PCA9501D - 8-Bit I2C I/O Expander with 2-kbit EEPROM | NXP
MPN: PCA9501D ✓ AktifPCA9501D Ringkasan
An I/O expander (also called a GPIO expander or port expander) is a level-shifting serial-to-parallel interface device that converts a two-wire I2C-bus connection into a bank of individually addressable digital input/output lines. The PCA9501D sits in the hierarchy I/O expander > bus interface IC > interface IC > integrated circuit, and it is designed for designers who have run out of GPIO pins on a microcontroller, logic device or field-programmable gate array and need additional lines without growing the pin count of the main device.
Key features include 8 quasi-bidirectional I/O lines (P0 through P7), an on-board 2-kbit serial EEPROM that the bus master can read and write independently of the I/O port, 6 hardware address pins that allow up to 64 PCA9501 devices to share one I2C bus, and an open-drain interrupt output that alerts the host when any input line changes state. The device operates on the standard I2C/SMBus ecosystem at up to 400 kHz, so it pairs directly with NXP microcontrollers, 3.3 V and 5 V logic families, and energy-harvesting or sensor-hub designs.
Internally, the PCA9501D combines a 256-byte EEPROM array with the parallel port register set. The port lines default to high-impedance inputs and can be reconfigured individually as inputs or quasi-bidirectional outputs with an internal pull-up, which allows a single pin to read a switch and still sink current when driven low. Because the EEPROM is accessed through the same bus as the GPIO register, the bus master sees two separate I2C addresses for one physical device, and the interrupt pin removes the need for continuous polling of slow-changing inputs.
Typical uses include reading banks of push buttons and configuration DIP switches, driving discrete LEDs, relay or solenoid drivers, and level shifters, adding status indicators on industrial control boards, and storing calibration or configuration data in EEPROM without spending a separate memory chip. It is also a common substitute for the PCF8574 in designs that want EEPROM and interrupt support added.
When laying out the board, keep the SDA and SCL traces short, pull both lines up with a resistor in the range of 2.2 kOhm to 10 kOhm, and treat all address pins as static straps that must be tied to VDD or ground before the device is addressed. Confirm the total pull-up budget on the bus so that several expanders can share the same pair of lines.
Pilihan pengganti yang segera untuk PCA9501D — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
PCA9501D,112
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
PCA9501D,118
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
PCA9501D,111
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
PCA9501D Spesifikasi
| Device Type | 8-bit I2C-bus and SMBus I/O port expander with interrupt and EEPROM |
| I/O Port Width | 8 bit (P0-P7) |
| Bus Compatibility | I2C-bus and SMBus |
| Maximum Bus Frequency | 400 kHz |
| On-Board EEPROM | 2 kbit (256 bytes) |
| Hardware Address Pins | 6 (A0-A5) |
| Maximum Devices per Bus | 64 |
| Interrupt Output | Yes, open-drain INT output |
| Output Port Type | Quasi-bidirectional I/O with internal pull-up |
| Kemasan | SO20 (SOP-20) surface mount |
| Jenis Pemasangan | Surface Mount |
| Manufacturer | NXP Semiconductors |
| Status Lingkungan Hidup | Active |
| Ordering Code Suffix | D = SO20 package variant |
Panduan Konfigurasi Pin PCA9501D so20 (sop-20) surface mount
Konfigurasi pin untuk PCA9501D (so20 (sop-20) surface mount pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk PCA9501D.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
PCA9501D patut untuk 6 aplikasis: Industrial Control Panel Switch and LED I/O Expansion, Network Equipment Node Configuration Storage, Multi-Card Telecom and Base Station Systems, General-Purpose Embedded GPIO Expansion, Server and Storage Blade Management Boards, Portable and Battery-Powered Sensor Hubs.
Industrial Control Panel Switch and LED I/O Expansion
The PCA9501D is a natural fit for front panels and control boards that need more digital lines than the host controller offers. Eight quasi-bidirectional pins can read a bank of limit switches or DIP selectors and simultaneously drive relay, status-LED and solenoid outputs, while the 2-kbit EEPROM stores board-level configuration such as node IDs, panel calibration or the last used menu position so the settings survive a power cycle. Because the device answers on two bus addresses, the master reads the port register and the EEPROM through one I2C pair, and the open-drain INT line lets the microcontroller react to a switch change instead of polling continuously. With 6 hardware address pins available, up to 64 PCA9501D units can be distributed across a multi-panel system.
Disebarkan
Network Equipment Node Configuration Storage
In telecom and networking equipment, the PCA9501D combines port expansion with per-card EEPROM storage in one SO20 footprint. A line card typically needs a handful of interrupt or presence inputs plus a few discrete outputs, and each card also needs a unique address, serial number or configuration blob that must survive power loss and field replacement. The PCA9501D delivers eight I/O lines and 256 bytes of non-volatile storage while consuming only two I2C addresses, so a multi-card chassis can address up to 64 boards without adding address-decoding glue logic. The interrupt output shortens response time for link or alarm events, which matters in line cards that must report a fault within milliseconds.
Disebarkan
Multi-Card Telecom and Base Station Systems
The NXP PCA9501 datasheet highlights multi-card systems in telecom, networking and base-station equipment as a target application, and the PCA9501D is the part that supports them. Each card can carry its own PCA9501D as a local I/O and configuration hub, addressing a bus of switches, alarm inputs and card presence detectors while holding card-specific calibration data in the 2-kbit EEPROM. The 6 address pins allow up to 64 devices on one segment, so a base-station rack can scale without redesigning the backplane interconnect. Field recall and troubleshooting of installed boards is simplified because the EEPROM retains node identity and configuration for maintenance staff, and the 400 kHz bus rate keeps configuration reads fast during boot.
