NXP Semiconductors

PCA9515D - 2-Channel 400 kHz I2C Bus Repeater | NXP

MPN: PCA9515D ✗ Akhir Hidup
8-pin SOIC, 3.90 mm width Package 400 kHz Speed
MOQ: 1 |

PCA9515D Ringkasan

NXP PCA9515D is a 2-channel I2C-bus and SMBus repeater designed to extend a serial bus by buffering the clock and data conductors. The device supports operation up to 400 kHz, provides separate upstream and downstream SDA and SCL paths, and enables two 400 pF bus segments. It is packaged in an 8-pin SOIC surface-mount package. The NXP product page identifies the PCA9515D as no longer manufactured.

An I2C bus repeater is a signal-conditioning interface used when cable length, bus capacitance, loading, or voltage differences prevent a controller from reliably driving a distant I2C target. In the broader hierarchy, the PCA9515D is an I2C interface repeater within the I2C interface IC category. It allows a master to communicate through one buffered bus segment while isolating that segment from the electrical loading of another segment.

The principal feature is bidirectional buffering of both I2C clock and data lines. According to the NXP manufacturer datasheet, each supported bus arrangement accommodates 400 pF, while the operating frequency reaches 400 kHz. Bidirectional operation permits the controller to address devices on either side of the repeater without changing the I2C protocol. A standard-mode-capable architecture is useful for industrial control, sensor networks, embedded systems, and legacy peripheral expansion where greater speed is unnecessary.

Technically, the PCA9515D is a BiCMOS integrated circuit intended for I2C-bus and SMBus systems. BiCMOS construction combines bipolar and CMOS transistor functions, supporting the interface's bidirectional signal path while maintaining low-power operation. Its two-channel arrangement provides one input-side and one output-side connection for SDA and SCL, creating a controlled separation between bus segments rather than simply adding another capacitive load.

Typical uses include extending a controller connection to remote sensors, isolating a high-load I2C segment, and linking two PCB zones that require separate routing or bus termination. It can also support SMBus-style management buses operating at compatible standard-mode rates. The principal design constraint is ensuring that every side of the repeater remains within its allowed capacitance and that pull-up resistors suit the local voltage and current requirements.

For implementation, place the repeater between the two bus sections and connect the downstream SDA and SCL conductors to the corresponding buffer pins. Provide the supply decoupling recommended by the manufacturer datasheet, and confirm that pull-up resistor values account for the separate cable capacitance of both bus segments. Review the enable behavior and bus contention conditions before using the device in a design that requires hot-plug behavior.

This product page combines the manufacturer lifecycle status, bus-function details, package information, sourcing guidance, and engineering-focused replacement analysis. It also identifies the limits of the available drop-in alternatives, helping designers distinguish electrically equivalent order variants from true pin-compatible replacements before modifying an existing PCB.

Alternatif penggantian untuk PCA9515D — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

PCA9515DP

✅ Drop-In
📦 SOIC-8
Same 2-channel, 400 kHz repeater function and 400 pF-per-segment capability; ordering code differs by one packaging suffix, with 0% change to the stated key bus parameters

📋 Alternatif referensi (tidak dalam katalog)

PCA9515AD,118

✅ Drop-In
📦 SOIC-8
Same PCA9515-family 2-channel I2C repeater architecture in 8-pin SOIC; functional characteristics are reported as similar, while the A-series ordering code requires final electrical-limit verification

📋 Alternatif referensi (tidak dalam katalog)

PCA9515D Spesifikasi

Product Type 2-channel I2C-bus and SMBus repeater
Supported Bus I2C-bus and SMBus
Channel Count 2 channels
Maximum Bus Frequency 400 kHz
Bus Capacitance per Segment 400 pF
Buffered Signals SDA and SCL
Signal Direction Bidirectional
Logic Technology BiCMOS
Paket 8-pin SOIC, 3.90 mm width
Tipe Mounting Surface mount
Suhu Kerja -40 °C to 85 °C
I2C Maximum Bus Capacitance 400 pF per bus segment

Konfigurasi Pin PCA9515D

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin produk 1 SCL1 — Bidirectional clock input for the first bus segment
Pin produk 2 SDA1 — Bidirectional data input for the first bus segment
Pin produk 3 SCL2 — Bidirectional clock output for the second bus segment
Pin produk 4 GND — Ground connection
Pin produk 5 SDA2 — Bidirectional data output for the second bus segment
Pin produk 6 EN — Repeater enable input
Pin produk 7 NC — Not connected
Pin produk 8 VDD — Positive supply connection

Aplikasi Umum

PCA9515D cocok untuk 6 aplikasis: Remote Sensor Bus Extension, Industrial Control Module, SMBus Management Segmentation, PCB Bus-Zone Isolation, Embedded Peripheral Expansion, Instrumentation and Test Equipment.

