PCA9515D - 2-Channel 400 kHz I2C Bus Repeater | NXP
MPN: PCA9515D ✗ Cuối đờiPCA9515D Tóm tắt
An I2C bus repeater is a signal-conditioning interface used when cable length, bus capacitance, loading, or voltage differences prevent a controller from reliably driving a distant I2C target. In the broader hierarchy, the PCA9515D is an I2C interface repeater within the I2C interface IC category. It allows a master to communicate through one buffered bus segment while isolating that segment from the electrical loading of another segment.
The principal feature is bidirectional buffering of both I2C clock and data lines. According to the NXP manufacturer datasheet, each supported bus arrangement accommodates 400 pF, while the operating frequency reaches 400 kHz. Bidirectional operation permits the controller to address devices on either side of the repeater without changing the I2C protocol. A standard-mode-capable architecture is useful for industrial control, sensor networks, embedded systems, and legacy peripheral expansion where greater speed is unnecessary.
Technically, the PCA9515D is a BiCMOS integrated circuit intended for I2C-bus and SMBus systems. BiCMOS construction combines bipolar and CMOS transistor functions, supporting the interface's bidirectional signal path while maintaining low-power operation. Its two-channel arrangement provides one input-side and one output-side connection for SDA and SCL, creating a controlled separation between bus segments rather than simply adding another capacitive load.
Typical uses include extending a controller connection to remote sensors, isolating a high-load I2C segment, and linking two PCB zones that require separate routing or bus termination. It can also support SMBus-style management buses operating at compatible standard-mode rates. The principal design constraint is ensuring that every side of the repeater remains within its allowed capacitance and that pull-up resistors suit the local voltage and current requirements.
For implementation, place the repeater between the two bus sections and connect the downstream SDA and SCL conductors to the corresponding buffer pins. Provide the supply decoupling recommended by the manufacturer datasheet, and confirm that pull-up resistor values account for the separate cable capacitance of both bus segments. Review the enable behavior and bus contention conditions before using the device in a design that requires hot-plug behavior.
This product page combines the manufacturer lifecycle status, bus-function details, package information, sourcing guidance, and engineering-focused replacement analysis. It also identifies the limits of the available drop-in alternatives, helping designers distinguish electrically equivalent order variants from true pin-compatible replacements before modifying an existing PCB.
Bộ thay thế dễ dàng lắp đặt cho PCA9515D — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
PCA9515DP
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCA9515AD,118
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCA9515D Thông số kỹ thuật
| Product Type | 2-channel I2C-bus and SMBus repeater |
| Supported Bus | I2C-bus and SMBus |
| Channel Count | 2 channels |
| Maximum Bus Frequency | 400 kHz |
| Bus Capacitance per Segment | 400 pF |
| Buffered Signals | SDA and SCL |
| Signal Direction | Bidirectional |
| Logic Technology | BiCMOS |
| Hộp | 8-pin SOIC, 3.90 mm width |
| Kiểu lắp đặt | Surface mount |
| Nhiệt độ hoạt động | -40 °C to 85 °C |
| I2C Maximum Bus Capacitance | 400 pF per bus segment |
Cấu hình chân PCA9515D
| Chân 1 | SCL1 — Bidirectional clock input for the first bus segment |
| Chân 2 | SDA1 — Bidirectional data input for the first bus segment |
| Chân 3 | SCL2 — Bidirectional clock output for the second bus segment |
| Chân 4 | GND — Ground connection |
| Chân 5 | SDA2 — Bidirectional data output for the second bus segment |
| Chân 6 | EN — Repeater enable input |
| Chân 7 | NC — Not connected |
| Chân 8 | VDD — Positive supply connection |
Ứng dụng tiêu biểu
PCA9515D phù hợp cho 6 Áp dụngs: Remote Sensor Bus Extension, Industrial Control Module, SMBus Management Segmentation, PCB Bus-Zone Isolation, Embedded Peripheral Expansion, Instrumentation and Test Equipment.
Remote Sensor Bus Extension
The PCA9515D fits a remote standard-mode sensor bus when the controller and sensors are separated by cable, wiring, or distributed PCB routing. It buffers both SDA and SCL bidirectionally and separates the bus into two sections, each of which may support up to 400 pF according to the NXP manufacturer datasheet. This architecture is useful because a long cable behaves as distributed capacitance and can slow SCL edges enough to violate timing. The repeater must be placed at the boundary between the two segments, with pull-up networks selected for each segment's voltage and capacitance. Its 400 kHz maximum rate supports standard-mode sensors without requiring the faster operating mode of a modern I2C controller.
Được đề xuất
Industrial Control Module
The PCA9515D is useful in an industrial control module where an I2C controller must reach sensors or actuator drivers across separately routed board regions. The device's bidirectional 2-channel structure supports clock and data, while its 400 pF-per-segment rating provides room for distributed wiring and peripheral loading. At the maximum specified 400 kHz, however, pull-up resistance and total capacitance must still be checked for acceptable rise time. Galvanic isolation, level translation, and surge protection remain separate functions and should not be inferred from this repeater. Its 8-pin SOIC package also makes it practical for compact controller boards where a full bus-hub or switch IC would add unnecessary functionality.
