close to its package connection, and keep the return current associated with bypass capacitors separate from sensitive input returns. The supported operating range is ±4.5 V to ±5.5 V, so verify startup, rail sequencing, and maximum supply conditions in the manufacturer datasheet. If the source signal is referenced to ground, confirm the output can reach the required peak swing before increasing the closed-loop gain.
Do not treat matching the 8-pin PDIP footprint as proof of complete replacement compatibility. Confirm the exact pin functions, offset-null behavior, input common-mode range, output swing, gain-bandwidth product, slew rate, and suffix-specific temperature rating for OPA642P, OPA641P, or OPA640P. After substitution, repeat AC and DC testing across the intended load range because small differences in offset, bias current, or compensation can alter low-level signal accuracy.
Informações de conformidade
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for this ordering code. AEC-Q100 qualification is treated as not applicable because OPA642PB is listed as an industrial-grade operational amplifier rather than an automotive-qualified device.