PCA9517DGKR - 2-Bit 400kHz I2C Level Translator | Texas Instruments
料号: PCA9517DGKR ✓ 量产中PCA9517DGKR 概述
An I2C level-translating buffer, also called an I2C bus repeater or bidirectional level translator, is an interface IC that separates two I2C bus segments connected to separate voltage supplies. It allows a low-voltage controller to communicate with a higher-voltage peripheral without violating the input thresholds of either device. In the broader hierarchy, the PCA9517DGKR belongs to the voltage-translator and interface-controller class within interface ICs, rather than acting as a standalone microcomputer or power converter.
The PCA9517 family provides two bidirectional channels, allowing the repeater to extend or isolate an I2C or SMBus connection. Its separate low-side and high-side supply pins permit the two sides of the bus to operate at different logic levels. The device is specified for a maximum bus frequency of 400 kHz, making it appropriate for standard-speed I2C systems and SMBus-compatible equipment. Its level-translation function helps reduce voltage-threshold, noise-immunity, and capacitive-loading problems that occur when devices with incompatible supply voltages share the same bus.
The device is identified as a BiCMOS integrated circuit intended for I2C bus and SMBus systems. The verified manufacturer product page describes it as a 2-bit level-translating 400-kHz I2C/SMBus buffer/repeater. Because the sides are independently powered, the translator can accommodate logic-domain differences that are commonly encountered between low-voltage sensors, embedded processors, EEPROMs, and higher-voltage interface peripherals. The translator does not change the serial data format and does not increase the protocol's maximum clock rate beyond its specified 400-kHz capability.
Typical uses include voltage isolation between a low-voltage microcontroller and a higher-voltage sensor bus, extending an I2C connection into a separate voltage domain, and interfacing peripheral groups that require different supply rails. The device can also be used in industrial equipment, portable electronics, instrumentation, and communication modules where a robust I2C bus segmentation strategy is preferred over directly tying incompatible logic levels together. System designers should account for bus capacitance, pull-up resistor placement, supply sequencing, and the operating limits of both connected bus domains.
PCA9517DGKR is packaged in the compact 8-pin VSSOP form identified by the TI ordering code DGKR. The DGK package is intended for surface-mount assembly and supports compact PCB layouts. The key design tradeoff is that level translation adds a buffer and separate supply domains, so the design must preserve correct pull-up placement and ensure that both supplies remain within the limits specified for the device. The TI comparison materials identify TCA9517 as a related device with application and datasheet guidance that should be reviewed when selecting a replacement or new-design alternative.
This page organizes the manufacturer product information, package identity, source links, technical use cases, and drop-in replacement findings for PCA9517DGKR. It emphasizes verified interface characteristics rather than treating every similarly packaged translator as automatically interchangeable, because enable behavior, electrical limits, pin functions, and bus-direction assumptions can differ between devices.
直接替换替代料: PCA9517DGKR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: PCA9517DGKR (相同外形与封装尺寸) ——差异在于 Package, Function, Number of Channels, Powered-Off High Impedance.
TCA9517DGKR
✅ 直接替换联系询价
查看数据手册 →PCA9517DGKR 规格参数
| Product Type | 2-bit level-translating I2C bus buffer/repeater |
| Supported Bus | I2C and SMBus |
| Maximum Bus Frequency | 400 kHz |
| Number of Channels | 2 channels |
| Signal Direction | Bidirectional |
| Low-Side Supply Voltage Range | 0.9 V to 5.5 V |
| High-Side Supply Voltage Range | 2.7 V to 5.5 V |
| Process Technology | BiCMOS |
| 封装 | 8-pin VSSOP |
| Package Designation | DGKR |
| 安装类型 | Surface mount |
| 工作温度范围 | -40 °C to +85 °C |
PCA9517DGKR dgkr 引脚配置指南
PCA9517DGKR(dgkr 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: PCA9517DGKR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCA9517DGKR 适用于 6 应用s: Low-Voltage MCU to Higher-Voltage Sensor Bus, Portable Instrument Bus Segmentation, Industrial Control Module Bus Isolation, Communication and Network Peripheral Bus, Data Acquisition Front-End, Embedded EEPROM and Peripheral Expansion.
Low-Voltage MCU to Higher-Voltage Sensor Bus
The PCA9517DGKR fits when a low-voltage microcontroller must communicate with a sensor placed in a higher I2C logic domain. Its two bidirectional channels allow SDA and SCL to cross the voltage boundary, while the 0.9 V to 5.5 V low-side and 2.7 V to 5.5 V high-side supplies support common embedded power rails. Pull-ups should reference the supply on each side rather than being shared across the translator. The 400-kHz limit is suitable for standard-speed sensors, but rise time, propagation delay, and the slowest attached device determine the achievable bus rate.
