NXP Semiconductors

PCA9501D - 8-Bit I2C I/O Expander with 2-kbit EEPROM | NXP

MPN: PCA9501D ✓ Aktif
SO20 (SOP-20) surface mount Package 400 kHz Speed 2 kbit (256 bytes) Memory
MOQ: 1 |

PCA9501D Ringkasan

The NXP PCA9501D is an 8-bit I2C-bus and SMBus I/O port expander with an on-board 2-kbit EEPROM, a dedicated interrupt output and six hardware address pins, supplied in a 20-pin SO (SOIC-20) surface-mount package.

An I/O expander (also called a GPIO expander or port expander) is a level-shifting serial-to-parallel interface device that converts a two-wire I2C-bus connection into a bank of individually addressable digital input/output lines. The PCA9501D sits in the hierarchy I/O expander > bus interface IC > interface IC > integrated circuit, and it is designed for designers who have run out of GPIO pins on a microcontroller, logic device or field-programmable gate array and need additional lines without growing the pin count of the main device.

Key features include 8 quasi-bidirectional I/O lines (P0 through P7), an on-board 2-kbit serial EEPROM that the bus master can read and write independently of the I/O port, 6 hardware address pins that allow up to 64 PCA9501 devices to share one I2C bus, and an open-drain interrupt output that alerts the host when any input line changes state. The device operates on the standard I2C/SMBus ecosystem at up to 400 kHz, so it pairs directly with NXP microcontrollers, 3.3 V and 5 V logic families, and energy-harvesting or sensor-hub designs.

Internally, the PCA9501D combines a 256-byte EEPROM array with the parallel port register set. The port lines default to high-impedance inputs and can be reconfigured individually as inputs or quasi-bidirectional outputs with an internal pull-up, which allows a single pin to read a switch and still sink current when driven low. Because the EEPROM is accessed through the same bus as the GPIO register, the bus master sees two separate I2C addresses for one physical device, and the interrupt pin removes the need for continuous polling of slow-changing inputs.

Typical uses include reading banks of push buttons and configuration DIP switches, driving discrete LEDs, relay or solenoid drivers, and level shifters, adding status indicators on industrial control boards, and storing calibration or configuration data in EEPROM without spending a separate memory chip. It is also a common substitute for the PCF8574 in designs that want EEPROM and interrupt support added.

When laying out the board, keep the SDA and SCL traces short, pull both lines up with a resistor in the range of 2.2 kOhm to 10 kOhm, and treat all address pins as static straps that must be tied to VDD or ground before the device is addressed. Confirm the total pull-up budget on the bus so that several expanders can share the same pair of lines.

Alternatif penggantian untuk PCA9501D — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

PCA9501D,112

✅ Drop-In
📦 SO20 (SOP-20)
Identical PCA9501 silicon in the same SO20 body; differs only in catalogue packing format (0% electrical difference)

📋 Alternatif referensi (tidak dalam katalog)

PCA9501D,118

✅ Drop-In
📦 SO20 (SOP-20)
Identical PCA9501 silicon in the same SO20 body with identical 8-bit port, 2-kbit EEPROM and 6 address pins (0% electrical difference)

📋 Alternatif referensi (tidak dalam katalog)

PCA9501D,111

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 SO20 (SOP-20)
Same PCA9501D device in the SO20 body with an alternate tube/bulk-style catalogue code; electrical ratings unchanged (0% difference)

📋 Alternatif referensi (tidak dalam katalog)

PCA9501D Spesifikasi

Device Type 8-bit I2C-bus and SMBus I/O port expander with interrupt and EEPROM
I/O Port Width 8 bit (P0-P7)
Bus Compatibility I2C-bus and SMBus
Maximum Bus Frequency 400 kHz
On-Board EEPROM 2 kbit (256 bytes)
Hardware Address Pins 6 (A0-A5)
Maximum Devices per Bus 64
Interrupt Output Yes, open-drain INT output
Output Port Type Quasi-bidirectional I/O with internal pull-up
Paket SO20 (SOP-20) surface mount
Tipe Mounting Surface Mount
Manufacturer NXP Semiconductors
Status Lingkungan Hidup Active
Ordering Code Suffix D = SO20 package variant

PCA9501D so20 (sop-20) surface mount Diamant Konfigurasi Panduan

Konfigurasi pin untuk PCA9501D (so20 (sop-20) surface mount pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai so20 (sop-20) surface mount untuk PCA9501D

Tidak ada data diatribut pin yang tersedia untuk PCA9501D.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

PCA9501D cocok untuk 6 aplikasis: Industrial Control Panel Switch and LED I/O Expansion, Network Equipment Node Configuration Storage, Multi-Card Telecom and Base Station Systems, General-Purpose Embedded GPIO Expansion, Server and Storage Blade Management Boards, Portable and Battery-Powered Sensor Hubs.