Được đề xuất
SMBus Management Segmentation
The PCA9515D can segment an SMBus management connection by buffering the SDA and SCL conductors between a host and downstream management devices. The NXP manufacturer datasheet explicitly identifies SMBus as an intended application and describes the device as a 2-channel BiCMOS repeater. Bidirectional pass-through operation allows the host to address devices on either bus side through one logical bus, while the separation reduces accumulated loading. The host and target devices must use compatible logic levels and the entire path must stay within the 400 kHz maximum frequency. Designers should also review the device's enable and startup behavior when peripherals can be connected, powered, or removed during system operation.
Được đề xuất
PCB Bus-Zone Isolation
The PCA9515D provides a controlled boundary between two PCB bus zones that cannot be treated as one continuous I2C network. Each side can accommodate up to 400 pF, so a board can place a repeater near a zone boundary and route each section according to its own loading. This helps isolate long routed traces, cable connectors, and clustered sensor groups from the controller's direct bus load. The buffered path remains bidirectional, preserving normal command and response traffic without a separate direction-control signal. Layout should keep the upstream and downstream routes physically distinct, use a solid ground reference, and follow the manufacturer's recommended supply bypass arrangement so switching noise does not couple into the buffered signals.
Được đề xuất
Embedded Peripheral Expansion
The PCA9515D can extend an embedded processor's I2C connection to a bank of sensors, EEPROMs, or other low-speed peripherals. The processor continues to use a single logical address space while the repeater separates upstream and downstream loading, allowing each bus section to approach the specified 400 pF limit. At 400 kHz, cable and connector capacitance can materially affect rise time, so the designer should calculate pull-up current for both sections rather than reusing the original bus values unchanged. The device's 8-pin SOIC footprint is convenient for space-constrained control boards, but its no-longer-manufactured status requires lifecycle planning or qualification of a confirmed alternative.
Được đề xuất
Instrumentation and Test Equipment
The PCA9515D is suitable for instrumentation or test equipment that divides low-speed I2C control traffic between a controller card and a remote fixture. Its separate buffered sections help prevent one cable-connected fixture from loading the entire internal bus, while the 400 kHz limit aligns with many sensors, DACs, and display controllers used in measurement systems. For bench equipment, verify ground offsets, connector leakage, and pull-up voltage before enabling communication because the repeater buffers signals but does not provide isolation. Its bidirectional SDA and SCL channels preserve the normal I2C transaction sequence. The 400 pF budget per side should include fixture cables, adapters, protection devices, and every attached peripheral to avoid an unmodeled rise-time penalty.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PCA9515D — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PCA9515DP | PCA9515AD,118 |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | SOIC-8 | SOIC-8 - same | SOIC-8 - same |
| Product Function | 2-channel I2C-bus and SMBus repeater | 2-channel I2C-bus and SMBus repeater | PCA9515-family I2C repeater |
| Buffered Signals | SDA and SCL | SDA and SCL | SDA and SCL |
| Signal Direction | Bidirectional | Bidirectional | Bidirectional |
Bảo phân biệt quan trọng
- Direct two-segment I2C and SMBus extension (vsPCA9515DP)
- Bidirectional clock and data buffering in one package (vsPCA9515AD,118)
- Clear 400 pF-per-segment architecture (vsPCA9515DP)
Ghi chú thiết kế
Treat the two repeater sides as separate RC networks. The manufacturer specifies two 400 pF bus segments, but each side still needs its own pull-up calculation based on local bus voltage, total capacitance, sink current, and the required rise time. Do not assume that one pair of pull-up resistors can serve both cable lengths. Also verify the enable state during power-up so that the buffered outputs do not create contention with a connected peripheral.
Route SDA and SCL as a compact, length-matched pair where practical, and keep the two bus sections physically distinct so that the repeater provides meaningful electrical separation. Place the device close to the boundary between the long or heavily loaded section and the local controller section. Use a continuous ground reference, avoid crossing switching-converter nodes, and follow the manufacturer datasheet's recommended supply-decoupling connection with a short ground return.
The PCA9515D is a low-speed interface device, but its supply pins still require a low-impedance reference because SDA and SCL pass through the device. Place the manufacturer-recommended bypass capacitor adjacent to VDD and ground, minimize loop area, and avoid routing the buffered bus directly beneath or beside noisy power-conversion components. When the two bus sections use different logic voltages, confirm that the exact ordering variant supports that condition rather than assuming voltage-level translation.
Verify both rising and falling edges at the slowest supported bus rate with the final cable, connectors, pull-ups, and peripheral loading present. Although the circuit is rated for 400 kHz, long wiring or excessive pull-up resistance can create a slow rising edge even when the controller's clock frequency is compliant. An oscilloscope measurement of SCL rise time, SDA rise time, and bus voltage levels is preferable to relying only on calculated capacitance.
Thông tin tuân thủ
The NXP product page identifies the PCA9515D as no longer manufactured. No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was established from the available manufacturer-page extract.