推荐
Portable Instrument Bus Segmentation
The PCA9517DGKR can segment an I2C bus in a portable measurement instrument where the controller and analog or sensor subsystem operate from different voltage rails. Bidirectional translation preserves two-wire communication without requiring separate unidirectional level-shift paths. The compact 8-VSSOP package helps conserve board area in space-constrained products. Because translation introduces propagation delay and the device is rated to 400 kHz, designers should use separate pull-up networks and verify the complete timing budget rather than assuming full-speed operation for every peripheral.
推荐
Industrial Control Module Bus Isolation
The PCA9517DGKR is applicable in industrial control modules that connect a low-voltage controller to peripherals on a separate higher-voltage logic domain. Its independently supplied sides reduce the need for a common-ground-only I2C arrangement, while two bidirectional channels carry both clock and data. The 400-kHz operating ceiling suits standard-speed industrial peripheral buses. Layout should keep the translator and its bus traces away from high-current switching paths, and pull-up placement must follow each side's reference rail to maintain valid logic levels.
推荐
Communication and Network Peripheral Bus
The PCA9517DGKR can connect an I2C management bus between a network or communications module and a peripheral domain using a different supply voltage. Two bidirectional channels support both SCL and SDA without changing the I2C protocol. Its maximum 400-kHz frequency suits management and configuration buses rather than high-speed data paths. System designers should account for clock stretching, bus capacitance, and the accumulated delay introduced by the translator. Pull-ups must be placed independently on each side, with their voltage and resistance selected for the devices on that segment.
推荐
Data Acquisition Front-End
The PCA9517DGKR is useful when an ADC or data-acquisition subsystem uses a higher I2C voltage than the processing controller. The buffered level translation isolates the logic thresholds while retaining a standard two-wire interface for configuration and calibration. The two translated channels support clock and data, and the 400-kHz ceiling is commonly adequate for control traffic rather than high-rate sample streaming. Validate propagation delay, pull-up rise time, and device-specific I2C timing, especially when the converter uses clock stretching or operates with long bus traces.
推荐
Embedded EEPROM and Peripheral Expansion
The PCA9517DGKR can connect an embedded controller to an EEPROM or other expansion peripheral located on a different voltage domain. Bidirectional translation handles both write commands and returned data without separate direction-control logic. Its low-side supply can extend down to 0.9 V, making it relevant to modern microcontroller rails, while the high-side range supports conventional peripheral supplies. The 400-kHz limit is adequate for configuration and parameter storage. Use correctly sized pull-ups on both bus segments and verify that the peripheral's minimum high-level voltage is met at every operating condition.
推荐
推荐产品汇总
工程参考数据: PCA9517DGKR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TCA9517DGKR |
|---|---|---|
| Package | 8-VSSOP (DGKR) | 8-VSSOP (DGK) |
| Brand | Texas Instruments | Texas Instruments |
| Product Type | Level-translating I2C bus repeater | Bidirectional voltage level translator |
| Channel Count | 2 channels | 2 channels |
| Signal Direction | Bidirectional | Bidirectional |
关键差异点
- Two independent supply domains support direct I2C voltage translation (对比 TCA9517DGKR)
- Standard-speed I2C and SMBus coverage (对比 TCA9517DGKR)
- BiCMOS implementation for bidirectional interface operation (对比 TCA9517DGKR)
设计说明
Route each I2C segment as a continuous path through the PCA9517DGKR and place its pull-up resistor on the corresponding side of the translator. The low-side pull-up should reference VCCA and the high-side pull-up should reference VCCB. Keep the device and bus traces away from switching nodes and high-current return paths. Because bidirectional translators can oscillate if the bus is held at an intermediate voltage during startup, verify that the system’s enable sequence or pull-up arrangement does not leave both sides floating.
Select pull-up resistance from the target rise time, total bus capacitance, and sink-current capability rather than using a single value for both sides. Include the translator’s propagation delay, the slowest attached device, and any clock stretching when checking whether the design can operate at the intended I2C rate. Although the PCA9517DGKR supports 400 kHz, the practical maximum is limited by the slowest segment, so validate the assembled board with realistic capacitance and loading.
Decouple VCCA and VCCB independently with short, low-impedance connections, and observe the decoupling and supply-ramp requirements in the manufacturer datasheet. A common supply is not required because the translator is specifically intended to bridge separately referenced logic domains. Confirm that each supply remains within its 0.9 V to 5.5 V low-side or 2.7 V to 5.5 V high-side range during startup, shutdown, and fault conditions.
Do not treat PCA9517DR as a footprint-compatible substitute for PCA9517DGKR: the former is listed in 8-pin SOIC while the target uses the DGKR VSSOP package. Likewise, confirm every signal name and supply connection against the datasheet rather than inferring the pinout from another two-channel translator. When evaluating TCA9517DGKR as a replacement, review the documented application limitations and the original board's enable behavior to avoid introducing a functional difference into a drop-in exchange.
合规信息
The available manufacturer and distributor snippets do not state the environmental-compliance status of the exact ordering code. The interface IC is not presented as an automotive-qualified AEC-Q100 device.