🏭

Industrial Control Panel Switch and LED I/O Expansion

The PCA9501D is a natural fit for front panels and control boards that need more digital lines than the host controller offers. Eight quasi-bidirectional pins can read a bank of limit switches or DIP selectors and simultaneously drive relay, status-LED and solenoid outputs, while the 2-kbit EEPROM stores board-level configuration such as node IDs, panel calibration or the last used menu position so the settings survive a power cycle. Because the device answers on two bus addresses, the master reads the port register and the EEPROM through one I2C pair, and the open-drain INT line lets the microcontroller react to a switch change instead of polling continuously. With 6 hardware address pins available, up to 64 PCA9501D units can be distributed across a multi-panel system.

🌐

Network Equipment Node Configuration Storage

In telecom and networking equipment, the PCA9501D combines port expansion with per-card EEPROM storage in one SO20 footprint. A line card typically needs a handful of interrupt or presence inputs plus a few discrete outputs, and each card also needs a unique address, serial number or configuration blob that must survive power loss and field replacement. The PCA9501D delivers eight I/O lines and 256 bytes of non-volatile storage while consuming only two I2C addresses, so a multi-card chassis can address up to 64 boards without adding address-decoding glue logic. The interrupt output shortens response time for link or alarm events, which matters in line cards that must report a fault within milliseconds.

📡

Multi-Card Telecom and Base Station Systems

The NXP PCA9501 datasheet highlights multi-card systems in telecom, networking and base-station equipment as a target application, and the PCA9501D is the part that supports them. Each card can carry its own PCA9501D as a local I/O and configuration hub, addressing a bus of switches, alarm inputs and card presence detectors while holding card-specific calibration data in the 2-kbit EEPROM. The 6 address pins allow up to 64 devices on one segment, so a base-station rack can scale without redesigning the backplane interconnect. Field recall and troubleshooting of installed boards is simplified because the EEPROM retains node identity and configuration for maintenance staff, and the 400 kHz bus rate keeps configuration reads fast during boot.

🧩

General-Purpose Embedded GPIO Expansion

Embedded designs that exhaust the GPIO budget of a microcontroller can extend their digital I/O count with the PCA9501D instead of changing the host package. A typical embedded controller has a handful of free pins after routing the serial console, status indicators and a few sensors; adding one PCA9501D brings eight more lines over the same two-wire bus, and the accompanying 2-kbit EEPROM removes the need for a separate memory chip when configuration values such as radio channel, unit serial number or calibration offsets must persist. Quasi-bidirectional pins support both read and drive duties on the same net, so a single pin can monitor a push button and still sink LED current when driven low, which saves both board area and pin count.

🖥️

Server and Storage Blade Management Boards

Blade and rack management controllers rely on dense, low-cost GPIO for presence detection, fan control and fault signalling, and the PCA9501D fits that role well. A single expander can capture chassis intrusion switches, drive amber and blue fault LEDs and store the blade's asset tag or calibration data in the 2-kbit EEPROM, all behind one 400 kHz I2C link shared with other low-speed management traffic. The open-drain interrupt output lets the baseboard management controller sleep between events, cutting standby power, and the EEPROM-backed address means dozens of blades can share a bus without per-blade resistor straps. Add a PCA9501D next to the hot-swap controller outputs to keep the management wiring short and the GPIO count predictable.