Disebarkan
General-Purpose Embedded GPIO Expansion
Embedded designs that exhaust the GPIO budget of a microcontroller can extend their digital I/O count with the PCA9501D instead of changing the host package. A typical embedded controller has a handful of free pins after routing the serial console, status indicators and a few sensors; adding one PCA9501D brings eight more lines over the same two-wire bus, and the accompanying 2-kbit EEPROM removes the need for a separate memory chip when configuration values such as radio channel, unit serial number or calibration offsets must persist. Quasi-bidirectional pins support both read and drive duties on the same net, so a single pin can monitor a push button and still sink LED current when driven low, which saves both board area and pin count.
Disebarkan
Server and Storage Blade Management Boards
Blade and rack management controllers rely on dense, low-cost GPIO for presence detection, fan control and fault signalling, and the PCA9501D fits that role well. A single expander can capture chassis intrusion switches, drive amber and blue fault LEDs and store the blade's asset tag or calibration data in the 2-kbit EEPROM, all behind one 400 kHz I2C link shared with other low-speed management traffic. The open-drain interrupt output lets the baseboard management controller sleep between events, cutting standby power, and the EEPROM-backed address means dozens of blades can share a bus without per-blade resistor straps. Add a PCA9501D next to the hot-swap controller outputs to keep the management wiring short and the GPIO count predictable.
Disebarkan
Portable and Battery-Powered Sensor Hubs
Battery-operated sensor hubs benefit from the PCA9501D because a single low-power I2C bus can carry both the sensing interface and the storage needed for calibration. The 2-kbit EEPROM holds per-unit calibration constants and node identity without drawing current, and the interrupt output lets the host MCU stay in a deep sleep until a door switch or threshold comparator actually changes, which directly extends standby time. Because the expander answers on two bus addresses, the host can read the port register on demand and read or write the configuration block without adding a second serial memory chip to the board. The interrupt output is open-drain, so several PCA9501D devices on one bus can share a single host interrupt line.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk PCA9501D — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | PCA9501D,112 | PCA9501D,118 | PCA9501D,111 |
|---|---|---|---|---|
| Package | SO20 (SOP-20) | SO20 (SOP-20) - same | SO20 (SOP-20) - same | SO20 (SOP-20) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| I/O Port Width | 8 bit (P0-P7) | 8 bit (P0-P7) | 8 bit (P0-P7) | 8 bit (P0-P7) |
| On-Board EEPROM | 2 kbit (256 bytes) | 2 kbit (256 bytes) | 2 kbit (256 bytes) | 2 kbit (256 bytes) |
| Address Pins | 6 (A0-A5), up to 64 devices per bus | 6 (A0-A5), up to 64 devices per bus | 6 (A0-A5), up to 64 devices per bus | 6 (A0-A5), up to 64 devices per bus |
| Interrupt Output | Yes, open-drain INT | Yes, open-drain INT | Yes, open-drain INT | Yes, open-drain INT |
| Maximum Bus Frequency | 400 kHz | 400 kHz | 400 kHz | 400 kHz |
| Bus Protocol | I2C-bus and SMBus | I2C-bus and SMBus | I2C-bus and SMBus | I2C-bus and SMBus |
| Catalogue Packing Format | Base MPN listing | SO20 catalogue code | SO20 tape-and-reel catalogue code | SO20 bulk/tube-style catalogue code |
Penyeberangsung Jelas
- Combines GPIO expansion with on-board non-volatile storage in one package (vsPCA9554)
- Interrupt output removes continuous bus polling (vsPCA9554)
- Six hardware address pins support large multi-node buses (vsPCA9501PW,112)
Catatan Desain
Route SDA and SCL as short, direct traces between the host MCU and the PCA9501D, keeping the pair away from switching nodes and high-current traces. Place the bus pull-up resistors physically at the point where the bus is driven, ideally near the master device, and size them between about 2.2 kOhm and 10 kOhm so that rise times meet the 400 kHz target. The six address pins are static straps: tie each of A0 through A5 directly to VDD or GND with a short trace and no shared test pads, because added capacitance on these inputs can upset strap sampling at power-on.
Budget the PCA9501D supply rail carefully when the design runs from a switched 5 V or 3.3 V rail. The device needs a stable local rail because its internal pull-ups on the quasi-bidirectional port lines reference VDD; if the rail dips, the port reads can become indeterminate. Place a 100 nF ceramic decoupling capacitor close to the VDD pin and add a bulk capacitor of a few microfarads nearby if the port lines sink significant LED or relay current. Confirm the absolute maximum supply voltage and the operating supply range in the NXP PCA9501 datasheet before connecting to a 5 V industrial rail with transients.
Two mistakes account for most PCA9501D bring-up failures. First, the GPIO register and the EEPROM occupy two different I2C addresses, so driver code that treats the part as a single-address device reads back zeros or stale configuration bytes; address them separately. Second, quasi-bidirectional port lines are inputs with an internal pull-up until they are written low, so a pin driving a load must be explicitly driven high or low at start-up or it will float at the pull-up level. Add a third check that the INT output needs its own pull-up to VDD, since the pin is open-drain and leaves the host interrupt line undriven if no pull-up is fitted.
Avoid substituting the PCA9501PW, TSSOP-20 variant for the PCA9501D on an existing board. The two share pin functions but not the land pattern, so the SO20 footprint will not accept the TSSOP body and the change requires a new board. Confirm the ordering suffix on the reel against the package drawing before kitting a build, since PCA9501D,112, PCA9501D,118 and the SO20 family codes all refer to the same 20-pin body with different packing formats and are otherwise electrically identical.
Maklumat Kesediaan
No RoHS, REACH or AEC-Q100 statements were present in the manufacturer and distributor pages for this part; confirm compliance and automotive grade with the NXP datasheet and the Request a Quote form before release.