Texas Instruments

PCA9536DRG4 - 4-Bit I2C I/O Expander | Texas Instruments

料号: PCA9536DRG4 ✓ 量产中
2.3 V to 5.5 V Vdss 8-pin SOIC, 0.154 inch (3.90 mm) width Package 400 kHz Speed
最小起订量: 1 |

PCA9536DRG4 概述

The Texas Instruments PCA9536DRG4 is a 4-bit I2C and SMBus remote I/O expander with configuration registers, operating from 2.3 V to 5.5 V at up to 400 kHz and housed in an 8-pin SOIC package. It adds four configurable digital I/O lines to a host controller while retaining independent input, output, and polarity-inversion registers. The PCA9536DRG4 is therefore an I/O expander, a bidirectional-bus interface device, and a power-management-adjacent interface IC for embedded systems.

An I/O expander is a peripheral integrated circuit that increases the number of general-purpose digital inputs and outputs available to a host microcontroller or processor. The host communicates with the PCA9536DRG4 through the two-wire I2C bus, using serial clock and serial data lines. The device supports both I2C and SMBus-style access, making it suitable for industrial controllers, embedded modules, and compact control systems that need additional GPIOs without enlarging the host device.

The principal specifications are a 4-bit I/O count, a 2.3 V to 5.5 V operating range, bus operation up to 400 kHz, and an 8-pin SOIC package. Configuration registers allow each of the four ports to be selected independently as an input or output. Separate input-port, output-port, and active-high or active-low polarity-inversion registers provide software-controlled behavior for connected sensors, interrupt signals, indicators, and control inputs.

The architecture places a small serial interface beside four independently configurable port pins. Because the port registers are remotely accessible over I2C, the host can read input states, update output levels, and invert input polarity without dedicating a host GPIO pin to every external signal. The active-low interrupt output provides a compact mechanism for notifying the host when a programmed input condition occurs, although the exact implemented behavior should be confirmed in the manufacturer datasheet and the host firmware.

Typical uses include expanding a microcontroller in a programmable logic controller, adding digital control lines to an embedded instrument, reading discrete industrial inputs, driving indicator or enable signals, and providing a small remote I/O node connected through an I2C bus. The 2.3 V minimum supply supports low-voltage embedded systems, while the 5.5 V maximum accommodates conventional 5 V logic environments when the host and bus levels are compatible.

PCB design should preserve the 8-SOIC footprint and place pull-up resistors for SDA and SCL according to the bus voltage, capacitance, and required rise time. Confirm the address arrangement, reset behavior, input default state, and interrupt polarity in the manufacturer datasheet before firmware and schematic sign-off. The fixed-address nature of this device also matters when multiple identical expanders share one bus.

This page consolidates the exact package and bus information with practical replacement guidance, design cautions, and application-focused engineering context. It also distinguishes the PCA9536DRG4 from related ordering variants so engineers can assess board-fit and register-level compatibility before approving a substitution.

直接替换替代料: PCA9536DRG4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: PCA9536DRG4 (相同外形与封装尺寸) ——差异在于 Configuration Registers, Package, Product Type.

Texas Instruments
Configuration Registers: Present
Package: 8-SOIC
Product Type: 4-bit I2C/SMBus GPIO expander
对比 PCA9536DRG4 →
Texas Instruments
Configuration Registers: Yes
Package: 8-pin SOIC
Product Type: 4-bit I2C/SMBus remote I/O expander
对比 PCA9536DRG4 →
Texas Instruments
Configuration Registers: Present
Package: 8-SOIC
Product Type: 4-bit I2C/SMBus GPIO expander
对比 PCA9536DRG4 →

PCA9536DR

✅ 直接替换
Texas Instruments
📦 8-SOIC
4-bit I2C/SMBus GPIO expander · 4 · 2.3 V to 5.5 V · 400 kHz · I2C/SMBus · Present · 8-pin CMOS device · General-purpose parallel input/output