📱

Portable and Battery-Powered Sensor Hubs

Battery-operated sensor hubs benefit from the PCA9501D because a single low-power I2C bus can carry both the sensing interface and the storage needed for calibration. The 2-kbit EEPROM holds per-unit calibration constants and node identity without drawing current, and the interrupt output lets the host MCU stay in a deep sleep until a door switch or threshold comparator actually changes, which directly extends standby time. Because the expander answers on two bus addresses, the host can read the port register on demand and read or write the configuration block without adding a second serial memory chip to the board. The interrupt output is open-drain, so several PCA9501D devices on one bus can share a single host interrupt line.

Ringkasan Produk Direkomendasikan

STM32G071GBU6TR STMicroelectronics Digunakan di dalam: Industrial Control Panel Switch and LED I/O Expansion TJA1057GTK/3Z NXP Semiconductors Digunakan di dalam: Industrial Control Panel Switch and LED I/O Expansion KSZ8041RNACA Ethernet PHY for networked control panels Digunakan di dalam: Industrial Control Panel Switch and LED I/O Expansion LAN7500I-ABZJ-TR Microchip Technology Digunakan di dalam: Network Equipment Node Configuration Storage KSZ8041TLI-TR Microchip Technology Digunakan di dalam: Network Equipment Node Configuration Storage Z86E4412ASG Zilog Digunakan di dalam: Network Equipment Node Configuration Storage KSZ8001LA2TR Microchip Technology Digunakan di dalam: Multi-Card Telecom and Base Station Systems LAN9313I-NZW-TR Microchip Technology Digunakan di dalam: Multi-Card Telecom and Base Station Systems KSZ8041MLL-TR Microchip Technology Digunakan di dalam: Multi-Card Telecom and Base Station Systems STM32G031J6M6TR STMicroelectronics Digunakan di dalam: General-Purpose Embedded GPIO Expansion ATMEGA8U2-AUR Microchip Technology Digunakan di dalam: General-Purpose Embedded GPIO Expansion MC14C88BP onsemi Digunakan di dalam: General-Purpose Embedded GPIO Expansion LAN9730-ABZJ-TR Microchip Technology Digunakan di dalam: Server and Storage Blade Management Boards STM32G474VET6TR STMicroelectronics Digunakan di dalam: Server and Storage Blade Management Boards KSZ8895FMQTR Microchip Technology Digunakan di dalam: Server and Storage Blade Management Boards STM32G030K6T6TR STMicroelectronics Digunakan di dalam: Portable and Battery-Powered Sensor Hubs ATTINY44A-MUR Microchip Technology Digunakan di dalam: Portable and Battery-Powered Sensor Hubs INA149AIDR Texas Instruments Digunakan di dalam: Portable and Battery-Powered Sensor Hubs
What is the PCA9501D?
The NXP PCA9501D is an 8-bit I2C-bus and SMBus I/O port expander that combines 8 quasi-bidirectional GPIO lines, an on-board 2-kbit EEPROM and an open-drain interrupt output in a single 20-pin SO (SOIC-20) package. According to the NXP PCA9501 datasheet, the device lets one I2C bus address up to 64 separate expanders using 6 hardware address pins, and the bus master accesses the GPIO register and the EEPROM as two distinct I2C addresses. It is used wherever a microcontroller, FPGA or logic device needs more digital lines than its own pin count allows.
How many PCA9501 devices can share one I2C bus?
Up to 64 PCA9501 devices can share a single I2C bus. The device exposes 6 hardware address pins (A0 through A5), and each combination of strap levels selects a different 7-bit I2C address. Per the NXP PCA9501 datasheet, the address pins are sampled at power-on and are 2 kbit EEPROM backed, so the device keeps its bus identity even after a power cycle. Each expander occupies two I2C addresses on the bus: one for the 8-bit I/O port register set and one for the 2-kbit EEPROM.
Can the PCA9501D replace a PCF8574?
The PCA9501D is a functional upgrade over the PCF8574 because it adds a 2-kbit EEPROM and an interrupt output to the same 8-bit quasi-bidirectional port. The NXP datasheet explicitly lists replacement for PCF8574 with integrated 2-kbit EEPROM as an intended application. Two differences matter in practice: the PCF8574 address pins are typically tied to ground with no EEPROM behind them, whereas the PCA9501D keeps address settings in EEPROM, and the PCA9501D adds an INT line so the host does not have to poll the port register continuously.
What is the 2-kbit EEPROM inside the PCA9501D used for?
The 2-kbit (256-byte) on-board EEPROM is a general-purpose serial memory that the I2C master can read and write using the standard device address. Per the NXP PCA9501 datasheet, the EEPROM holds configuration data, and because it is non-volatile it retains board settings such as jumper positions, calibration coefficients or node addresses across power cycles. The EEPROM is also what backs the device address straps, so each unit keeps a unique bus address without external resistors being re-soldered.
What is the maximum I2C bus speed of the PCA9501D?
The PCA9501D supports I2C-bus and SMBus operation at up to 400 kHz, as listed on distributor product pages and in the NXP PCA9501 datasheet. At that rate a full 256-byte EEPROM page transfer completes quickly enough that configuration data can be refreshed inside a short control loop. In practice the achievable speed on a board is limited by bus capacitance, pull-up resistor selection and the speed rating of the host microcontroller, so the 400 kHz figure should be treated as a device ceiling rather than a guarantee.
Where can I download the PCA9501 datasheet PDF?
The official NXP datasheet PDF for the PCA9501 family is available from the NXP document centre at https://www.nxp.com/docs/en/data-sheet/PCA9501.pdf, and the family product page is at https://www.nxp.com/part/PCA9501D. The NXP document includes the pin description table, the functional description of the port registers, the EEPROM access sequence and the address-selection truth table. Use the pin description table when assigning PCB nets, since the PCA9501D is the SO20 package variant of the family.
Where can I find the PCA9501D pinout?