🧩

Remote Sensor Bus Extension

The PCA9515D fits a remote standard-mode sensor bus when the controller and sensors are separated by cable, wiring, or distributed PCB routing. It buffers both SDA and SCL bidirectionally and separates the bus into two sections, each of which may support up to 400 pF according to the NXP manufacturer datasheet. This architecture is useful because a long cable behaves as distributed capacitance and can slow SCL edges enough to violate timing. The repeater must be placed at the boundary between the two segments, with pull-up networks selected for each segment's voltage and capacitance. Its 400 kHz maximum rate supports standard-mode sensors without requiring the faster operating mode of a modern I2C controller.

🏭

Industrial Control Module

The PCA9515D is useful in an industrial control module where an I2C controller must reach sensors or actuator drivers across separately routed board regions. The device's bidirectional 2-channel structure supports clock and data, while its 400 pF-per-segment rating provides room for distributed wiring and peripheral loading. At the maximum specified 400 kHz, however, pull-up resistance and total capacitance must still be checked for acceptable rise time. Galvanic isolation, level translation, and surge protection remain separate functions and should not be inferred from this repeater. Its 8-pin SOIC package also makes it practical for compact controller boards where a full bus-hub or switch IC would add unnecessary functionality.

🖥️

SMBus Management Segmentation

The PCA9515D can segment an SMBus management connection by buffering the SDA and SCL conductors between a host and downstream management devices. The NXP manufacturer datasheet explicitly identifies SMBus as an intended application and describes the device as a 2-channel BiCMOS repeater. Bidirectional pass-through operation allows the host to address devices on either bus side through one logical bus, while the separation reduces accumulated loading. The host and target devices must use compatible logic levels and the entire path must stay within the 400 kHz maximum frequency. Designers should also review the device's enable and startup behavior when peripherals can be connected, powered, or removed during system operation.

🔧

PCB Bus-Zone Isolation

The PCA9515D provides a controlled boundary between two PCB bus zones that cannot be treated as one continuous I2C network. Each side can accommodate up to 400 pF, so a board can place a repeater near a zone boundary and route each section according to its own loading. This helps isolate long routed traces, cable connectors, and clustered sensor groups from the controller's direct bus load. The buffered path remains bidirectional, preserving normal command and response traffic without a separate direction-control signal. Layout should keep the upstream and downstream routes physically distinct, use a solid ground reference, and follow the manufacturer's recommended supply bypass arrangement so switching noise does not couple into the buffered signals.

⚡

Embedded Peripheral Expansion

The PCA9515D can extend an embedded processor's I2C connection to a bank of sensors, EEPROMs, or other low-speed peripherals. The processor continues to use a single logical address space while the repeater separates upstream and downstream loading, allowing each bus section to approach the specified 400 pF limit. At 400 kHz, cable and connector capacitance can materially affect rise time, so the designer should calculate pull-up current for both sections rather than reusing the original bus values unchanged. The device's 8-pin SOIC footprint is convenient for space-constrained control boards, but its no-longer-manufactured status requires lifecycle planning or qualification of a confirmed alternative.

📺

Instrumentation and Test Equipment

The PCA9515D is suitable for instrumentation or test equipment that divides low-speed I2C control traffic between a controller card and a remote fixture. Its separate buffered sections help prevent one cable-connected fixture from loading the entire internal bus, while the 400 kHz limit aligns with many sensors, DACs, and display controllers used in measurement systems. For bench equipment, verify ground offsets, connector leakage, and pull-up voltage before enabling communication because the repeater buffers signals but does not provide isolation. Its bidirectional SDA and SCL channels preserve the normal I2C transaction sequence. The 400 pF budget per side should include fixture cables, adapters, protection devices, and every attached peripheral to avoid an unmodeled rise-time penalty.

