Texas Instruments

PCA9517DGKR - 2-Bit 400kHz I2C Level Translator | Texas Instruments

MPN: PCA9517DGKR ✓ Aktif
0.9 V to 5.5 V Vdss 8-pin VSSOP Package 400 kHz Speed
MOQ: 1 |

PCA9517DGKR Ringkasan

The Texas Instruments PCA9517DGKR is a 2-bit level-translating I2C bus buffer/repeater designed for bidirectional voltage-level translation between low-voltage and higher-voltage logic domains. It supports I2C and SMBus systems operating up to 400 kHz, uses two independently supplied voltage rails, and is housed in an 8-pin VSSOP package. The device is intended for systems in which the I2C bus must cross between different supply-voltage domains while retaining bidirectional communication.

An I2C level-translating buffer, also called an I2C bus repeater or bidirectional level translator, is an interface IC that separates two I2C bus segments connected to separate voltage supplies. It allows a low-voltage controller to communicate with a higher-voltage peripheral without violating the input thresholds of either device. In the broader hierarchy, the PCA9517DGKR belongs to the voltage-translator and interface-controller class within interface ICs, rather than acting as a standalone microcomputer or power converter.

The PCA9517 family provides two bidirectional channels, allowing the repeater to extend or isolate an I2C or SMBus connection. Its separate low-side and high-side supply pins permit the two sides of the bus to operate at different logic levels. The device is specified for a maximum bus frequency of 400 kHz, making it appropriate for standard-speed I2C systems and SMBus-compatible equipment. Its level-translation function helps reduce voltage-threshold, noise-immunity, and capacitive-loading problems that occur when devices with incompatible supply voltages share the same bus.

The device is identified as a BiCMOS integrated circuit intended for I2C bus and SMBus systems. The verified manufacturer product page describes it as a 2-bit level-translating 400-kHz I2C/SMBus buffer/repeater. Because the sides are independently powered, the translator can accommodate logic-domain differences that are commonly encountered between low-voltage sensors, embedded processors, EEPROMs, and higher-voltage interface peripherals. The translator does not change the serial data format and does not increase the protocol's maximum clock rate beyond its specified 400-kHz capability.

Typical uses include voltage isolation between a low-voltage microcontroller and a higher-voltage sensor bus, extending an I2C connection into a separate voltage domain, and interfacing peripheral groups that require different supply rails. The device can also be used in industrial equipment, portable electronics, instrumentation, and communication modules where a robust I2C bus segmentation strategy is preferred over directly tying incompatible logic levels together. System designers should account for bus capacitance, pull-up resistor placement, supply sequencing, and the operating limits of both connected bus domains.

PCA9517DGKR is packaged in the compact 8-pin VSSOP form identified by the TI ordering code DGKR. The DGK package is intended for surface-mount assembly and supports compact PCB layouts. The key design tradeoff is that level translation adds a buffer and separate supply domains, so the design must preserve correct pull-up placement and ensure that both supplies remain within the limits specified for the device. The TI comparison materials identify TCA9517 as a related device with application and datasheet guidance that should be reviewed when selecting a replacement or new-design alternative.

This page organizes the manufacturer product information, package identity, source links, technical use cases, and drop-in replacement findings for PCA9517DGKR. It emphasizes verified interface characteristics rather than treating every similarly packaged translator as automatically interchangeable, because enable behavior, electrical limits, pin functions, and bus-direction assumptions can differ between devices.

Alternatif penggantian untuk PCA9517DGKR — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian PCA9517DGKR (sama faktor bentuk dan footprint) — berbeda di dalam Package, Function, Number of Channels, Powered-Off High Impedance.