The authoritative pin assignment is in the NXP PCA9501 datasheet, in the pin description table for the SO20 package option. The PCA9501D is the 20-pin SO (SOP-20) variant of the PCA9501 family, with the I2C pins, the six address pins, the interrupt output, supply and ground alongside the 8 port lines. Assign tracks from that table rather than from a generic 20-pin drawing, because the same family also ships in a TSSOP-20 variant whose pin functions match but whose body size differs.
What is the difference between PCA9501D and PCA9501PW?
The PCA9501D and PCA9501PW are the same PCA9501 silicon offered in different packages: the D suffix denotes the SO20 (SOP-20) body while the PW suffix denotes the smaller TSSOP-20 body. Pin functions are equivalent, but the footprints are not, so a PW part will not drop into a D footprint without a board change. When comparing PCB space against assembly cost for a new design, check the land pattern of the SO20 pad spacing before deciding between the two variants.
PCA9501D vs PCA9501D,118 - which orderable suffix should I pick?
The PCA9501D,112 and PCA9501D,118 order codes are both catalogue listings of the same PCA9501D device in the 20-pin SO package, and the functional content is identical. The difference is packing and reel format rather than electrical behaviour, so both can be fitted on the same PCA9501D footprint. Choose the variant that matches the reel width and volume your assembly line expects, and use the Request a Quote form on this page if you need confirmation of reel and cut-tape quantities for your build.
What can replace the PCA9501D?
The most direct replacement is another PCA9501D order code such as PCA9501D,112 or PCA9501D,118, which is the identical device in a different catalogue packing format. For a genuine footprint-compatible swap, the SO20 body and pin functions must match, so verify the land pattern and the pin description table before committing. If your design does not actually need the EEPROM and interrupt, a plain 8-bit I2C GPIO expander in the same SO20 footprint can substitute, but that is a functional rather than a pin-for-pin match.
Is the PCA9501D the same as a PCA9554?
No. The PCA9501D adds a 2-kbit EEPROM, an interrupt output and 6 hardware address pins to the 8-bit I/O port, while the PCA9554 is a plain 8-bit quasi-bidirectional I2C GPIO expander without the on-chip memory or the INT pin. Both sit on the same 400 kHz I2C ecosystem, but the PCA9501D needs two bus addresses per chip and provides a change notification, so it fits designs with configuration data to store or inputs that should not be polled.
When should I choose the PCA9501D instead of a plain GPIO expander?
Choose the PCA9501D when your board needs three things at once: more digital lines than the host device has spare pins, non-volatile per-board configuration data, and an interrupt so the host is not busy-polling slow inputs. The 2-kbit EEPROM holds calibration or node-ID values across power cycles, and the INT line wakes the microcontroller on any input change, which matters for battery-powered nodes. If you only need extra output lines, a simpler GPIO expander is smaller and cheaper per channel.
Is the PCA9501D suitable for industrial and automotive control boards?
The PCA9501D is widely used on industrial and telecom control boards for reading switch banks and driving indicator LEDs, and its EEPROM is useful for storing board-level configuration and node addresses. Confirm the exact supply voltage range, junction temperature limits and any AEC-Q100 qualification for the specific ordering code before using it in an automotive environment, since the manufacturer datasheet, not the distributor listing, defines those limits. Use the Request a Quote form on this page to confirm grade and temperature options.
Where can I buy PCA9501D parts online?
You can request a quote for the NXP PCA9501D directly through the Request a Quote form on this page, which is the fastest way to check stock, reel quantities and lead time for the SO20 ordering codes you need. Live inventory and pricing for this part move daily across authorised channels, so the form gives a current answer for the exact part number and pack format you are building with. Share your target quantity, reel format and required delivery date with the response.
What is the price of the PCA9501D?
Pricing for the PCA9501D is best obtained through the Request a Quote form on this page rather than from a static table, because unit prices move with volume, reel format and current supply of the NXP order codes such as PCA9501D,112 and PCA9501D,118. Submitting your quantity and required delivery date returns a current quote for the exact suffix you plan to assemble with, including any reel or cut-tape packaging you need.
What is the lead time and stock status for the PCA9501D?
Lead time for the PCA9501D depends on the ordering code and the volume you need, so the current position should be confirmed through the Request a Quote form on this page. In that form specify whether you need PCA9501D,112, PCA9501D,118 or a cut-tape quantity, plus your production schedule. Because the part is an interface IC with a standard NXP catalogue footprint, production planning is usually straightforward once the exact suffix and quantity are confirmed in writing.
What are the key specifications of the PCA9501D that engineers should know?
The NXP PCA9501D is an 8-bit I2C-bus and SMBus I/O port expander with a 2-kbit on-board EEPROM, an interrupt output and 6 hardware address pins, packed in a 20-pin SO (SOIC-20) surface-mount package. It runs at up to 400 kHz on the I2C bus, allows up to 64 devices to share one bus, and presents the GPIO register and the EEPROM as two separate bus addresses. The port pins are quasi-bidirectional with internal pull-ups, and the address settings are backed by the EEPROM so node identity survives a power cycle.
What does the interrupt pin on the PCA9501D do?
The INT pin on the PCA9501D is an open-drain output that pulls low when any of the 8 input lines changes state, letting the host microcontroller react immediately instead of polling the port register. Combined with the 6 address pins, this makes multi-node designs scale cleanly: each expander can flag its own change and the master only reads the register that actually changed. Because the output is open-drain, several interrupt sources can share one host pin, or a pull-up can be added to form a wired-AND bus.