What is the PCA9515D used for?
The PCA9515D is a 2-channel I2C-bus and SMBus repeater used to extend a controller connection by buffering the SDA and SCL lines. According to the NXP manufacturer datasheet, it supports two bus segments of 400 pF each at frequencies up to 400 kHz. It is useful when cable capacitance, remote loading, or separate PCB bus zones exceed the loading that a direct I2C connection can reliably support.
What is the maximum I2C frequency of the PCA9515D?
The PCA9515D supports I2C operation up to 400 kHz. The NXP manufacturer datasheet identifies the device as a BiCMOS repeater for I2C-bus and SMBus systems, with buffered SDA and SCL channels. In practice, the complete system must also meet the 400 kHz timing requirements of the controller, target devices, wiring, pull-up network, and signal integrity margins.
How much bus capacitance can the PCA9515D support?
The PCA9515D can support 400 pF on each of its two buffered bus sections. According to the NXP manufacturer datasheet, the repeater can therefore extend an I2C bus into two 400 pF segments. Each segment must be evaluated independently for its own devices, wiring capacitance, pull-up current, and voltage-level compatibility.
What is the difference between PCA9515D and PCA9515DP?
The PCA9515D and PCA9515DP provide the same 2-channel, 400 kHz I2C repeater function, while their ordering codes distinguish the manufacturer packaging configuration. Both use an 8-pin SOIC outline, so the PCA9515DP can be treated as a drop-in candidate when its reel or tape-and-reel orientation matches the assembly process. Confirm the full ordering suffix and mechanical drawing before substitution.
Can PCA9515D be used in SMBus systems?
Yes, the PCA9515D is explicitly intended for I2C-bus and SMBus systems. Its bidirectional SDA and SCL buffering allows compatible SMBus management traffic to cross a repeater boundary. The system must still satisfy the NXP manufacturer datasheet requirements for supply voltage, bus capacitance, pull-up resistors, enable state, and the 400 kHz maximum operating frequency.
Where can I download the PCA9515D datasheet PDF?
The PCA9515D datasheet is available through the NXP product page, which links to the manufacturer data sheet. The official product-page link is https://www.nxp.com/part/PCA9515D. Use the manufacturer document for the final pin description, recommended application circuit, electrical limits, and soldering information rather than relying only on a distributor listing.
Where can I find the PCA9515D pinout?
The PCA9515D pinout is shown in the NXP manufacturer datasheet for the 8-pin SOIC package. The package is a 3.90 mm-wide surface-mount SOIC with eight pins. Before assigning PCB tracks, use the pin-description table and package drawing in the manufacturer document, including the treatment of enable, supply, ground, and the buffered SDA and SCL connections.
When should I choose the PCA9515D instead of another I2C repeater?
Choose the PCA9515D when the design needs a bidirectional 400 kHz repeater for two I2C or SMBus sections, each operating up to 400 pF, in an 8-pin SOIC footprint. It is a sensible choice for established standard-mode industrial and embedded designs, but it should not be selected when a faster I2C specification, a different package, or a different pin assignment is required.
Is the PCA9515D suitable for extending a remote sensor bus?
The PCA9515D is suitable for a remote standard-mode sensor bus when the cable and attached devices remain within 400 pF per segment and the operating rate does not exceed 400 kHz. The repeater isolates the two sides of the bus and supports bidirectional communication. Cable length alone does not determine compatibility; capacitance, pull-up strength, pull-up voltage, and rise-time margin must also be checked.
Is PCA9515D in stock and what is its lead time?
The NXP product page identifies the PCA9515D as no longer manufactured, so new-production stock and lead time cannot be assumed. Use the Request a Quote form on this page to request current availability, minimum order quantity, and lead time for the exact requested MPN and packaging configuration. Legacy inventory may exist, but its condition and traceability should be reviewed before production use.
What is the price of the PCA9515D?
Current pricing for the obsolete PCA9515D depends on quantity, condition, packaging, and available legacy inventory. Use the Request a Quote form on this page to request the current unit price and volume breaks for the exact MPN. The quote team can distinguish new surplus from used or refurbished stock and confirm whether the offered part is traceable for the intended assembly process.
Where should I buy the PCA9515D?
The recommended sourcing route on this page is the Request a Quote form, where the exact PCA9515D order code, package orientation, quantity, and condition can be specified. Because NXP identifies the device as no longer manufactured, a purchasing decision should include traceability and inspection requirements in addition to availability. Do not substitute a different suffix without checking its mechanical and ordering details.
What is the best drop-in replacement for PCA9515D?
The closest identified drop-in candidate is the NXP PCA9515DP, which retains the 2-channel 400 kHz repeater function in the same 8-pin SOIC outline and differs principally in ordering or packing configuration. It is the only drop-in-class alternative that can be supported from the manufacturer and cross-reference information without changing the PCB footprint. Verify tape orientation and all electrical limits before production use.
Can PCA9515DP replace PCA9515D without changing the PCB?
Yes, the PCA9515DP is an 8-pin SOIC drop-in candidate for the PCA9515D, with the same 2-channel, 400 kHz I2C repeater function and 400 pF-per-segment capability described by NXP. No board change is expected from the package perspective. Check the full ordering code, assembly orientation, supply limits, and manufacturer datasheet before approving the substitution.
What are the key specifications of PCA9515D that engineers should know?
The key PCA9515D specifications are 2 buffered channels, bidirectional SDA and SCL operation, a 400 kHz maximum bus rate, and support for two 400 pF bus segments. The NXP manufacturer datasheet identifies the device as a BiCMOS I2C-bus and SMBus repeater in an 8-pin SOIC package, with an operating temperature range of -40 °C to 85 °C. The NXP product page also states that the device is no longer manufactured.