Texas Instruments
Package: 8-VSSOP (DGK), 3.00 mm width
Function: Level-translating I2C/SMBus buffer, repeater
Powered-Off High Impedance: Yes (I2C pins high-Z when supply off)
Bandingkan dengan PCA9517DGKR →
Texas Instruments
Package: VSSOP (DGK), 8 pins
Function: Level-translating I2C/SMBus buffer/repeater
Number of Channels: 2 (1 bidirectional circuit)
Bandingkan dengan PCA9517DGKR →

TCA9517DGKR

✅ Drop-In
Texas Instruments
📦 8-VSSOP (DGK)
Level-translating I2C/SMBus buffer, repeater · 2 (bidirectional SDA, SCL) · 1 · 400 kHz (Fast-mode I2C) · 0.9 V to 5.5 V · 2.7 V to 5.5 V · VCCA <= VCCB · Yes (EN)

Kontak untuk harga

Lihat Datasheet →

PCA9517DGKR Spesifikasi

Product Type 2-bit level-translating I2C bus buffer/repeater
Supported Bus I2C and SMBus
Maximum Bus Frequency 400 kHz
Number of Channels 2 channels
Signal Direction Bidirectional
Low-Side Supply Voltage Range 0.9 V to 5.5 V
High-Side Supply Voltage Range 2.7 V to 5.5 V
Process Technology BiCMOS
Paket 8-pin VSSOP
Package Designation DGKR
Tipe Mounting Surface mount
Rentang Suhu Kerja -40 °C to +85 °C

PCA9517DGKR dgkr Diamant Konfigurasi Panduan

Konfigurasi pin untuk PCA9517DGKR (dgkr pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai dgkr untuk PCA9517DGKR

Tidak ada data diatribut pin yang tersedia untuk PCA9517DGKR.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

PCA9517DGKR cocok untuk 6 aplikasis: Low-Voltage MCU to Higher-Voltage Sensor Bus, Portable Instrument Bus Segmentation, Industrial Control Module Bus Isolation, Communication and Network Peripheral Bus, Data Acquisition Front-End, Embedded EEPROM and Peripheral Expansion.

🧩

Low-Voltage MCU to Higher-Voltage Sensor Bus

The PCA9517DGKR fits when a low-voltage microcontroller must communicate with a sensor placed in a higher I2C logic domain. Its two bidirectional channels allow SDA and SCL to cross the voltage boundary, while the 0.9 V to 5.5 V low-side and 2.7 V to 5.5 V high-side supplies support common embedded power rails. Pull-ups should reference the supply on each side rather than being shared across the translator. The 400-kHz limit is suitable for standard-speed sensors, but rise time, propagation delay, and the slowest attached device determine the achievable bus rate.

📱

Portable Instrument Bus Segmentation

The PCA9517DGKR can segment an I2C bus in a portable measurement instrument where the controller and analog or sensor subsystem operate from different voltage rails. Bidirectional translation preserves two-wire communication without requiring separate unidirectional level-shift paths. The compact 8-VSSOP package helps conserve board area in space-constrained products. Because translation introduces propagation delay and the device is rated to 400 kHz, designers should use separate pull-up networks and verify the complete timing budget rather than assuming full-speed operation for every peripheral.

🏭

Industrial Control Module Bus Isolation

The PCA9517DGKR is applicable in industrial control modules that connect a low-voltage controller to peripherals on a separate higher-voltage logic domain. Its independently supplied sides reduce the need for a common-ground-only I2C arrangement, while two bidirectional channels carry both clock and data. The 400-kHz operating ceiling suits standard-speed industrial peripheral buses. Layout should keep the translator and its bus traces away from high-current switching paths, and pull-up placement must follow each side's reference rail to maintain valid logic levels.

🌐

Communication and Network Peripheral Bus

The PCA9517DGKR can connect an I2C management bus between a network or communications module and a peripheral domain using a different supply voltage. Two bidirectional channels support both SCL and SDA without changing the I2C protocol. Its maximum 400-kHz frequency suits management and configuration buses rather than high-speed data paths. System designers should account for clock stretching, bus capacitance, and the accumulated delay introduced by the translator. Pull-ups must be placed independently on each side, with their voltage and resistance selected for the devices on that segment.

📺

Data Acquisition Front-End

The PCA9517DGKR is useful when an ADC or data-acquisition subsystem uses a higher I2C voltage than the processing controller. The buffered level translation isolates the logic thresholds while retaining a standard two-wire interface for configuration and calibration. The two translated channels support clock and data, and the 400-kHz ceiling is commonly adequate for control traffic rather than high-rate sample streaming. Validate propagation delay, pull-up rise time, and device-specific I2C timing, especially when the converter uses clock stretching or operates with long bus traces.