联系询价

查看数据手册 →

PCA9536DG4

✅ 直接替换
Texas Instruments
📦 8-SOIC
4-bit I2C/SMBus remote I/O expander · 4 · 2.3 V to 5.5 V · 400 kHz · 1 uA maximum · 0.15 mA maximum · 85 C · 8-pin SOIC

联系询价

查看数据手册 →

PCA9536D

✅ 直接替换
Texas Instruments
📦 8-SOIC
4-bit I2C/SMBus GPIO expander · 4 · 2.3 V to 5.5 V · 400 kHz · I2C/SMBus · Present · 8-pin CMOS device · General-purpose parallel input/output

联系询价

查看数据手册 →

PCA9536DRG4 规格参数

Product Type 4-bit I2C and SMBus remote I/O expander
Number of I/O Ports 4 bits
Supply Voltage Range 2.3 V to 5.5 V
Maximum I2C Bus Frequency 400 kHz
接口类型 I2C and SMBus
Configuration Registers 4 configuration bits, one for each I/O
Input Port Register 1 register
Output Port Register 1 register
Polarity Inversion Register 1 register with active-high or active-low selection
封装 8-pin SOIC, 0.154 inch (3.90 mm) width
安装类型 Surface mount

PCA9536DRG4 引脚配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
引脚 1 INT — Interrupt output
引脚 2 P3 — Configurable I/O port 3
引脚 3 P2 — Configurable I/O port 2
引脚 4 P1 — Configurable I/O port 1
引脚 5 P0 — Configurable I/O port 0
引脚 6 GND — Ground
引脚 7 SCL — Serial clock
引脚 8 SDA — Serial data

典型应用

PCA9536DRG4 适用于 6 应用s: Industrial PLC Discrete I/O Expansion, Microcontroller Button and Indicator Expansion, Embedded Sensor and Discrete Input Interface, Programmable Relay and Control Output, Remote Instrumentation I/O Node, Battery-Powered Sensor Node.

🏭

Industrial PLC Discrete I/O Expansion

The PCA9536DRG4 fits a compact PLC or industrial controller that needs additional discrete inputs and outputs without enlarging the host processor package. Its four bits can be configured independently as inputs or outputs, while the 2.3 V to 5.5 V operating range accommodates common control-system supply levels. Connecting the device through SDA and SCL preserves the two-wire bus architecture, and the configuration registers allow software to adapt each port as field wiring changes. Because the interface operates up to 400 kHz, several compatible devices can share a suitably designed bus. Designers must confirm the fixed address against other peripherals and select pull-ups for the actual bus voltage and capacitance.

🔧

Microcontroller Button and Indicator Expansion

The PCA9536DRG4 is useful when a microcontroller has insufficient GPIOs for front-panel buttons, status LEDs, mode controls, or discrete enable signals. Its 4-bit port can mix input and output functions, and separate input, output, and polarity-inversion registers simplify software handling of active-low buttons or active-high indicators. The 8-SOIC package preserves PCB area compared with discrete buffers, while the 2.3 V to 5.5 V range supports both low-voltage and conventional 5 V embedded products. Firmware should initialize every port direction before driving a load and use the interrupt output when avoiding continuous bus polling.

🧩

Embedded Sensor and Discrete Input Interface

The PCA9536DRG4 can bring several slow-changing digital sensor or switch signals back to a host controller over I2C. Its input-port and polarity-inversion registers allow firmware to present a consistent logic level even when external hardware uses active-low signaling. Because the device supports operation from 2.3 V to 5.5 V, it can sit alongside low-voltage embedded processors while communicating through the same two-wire bus. The four-bit granularity is most appropriate for compact sensor nodes where adding a larger, higher-pin-count GPIO controller would increase board area and design complexity.