Data referensi engineering untuk PCA9515D — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the PCA9515D when an existing 8-pin SOIC design uses a standard-mode I2C or SMBus repeater and you need two 400 pF bus sections operating up to 400 kHz. It is particularly appropriate for legacy industrial, embedded, and test systems whose PCB already reflects the PCA9515D footprint and whose I2C pull-up network has been designed for the separate upstream and downstream sections. PCA9515DP is the closest maintained ordering path because it retains the same 8-pin SOIC and 2-channel, 400 kHz repeater function; verify its packaging orientation and current lifecycle status. PCA9515AD,118 is a related 8-pin SOIC candidate, but its detailed electrical limits should be compared with the target design before approval. Neither alternative should be selected merely because it is an I2C buffer: both must preserve the bidirectional SDA and SCL pin functions. Parts with different packages, one-channel buffers, level translators, or differently arranged pins are not drop-in replacements.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini PCA9515DP PCA9515AD,118
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package SOIC-8 SOIC-8 - same SOIC-8 - same
Product Function 2-channel I2C-bus and SMBus repeater 2-channel I2C-bus and SMBus repeater PCA9515-family I2C repeater
Buffered Signals SDA and SCL SDA and SCL SDA and SCL
Signal Direction Bidirectional Bidirectional Bidirectional

Diferensiator Kunci

  • Direct two-segment I2C and SMBus extension (vsPCA9515DP)
  • Bidirectional clock and data buffering in one package (vsPCA9515AD,118)
  • Clear 400 pF-per-segment architecture (vsPCA9515DP)

Catatan Desain

Treat the two repeater sides as separate RC networks. The manufacturer specifies two 400 pF bus segments, but each side still needs its own pull-up calculation based on local bus voltage, total capacitance, sink current, and the required rise time. Do not assume that one pair of pull-up resistors can serve both cable lengths. Also verify the enable state during power-up so that the buffered outputs do not create contention with a connected peripheral.

Route SDA and SCL as a compact, length-matched pair where practical, and keep the two bus sections physically distinct so that the repeater provides meaningful electrical separation. Place the device close to the boundary between the long or heavily loaded section and the local controller section. Use a continuous ground reference, avoid crossing switching-converter nodes, and follow the manufacturer datasheet's recommended supply-decoupling connection with a short ground return.

The PCA9515D is a low-speed interface device, but its supply pins still require a low-impedance reference because SDA and SCL pass through the device. Place the manufacturer-recommended bypass capacitor adjacent to VDD and ground, minimize loop area, and avoid routing the buffered bus directly beneath or beside noisy power-conversion components. When the two bus sections use different logic voltages, confirm that the exact ordering variant supports that condition rather than assuming voltage-level translation.

Verify both rising and falling edges at the slowest supported bus rate with the final cable, connectors, pull-ups, and peripheral loading present. Although the circuit is rated for 400 kHz, long wiring or excessive pull-up resistance can create a slow rising edge even when the controller's clock frequency is compliant. An oscilloscope measurement of SCL rise time, SDA rise time, and bus voltage levels is preferable to relying only on calculated capacitance.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The NXP product page identifies the PCA9515D as no longer manufactured. No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was established from the available manufacturer-page extract.

Data disahkan pada: 2026-11-19 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

PCA9515D datasheet PCA9515D pinout PCA9515D datasheet pdf PCA9515D schematic PCA9515D equivalent PCA9515D replacement PCA9515D cross reference PCA9515D vs PCA9515DP PCA9515D price PCA9515D stock NXP PCA9515D PCA9515D 400kHz I2C repeater PCA9515D SOIC-8 footprint PCA9515D remote sensor bus

Komponen dan Istilah Terkait

NXP Semiconductors PCA9515D PCA9515DP PCA9515AD,118 PCA9515APWR I2C-bus repeater SMBus repeater signal repeater interface IC BiCMOS SDA SCL bidirectional buffer 400 kHz 400 pF SOIC-8 surface mount industrial control remote sensor bus instrumentation embedded systems bus segmentation pull-up resistor
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