🔧

Embedded EEPROM and Peripheral Expansion

The PCA9517DGKR can connect an embedded controller to an EEPROM or other expansion peripheral located on a different voltage domain. Bidirectional translation handles both write commands and returned data without separate direction-control logic. Its low-side supply can extend down to 0.9 V, making it relevant to modern microcontroller rails, while the high-side range supports conventional peripheral supplies. The 400-kHz limit is adequate for configuration and parameter storage. Use correctly sized pull-ups on both bus segments and verify that the peripheral's minimum high-level voltage is met at every operating condition.

What is the PCA9517DGKR used for?
The PCA9517DGKR is a 2-bit bidirectional level-translating I2C bus buffer/repeater used to connect I2C or SMBus segments operating from different logic-voltage domains. According to the Texas Instruments PCA9517 product page, it supports bus frequencies up to 400 kHz and uses separate voltage rails for the two sides of the bus. The PCA9517DGKR is packaged in an 8-pin VSSOP and is intended for systems where directly connecting incompatible logic levels could cause incorrect data thresholds, excessive noise, or unreliable bus communication.
What is the maximum I2C frequency of the PCA9517DGKR?
The PCA9517DGKR supports I2C and SMBus operation up to 400 kHz. The Texas Instruments PCA9517 product page identifies the device as a 2-bit, 400-kHz level-translating buffer/repeater, while distributor product information describes the exact DGKR ordering code as an 8-VSSOP device. The 400-kHz rating makes it suitable for standard-speed I2C communication, but the complete system must still satisfy rise-time, pull-up resistor, capacitance, and timing requirements for the attached bus devices.
How many I2C channels does the PCA9517DGKR provide?
The PCA9517DGKR provides two bidirectional I2C channels. Each channel can support communication across the translator boundary rather than operating as a one-way unidirectional level shifter. Texas Instruments describes the PCA9517 family as a 2-bit level-translating 400-kHz I2C/SMBus buffer/repeater. Because the device has separate low-side and high-side supplies, the two logical bus domains can use different voltage levels while retaining standard SDA and SCL bus signaling.
What are the PCA9517DGKR supply-voltage ranges?
The PCA9517DGKR operates with a low-side supply from 0.9 V to 5.5 V and a high-side supply from 2.7 V to 5.5 V. These ranges describe the two independently supplied sides of the bidirectional I2C translator. The low-side range permits compatibility with modern low-voltage digital systems, while the high-side range supports conventional higher-voltage logic domains. The attached I2C devices and pull-up resistors must use voltages appropriate for their respective bus segments.
Can the TCA9517DGKR replace the PCA9517DGKR?
The TCA9517DGKR is a pin-compatible candidate to evaluate for a PCA9517DGKR replacement because both are listed as 8-VSSOP, two-channel bidirectional translators. However, Texas Instruments notes that the TCA9517 addresses application limitations specified for the PCA9517 datasheet, and a direct substitution should account for enable behavior and device-specific operating conditions. The PCA9517DGKR remains the preferred choice when its original electrical and functional requirements are unchanged.
Where can I download the PCA9517DGKR datasheet?
The PCA9517DGKR datasheet can be obtained from the official Texas Instruments PCA9517 product page at https://www.ti.com/product/PCA9517, which links to the device documentation. The exact ordering code PCA9517DGKR identifies the device in the 8-pin VSSOP DGKR package. When creating a PCB or servicing an existing assembly, use the manufacturer datasheet's pin-description table, electrical characteristics, application information, and errata rather than relying on a generic I2C translator pinout.
Where can I find the PCA9517DGKR pinout?
The PCA9517DGKR pinout is documented in the Texas Instruments PCA9517 datasheet linked from https://www.ti.com/product/PCA9517. The DGKR ordering code denotes the 8-pin VSSOP package, but a package code alone does not establish every signal name. Use the datasheet's pin-configuration diagram and connection table to identify the two supply domains, ground pins, and the SDA/SCL channel pins before laying out or probing the board.
Is the PCA9517DGKR suitable for voltage isolation between an MCU and sensor?
Yes, the PCA9517DGKR is suitable when an MCU and sensor use different I2C logic-voltage domains and the bus remains within the translator's supply limits. Its two bidirectional channels and independently separated supplies allow the low-voltage and high-voltage sides to be referenced to different rails. The design must include correctly placed pull-ups on each side, maintain compatible device thresholds, and observe the PCA9517 operating and supply constraints. The 400-kHz maximum also needs to match the slower device on the bus.