Data referensi engineering untuk PCA9501D — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the PCA9501D when your design needs three things at once: extra digital lines beyond the host device pin budget, per-board non-volatile configuration, and event notification. The 2-kbit EEPROM retains calibration values, node addresses and jumper settings across power cycles, and the open-drain interrupt lets a low-power MCU sleep until an input actually changes. It is a common upgrade path for PCF8574-based designs that later need memory and change notification, and it fits multi-card telecom, industrial panel and blade-management boards where up to 64 expanders share one 400 kHz bus. Pick a plain 8-bit GPIO expander instead when you only need extra outputs and no storage or notification, since it is cheaper per channel and simpler to drive. Select the SO20 PCA9501D when the existing land pattern is the 20-pin SO body; the TSSOP-20 PCA9501PW option shares the pin functions but requires a different footprint. For new boards, verify supply voltage range, temperature limits and any automotive qualification in the NXP datasheet, and confirm reel format and lead time for the exact ordering code.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini PCA9501D,112 PCA9501D,118 PCA9501D,111
Package SO20 (SOP-20) SO20 (SOP-20) - same SO20 (SOP-20) - same SO20 (SOP-20) - same
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
I/O Port Width 8 bit (P0-P7) 8 bit (P0-P7) 8 bit (P0-P7) 8 bit (P0-P7)
On-Board EEPROM 2 kbit (256 bytes) 2 kbit (256 bytes) 2 kbit (256 bytes) 2 kbit (256 bytes)
Address Pins 6 (A0-A5), up to 64 devices per bus 6 (A0-A5), up to 64 devices per bus 6 (A0-A5), up to 64 devices per bus 6 (A0-A5), up to 64 devices per bus
Interrupt Output Yes, open-drain INT Yes, open-drain INT Yes, open-drain INT Yes, open-drain INT
Maximum Bus Frequency 400 kHz 400 kHz 400 kHz 400 kHz
Bus Protocol I2C-bus and SMBus I2C-bus and SMBus I2C-bus and SMBus I2C-bus and SMBus
Catalogue Packing Format Base MPN listing SO20 catalogue code SO20 tape-and-reel catalogue code SO20 bulk/tube-style catalogue code