⚡

Programmable Relay and Control Output

The PCA9536DRG4 can control small enable, relay-driver, reset, or interlock signals when the final load is driven by suitable external circuitry. Four independently selectable output bits reduce the number of host GPIO pins required for multi-channel control, and the output register allows firmware to update several signals in one bus transaction. The 400 kHz interface rate is far beyond the needs of typical slow relay or interlock systems, so update latency will usually be dominated by host firmware rather than the device itself. Verify output current, voltage, and timing limits in the manufacturer datasheet before connecting a load directly.

📡

Remote Instrumentation I/O Node

The PCA9536DRG4 can serve as a small remote I/O node in test and measurement equipment where the main controller communicates over I2C and a set of auxiliary controls must be distributed locally. Its 4-bit port and configurable registers are useful for front-panel control lines, fixture status signals, and external trigger inputs. The low pin count and 8-SOIC footprint make board placement straightforward, while the 2.3 V to 5.5 V range allows integration across laboratory and embedded supply domains. Keep the expansion device close to the grounded signals it serves to reduce susceptibility to noise and communication errors.

🔋

Battery-Powered Sensor Node

The PCA9536DRG4 can expand control or sensing lines in a compact battery-powered embedded node where adding host-controller pins would reduce routing flexibility. Its 2.3 V minimum operating voltage supports low-energy logic systems, and the four configurable ports allow unused channels to be configured in the direction that minimizes unnecessary activity. The I2C interface shares two signal conductors with the host, reducing pin count and wiring. A designer should still verify standby current, I/O leakage, pull-up requirements, and the operating temperature range from the manufacturer datasheet before calculating a battery-life budget.

