PCA9536DRG4 - 4-Bit I2C I/O Expander | Texas Instruments
MPN: PCA9536DRG4 ✓ AktifPCA9536DRG4 Ringkasan
An I/O expander is a peripheral integrated circuit that increases the number of general-purpose digital inputs and outputs available to a host microcontroller or processor. The host communicates with the PCA9536DRG4 through the two-wire I2C bus, using serial clock and serial data lines. The device supports both I2C and SMBus-style access, making it suitable for industrial controllers, embedded modules, and compact control systems that need additional GPIOs without enlarging the host device.
The principal specifications are a 4-bit I/O count, a 2.3 V to 5.5 V operating range, bus operation up to 400 kHz, and an 8-pin SOIC package. Configuration registers allow each of the four ports to be selected independently as an input or output. Separate input-port, output-port, and active-high or active-low polarity-inversion registers provide software-controlled behavior for connected sensors, interrupt signals, indicators, and control inputs.
The architecture places a small serial interface beside four independently configurable port pins. Because the port registers are remotely accessible over I2C, the host can read input states, update output levels, and invert input polarity without dedicating a host GPIO pin to every external signal. The active-low interrupt output provides a compact mechanism for notifying the host when a programmed input condition occurs, although the exact implemented behavior should be confirmed in the manufacturer datasheet and the host firmware.
Typical uses include expanding a microcontroller in a programmable logic controller, adding digital control lines to an embedded instrument, reading discrete industrial inputs, driving indicator or enable signals, and providing a small remote I/O node connected through an I2C bus. The 2.3 V minimum supply supports low-voltage embedded systems, while the 5.5 V maximum accommodates conventional 5 V logic environments when the host and bus levels are compatible.
PCB design should preserve the 8-SOIC footprint and place pull-up resistors for SDA and SCL according to the bus voltage, capacitance, and required rise time. Confirm the address arrangement, reset behavior, input default state, and interrupt polarity in the manufacturer datasheet before firmware and schematic sign-off. The fixed-address nature of this device also matters when multiple identical expanders share one bus.
This page consolidates the exact package and bus information with practical replacement guidance, design cautions, and application-focused engineering context. It also distinguishes the PCA9536DRG4 from related ordering variants so engineers can assess board-fit and register-level compatibility before approving a substitution.
Alternatif penggantian untuk PCA9536DRG4 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PCA9536DRG4 (sama faktor bentuk dan footprint) — berbeda di dalam Configuration Registers, Package, Product Type.
PCA9536DR
✅ Drop-InKontak untuk harga
Lihat Datasheet →PCA9536DG4
✅ Drop-InKontak untuk harga
Lihat Datasheet →PCA9536D
✅ Drop-InKontak untuk harga
Lihat Datasheet →PCA9536DRG4 Spesifikasi
| Product Type | 4-bit I2C and SMBus remote I/O expander |
| Number of I/O Ports | 4 bits |
| Supply Voltage Range | 2.3 V to 5.5 V |
| Maximum I2C Bus Frequency | 400 kHz |
| Tipe Antarmuka | I2C and SMBus |
| Configuration Registers | 4 configuration bits, one for each I/O |
| Input Port Register | 1 register |
| Output Port Register | 1 register |
| Polarity Inversion Register | 1 register with active-high or active-low selection |
| Paket | 8-pin SOIC, 0.154 inch (3.90 mm) width |
| Tipe Mounting | Surface mount |
Konfigurasi Pin PCA9536DRG4
| Pin produk 1 | INT — Interrupt output |
| Pin produk 2 | P3 — Configurable I/O port 3 |
| Pin produk 3 | P2 — Configurable I/O port 2 |
| Pin produk 4 | P1 — Configurable I/O port 1 |
| Pin produk 5 | P0 — Configurable I/O port 0 |
| Pin produk 6 | GND — Ground |
| Pin produk 7 | SCL — Serial clock |
| Pin produk 8 | SDA — Serial data |
Aplikasi Umum
PCA9536DRG4 cocok untuk 6 aplikasis: Industrial PLC Discrete I/O Expansion, Microcontroller Button and Indicator Expansion, Embedded Sensor and Discrete Input Interface, Programmable Relay and Control Output, Remote Instrumentation I/O Node, Battery-Powered Sensor Node.
Industrial PLC Discrete I/O Expansion
The PCA9536DRG4 fits a compact PLC or industrial controller that needs additional discrete inputs and outputs without enlarging the host processor package. Its four bits can be configured independently as inputs or outputs, while the 2.3 V to 5.5 V operating range accommodates common control-system supply levels. Connecting the device through SDA and SCL preserves the two-wire bus architecture, and the configuration registers allow software to adapt each port as field wiring changes. Because the interface operates up to 400 kHz, several compatible devices can share a suitably designed bus. Designers must confirm the fixed address against other peripherals and select pull-ups for the actual bus voltage and capacitance.