What is the difference between PCA9517DGKR and PCA9517DR?
The principal difference identified by the available product information is the package format: PCA9517DGKR is the 8-VSSOP DGKR version, whereas PCA9517DR is listed in an 8-pin SOIC package. Both are associated with the same PCA9517 level-translating I2C repeater family and the same 400-kHz bus class. Because SOIC and VSSOP have different land patterns and dimensions, PCA9517DR is not a physical drop-in replacement for PCA9517DGKR even if its core interface function is similar.
When should I choose the PCA9517DGKR over a TCA9517DGKR?
Choose the PCA9517DGKR when maintaining an existing PCA9517-based design is more important than adopting the application-limit corrections associated with TCA9517. The two devices are both identified as 8-VSSOP, two-channel bidirectional translators, which makes the TCA9517DGKR a candidate for evaluation, but their documented application limitations are not identical. For new designs, compare enable behavior, operating limits, timing, and the specific bus configuration in the manufacturer documentation before selecting either device.
Where can I buy PCA9517DGKR and what is the current lead time?
Use the Request a Quote form on this page to ask about PCA9517DGKR availability, current lead time, minimum order quantity, and shipment options. The verified distributor results include the exact PCA9517DGKR ordering code, but their snippets do not provide a complete quantity-break price table or a guaranteed current stock quantity. The manufacturer product page remains the authoritative source for ordering options and lifecycle information, while the quote form provides a direct response for commercial requirements.
How do I design the pull-up resistors around PCA9517DGKR?
Place an I2C pull-up on each side of the translator so that each bus segment is referenced to its own supply domain. The low-side pull-up should use the low-voltage rail, while the high-side pull-up should use the high-voltage rail. Select resistance from the bus capacitance, rise-time requirement, sink-current limit, and logic VOL rather than copying one value across both domains. Verify the complete network against the 400-kHz timing limit and the pull-up current limits of every attached device.
Does the PCA9517DGKR add propagation delay to an I2C bus?
Yes, the level-translating buffer introduces propagation delay through each translated channel, so total system timing must include the translator's contribution. The PCA9517 is specified for I2C and SMBus operation up to 400 kHz, but the usable timing margin depends on bus capacitance, pull-up resistance, clock stretching, device delays, and the round-trip path through the bidirectional SDA or SCL channel. Validate timing with the slowest attached device and the highest intended bus capacitance.
What are the key specifications of PCA9517DGKR that engineers should know?
The PCA9517DGKR is a 2-bit bidirectional level translator for I2C and SMBus, rated for operation up to 400 kHz. Its low-side supply range is 0.9 V to 5.5 V, while its high-side supply range is 2.7 V to 5.5 V. The exact device is packaged in an 8-pin VSSOP with the DGKR ordering code. Texas Instruments identifies the PCA9517 family as a BiCMOS interface IC, with separate supply domains for translating between incompatible logic voltages.
What can replace PCA9517DGKR on an existing PCB?
The strongest identified replacement candidate is the TCA9517DGKR because it uses the same 8-VSSOP format and provides two bidirectional translation channels. It should still be checked against the PCA9517 datasheet's application limitations and the original board's enable and supply arrangements. PCA9517DR is functionally related but uses an 8-pin SOIC package, so it requires a footprint change and is not a drop-in PCB replacement. No additional drop-in alternatives could be established from the available results.
Is the PCA9517DGKR compliant with RoHS and REACH?
The RoHS and REACH status of the exact PCA9517DGKR ordering code is not stated in the available manufacturer snippets, so compliance should be confirmed from the current Texas Instruments product-page compliance information or supporting declarations. Do not infer compliance solely from the PCA9517 family name because environmental declarations can vary by ordering code, package, and revision. For a regulated production release, obtain the applicable manufacturer declaration and archive it with the procurement and quality records.