Diferensiator Kunci

  • Combines GPIO expansion with on-board non-volatile storage in one package (vsPCA9554)
  • Interrupt output removes continuous bus polling (vsPCA9554)
  • Six hardware address pins support large multi-node buses (vsPCA9501PW,112)

Catatan Desain

Route SDA and SCL as short, direct traces between the host MCU and the PCA9501D, keeping the pair away from switching nodes and high-current traces. Place the bus pull-up resistors physically at the point where the bus is driven, ideally near the master device, and size them between about 2.2 kOhm and 10 kOhm so that rise times meet the 400 kHz target. The six address pins are static straps: tie each of A0 through A5 directly to VDD or GND with a short trace and no shared test pads, because added capacitance on these inputs can upset strap sampling at power-on.

Budget the PCA9501D supply rail carefully when the design runs from a switched 5 V or 3.3 V rail. The device needs a stable local rail because its internal pull-ups on the quasi-bidirectional port lines reference VDD; if the rail dips, the port reads can become indeterminate. Place a 100 nF ceramic decoupling capacitor close to the VDD pin and add a bulk capacitor of a few microfarads nearby if the port lines sink significant LED or relay current. Confirm the absolute maximum supply voltage and the operating supply range in the NXP PCA9501 datasheet before connecting to a 5 V industrial rail with transients.

Two mistakes account for most PCA9501D bring-up failures. First, the GPIO register and the EEPROM occupy two different I2C addresses, so driver code that treats the part as a single-address device reads back zeros or stale configuration bytes; address them separately. Second, quasi-bidirectional port lines are inputs with an internal pull-up until they are written low, so a pin driving a load must be explicitly driven high or low at start-up or it will float at the pull-up level. Add a third check that the INT output needs its own pull-up to VDD, since the pin is open-drain and leaves the host interrupt line undriven if no pull-up is fitted.

Avoid substituting the PCA9501PW, TSSOP-20 variant for the PCA9501D on an existing board. The two share pin functions but not the land pattern, so the SO20 footprint will not accept the TSSOP body and the change requires a new board. Confirm the ordering suffix on the reel against the package drawing before kitting a build, since PCA9501D,112, PCA9501D,118 and the SO20 family codes all refer to the same 20-pin body with different packing formats and are otherwise electrically identical.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

No RoHS, REACH or AEC-Q100 statements were present in the manufacturer and distributor pages for this part; confirm compliance and automotive grade with the NXP datasheet and the Request a Quote form before release.

Data disahkan pada: 2026-11-14 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

pca9501 datasheet pca9501 nxp pca9501 pdf PCA9501D datasheet PCA9501D pinout PCA9501D SO20 pinout PCA9501 8-bit I2C I/O expander EEPROM PCA9501D vs PCA9554 PCA9501D replacement equivalent PCA9501D 400 kHz SMBus address pins PCA9501D PCF8574 replacement PCA9501D I/O expander industrial control PCA9501D buy price stock PCA9501D interrupt output EEPROM configuration

Komponen dan Istilah Terkait

NXP Semiconductors PCA9501 PCA9501D PCA9501D,112 PCA9501D,118 PCA9501PW,112 PCA9554 PCF8574 I/O expander GPIO expander port expander quasi-bidirectional I/O port I2C-bus SMBus I2C serial EEPROM 2-kbit EEPROM interrupt output hardware address pins SO20 (SOP-20) TSSOP-20 surface mount 400 kHz I2C multi-card telecom systems industrial control panel
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