Microcontroller Button and Indicator Expansion
The PCA9536DRG4 is useful when a microcontroller has insufficient GPIOs for front-panel buttons, status LEDs, mode controls, or discrete enable signals. Its 4-bit port can mix input and output functions, and separate input, output, and polarity-inversion registers simplify software handling of active-low buttons or active-high indicators. The 8-SOIC package preserves PCB area compared with discrete buffers, while the 2.3 V to 5.5 V range supports both low-voltage and conventional 5 V embedded products. Firmware should initialize every port direction before driving a load and use the interrupt output when avoiding continuous bus polling.
Embedded Sensor and Discrete Input Interface
The PCA9536DRG4 can bring several slow-changing digital sensor or switch signals back to a host controller over I2C. Its input-port and polarity-inversion registers allow firmware to present a consistent logic level even when external hardware uses active-low signaling. Because the device supports operation from 2.3 V to 5.5 V, it can sit alongside low-voltage embedded processors while communicating through the same two-wire bus. The four-bit granularity is most appropriate for compact sensor nodes where adding a larger, higher-pin-count GPIO controller would increase board area and design complexity.
Programmable Relay and Control Output
The PCA9536DRG4 can control small enable, relay-driver, reset, or interlock signals when the final load is driven by suitable external circuitry. Four independently selectable output bits reduce the number of host GPIO pins required for multi-channel control, and the output register allows firmware to update several signals in one bus transaction. The 400 kHz interface rate is far beyond the needs of typical slow relay or interlock systems, so update latency will usually be dominated by host firmware rather than the device itself. Verify output current, voltage, and timing limits in the manufacturer datasheet before connecting a load directly.
Remote Instrumentation I/O Node
The PCA9536DRG4 can serve as a small remote I/O node in test and measurement equipment where the main controller communicates over I2C and a set of auxiliary controls must be distributed locally. Its 4-bit port and configurable registers are useful for front-panel control lines, fixture status signals, and external trigger inputs. The low pin count and 8-SOIC footprint make board placement straightforward, while the 2.3 V to 5.5 V range allows integration across laboratory and embedded supply domains. Keep the expansion device close to the grounded signals it serves to reduce susceptibility to noise and communication errors.
Battery-Powered Sensor Node
The PCA9536DRG4 can expand control or sensing lines in a compact battery-powered embedded node where adding host-controller pins would reduce routing flexibility. Its 2.3 V minimum operating voltage supports low-energy logic systems, and the four configurable ports allow unused channels to be configured in the direction that minimizes unnecessary activity. The I2C interface shares two signal conductors with the host, reducing pin count and wiring. A designer should still verify standby current, I/O leakage, pull-up requirements, and the operating temperature range from the manufacturer datasheet before calculating a battery-life budget.
Data referensi engineering untuk PCA9536DRG4 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PCA9536DR | PCA9536DG4 | PCA9536D |
|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | 4-bit I2C and SMBus remote I/O expander | 4-bit I2C and SMBus remote I/O expander | 4-bit I2C and SMBus remote I/O expander | 4-bit I2C and SMBus remote I/O expander |
| Number of I/O Ports | 4 bits | 4 bits | 4 bits | 4 bits |
| Supply Voltage Range | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| Maximum I2C Bus Frequency | 400 kHz | 400 kHz | 400 kHz | 400 kHz |
| Interface | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus |
| Configuration Registers | 4-bit configuration, input, output, and polarity inversion | 4-bit configuration, input, output, and polarity inversion | 4-bit configuration, input, output, and polarity inversion | 4-bit configuration, input, output, and polarity inversion |
Diferensiator Kunci
- Same core 4-bit I/O platform with four independently configurable ports (vsPCA9536DR)
- Direct 400 kHz two-wire interface for shared embedded buses (vsPCA9536DG4)
- Configurable input, output, and polarity behavior in an 8-SOIC footprint (vsPCA9536D)
Catatan Desain
Assign the 8-SOIC footprint only after checking pin 1 orientation and the manufacturer pin-description diagram. Route SDA and SCL away from switching nodes and maintain a continuous ground reference beneath the device. Place the local supply-decoupling capacitor close to VCC and GND, and follow the manufacturer layout guidance for the interrupt trace so that a noisy or long INT route does not interfere with the bus interface.
Size the SDA and SCL pull-ups for the actual bus voltage, total capacitance, wiring length, and selected speed rather than copying a single resistance value. The device supports 400 kHz operation, but slower buses can permit stronger pull-ups and improved rise-time margin. Check every pull-up contribution when multiple expanders share the bus, and avoid pull-up voltages above the host or PCA9536DRG4 supply limits.
Do not treat a matching SOIC package as sufficient proof that every ordering suffix is interchangeable. Verify the ordering code for tape-and-reel orientation, lead finish, package dimensions, device address, lifecycle status, and temperature grade. Program every port direction before driving it, account for the power-on state of external circuitry, and confirm the interrupt polarity in firmware because an active-low control signal may otherwise trigger an unintended response.
Informasi Konformitas
No explicit environmental or automotive qualification statements were included in the available product records. Confirm RoHS, REACH, lead-free, halogen-free, and qualification status from the current Texas Instruments product and ordering documentation.