Data referensi engineering untuk PCA9517DGKR — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose PCA9517DGKR when an existing board needs a 2-bit I2C/SMBus translator with 400-kHz operation, 0.9 V to 5.5 V low-side capability, and a 2.7 V to 5.5 V high-side supply. It is particularly suitable when the two bus domains use different rails and each side needs its own pull-up network. TCA9517DGKR is the closest identified 8-VSSOP replacement candidate and may resolve application limitations described for PCA9517, but its enable behavior and operating conditions must be checked before substitution. PCA9517DR is not a physical drop-in choice because it uses SOIC rather than the target VSSOP footprint. For new designs, compare both TI devices against the exact bus topology, voltage levels, timing budget, and lifecycle objectives. Use PCA9517DGKR when preserving the established PCA9517 behavior is the primary requirement.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini TCA9517DGKR
Package 8-VSSOP (DGKR) 8-VSSOP (DGK)
Brand Texas Instruments Texas Instruments
Product Type Level-translating I2C bus repeater Bidirectional voltage level translator
Channel Count 2 channels 2 channels
Signal Direction Bidirectional Bidirectional

Diferensiator Kunci

  • Two independent supply domains support direct I2C voltage translation (vsTCA9517DGKR)
  • Standard-speed I2C and SMBus coverage (vsTCA9517DGKR)
  • BiCMOS implementation for bidirectional interface operation (vsTCA9517DGKR)

Catatan Desain

Route each I2C segment as a continuous path through the PCA9517DGKR and place its pull-up resistor on the corresponding side of the translator. The low-side pull-up should reference VCCA and the high-side pull-up should reference VCCB. Keep the device and bus traces away from switching nodes and high-current return paths. Because bidirectional translators can oscillate if the bus is held at an intermediate voltage during startup, verify that the system’s enable sequence or pull-up arrangement does not leave both sides floating.

Select pull-up resistance from the target rise time, total bus capacitance, and sink-current capability rather than using a single value for both sides. Include the translator’s propagation delay, the slowest attached device, and any clock stretching when checking whether the design can operate at the intended I2C rate. Although the PCA9517DGKR supports 400 kHz, the practical maximum is limited by the slowest segment, so validate the assembled board with realistic capacitance and loading.

Decouple VCCA and VCCB independently with short, low-impedance connections, and observe the decoupling and supply-ramp requirements in the manufacturer datasheet. A common supply is not required because the translator is specifically intended to bridge separately referenced logic domains. Confirm that each supply remains within its 0.9 V to 5.5 V low-side or 2.7 V to 5.5 V high-side range during startup, shutdown, and fault conditions.

Do not treat PCA9517DR as a footprint-compatible substitute for PCA9517DGKR: the former is listed in 8-pin SOIC while the target uses the DGKR VSSOP package. Likewise, confirm every signal name and supply connection against the datasheet rather than inferring the pinout from another two-channel translator. When evaluating TCA9517DGKR as a replacement, review the documented application limitations and the original board's enable behavior to avoid introducing a functional difference into a drop-in exchange.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The available manufacturer and distributor snippets do not state the environmental-compliance status of the exact ordering code. The interface IC is not presented as an automotive-qualified AEC-Q100 device.

Pencarian Terkait

PCA9517DGKR datasheet PCA9517DGKR pinout PCA9517DGKR datasheet pdf PCA9517DGKR equivalent PCA9517DGKR replacement PCA9517DGKR vs TCA9517DGKR Texas Instruments PCA9517DGKR PCA9517DGKR 400kHz I2C PCA9517DGKR VSSOP pinout PCA9517DGKR application circuit PCA9517DGKR price PCA9517DGKR stock PCA9517 level translating bus repeater PCA9517 VSSOP footprint

Komponen dan Istilah Terkait

Texas Instruments PCA9517DGKR PCA9517 TCA9517DGKR PCA9517DR I2C bus SMBus level-translating buffer I2C bus repeater bidirectional level translator interface IC voltage translator semiconductor BiCMOS VSSOP-8 DGKR package surface-mount package 400 kHz I2C 0.9 V low-side supply 2.7 V high-side supply bidirectional SDA bidirectional SCL I2C pull-up resistor signal integrity industrial electronics portable electronics
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