What is the PCA9536DRG4 and what does it do?
The PCA9536DRG4 is a 4-bit remote I/O expander that communicates with a host controller through I2C or SMBus. According to the Texas Instruments product page, it provides four configurable I/O lines, a 2.3 V to 5.5 V operating range, and configuration registers. Each port can be programmed independently as an input or output, making the device useful when a microcontroller or PLC has too few GPIOs for external buttons, indicators, relays, or discrete sensors.
What is the operating voltage range of PCA9536DRG4?
The PCA9536DRG4 operates from 2.3 V to 5.5 V. The Texas Instruments PCA9536 product page identifies the device as a 4-bit I2C/SMBus I/O expander designed for 2.3 V to 5.5 V VCC operation. This range supports both low-voltage embedded systems and 5 V logic environments, but SDA and SCL pull-ups must use a voltage compatible with the connected host and bus.
How many I/O pins does the PCA9536DRG4 have?
The PCA9536DRG4 has four independently configurable I/O lines. The Texas Instruments product description identifies it as a 4-bit I2C/SMBus I/O expander with separate configuration, input-port, output-port, and polarity-inversion registers. These registers allow software to select each port as input or output and to control polarity, although the exact electrical state of each pin during reset should be confirmed from the manufacturer datasheet.
What is the maximum I2C bus speed of PCA9536DRG4?
The PCA9536DRG4 supports I2C bus operation up to 400 kHz. The Texas Instruments product page and the component listing identify it as an I2C/SMBus expander with a maximum bus frequency of 400 kHz. Actual bus speed still depends on pull-up resistance, total bus capacitance, wiring length, and the electrical limits of every device connected to the same SDA and SCL lines.
Where can I download the PCA9536DRG4 datasheet PDF?
The official PCA9536 datasheet is available through the Texas Instruments product page at https://www.ti.com/product/PCA9536, which links to the manufacturer documentation and ordering information. The product is identified as a remote 4-bit I2C and SMBus I/O expander with configuration registers. Use the pin-description table, electrical characteristics, register map, and application information from that document when assigning PCB tracks and writing device firmware.
Where can I find the PCA9536DRG4 pinout?
The PCA9536DRG4 uses an 8-pin SOIC package, and the manufacturer datasheet provides the authoritative pin-description diagram. The eight connections are INT, P3, P2, P1, P0, GND, SCL, and SDA when viewed in the standard SOIC numbering sequence. Use the Texas Instruments datasheet to cross-check pin orientation, exposed functionality, and recommendations for bypassing and bus pull-ups before assigning the PCB footprint.
What is the best drop-in replacement for PCA9536DRG4?
PCA9536DR is the closest same-footprint ordering option identified for the PCA9536DRG4 because it retains the 4-bit I/O configuration, 2.3 V to 5.5 V supply range, 400 kHz bus operation, and 8-SOIC package. No broader set of five or more technically distinct drop-in replacements could be established from the available records. Treat the DR and DRG4 ordering codes as configuration and packaging variants, and verify the required reel, finish, and environmental order details before substitution.
Can PCA9536DG4 replace PCA9536DRG4?
PCA9536DG4 may be considered for review because comparison records associate it with the same PCA9536D family and an 8-pin SOIC implementation. Before using it as a drop-in replacement, confirm the manufacturer ordering table for package, lead finish, tape orientation, and the exact I2C address. Also verify the interrupt and register behavior in the datasheet because a valid package match alone does not guarantee every ordering suffix has identical qualification or lifecycle requirements.
Is PCA9536DRG4 the same as PCA9536DR?
The PCA9536DRG4 is an ordering designation within the PCA9536DR device family and retains the core 4-bit I2C/SMBus expander function. The visible distinction is in the ordering suffix, which commonly identifies packaging or material configuration. The Texas Instruments ordering information must be used to determine whether the suffix changes tape-and-reel presentation, lead finish, or another procurement attribute rather than changing the electrical function.
When should I choose PCA9536DRG4 instead of PCA9536DG4?
Choose PCA9536DRG4 when its specific packaging and material configuration match the assembly process and purchasing requirements of the design. The functional platform remains a 4-bit, 2.3 V to 5.5 V I2C/SMBus expander in an 8-SOIC package. The deciding factors should be the ordering table, reel configuration, lead finish, traceability requirements, and lifecycle status rather than an assumed difference in I/O count or bus speed.
Where can I buy PCA9536DRG4 and check its current lead time?
Use the Request a Quote form on this page to request PCA9536DRG4 availability, current pricing, minimum order quantity, and lead time. The component is listed as an 8-SOIC I/O expander by Texas Instruments, and distributor records identify an in-stock quantity without a qualifying quantity-break price table. A separate commercial request is therefore the appropriate way to confirm assembly packaging, schedule, and shipment details.
Is PCA9536DRG4 in stock?
PCA9536DRG4 availability should be confirmed through the Request a Quote form on this page before an order is scheduled. A distributor product record shows an in-stock quantity, but that figure is not a permanent inventory guarantee and may not reflect your required packaging or shipment destination. The Request a Quote response can confirm current stock, allocation, quantity breaks, and expected delivery for the exact MPN.
What is the price of PCA9536DRG4?
Use the Request a Quote form on this page for the current PCA9536DRG4 price and quantity breaks. The available product listings do not print a qualifying price table for the exact MPN, so a current unit figure cannot be reliably extracted for display. The quote process can also account for the required reel configuration, order quantity, and any required traceability before an order is placed.
How do I design the I2C bus for PCA9536DRG4?
Connect SDA and SCL to the host bus and choose pull-up resistors that satisfy the bus voltage, total capacitance, and target rise time at the selected operating frequency. The PCA9536DRG4 supports operation up to 400 kHz, but the complete bus must also meet that timing target. Keep the route short, use a common ground plane, and follow the manufacturer application guidance for decoupling and pull-up placement.
What are the key specifications of PCA9536DRG4 that engineers should know?
The PCA9536DRG4 combines four configurable I/O ports, a 2.3 V to 5.5 V supply range, I2C/SMBus communication, operation up to 400 kHz, and an 8-pin SOIC package in one interface IC. Texas Instruments describes dedicated configuration, input, output, and polarity-inversion registers. The central design trade-off is added I/O capacity in a small package versus a fixed shared-bus address and the need to allocate host pins for SDA, SCL, power, ground, and interrupt handling.

工程参考数据: PCA9536DRG4 ——对比、设计指导和合规信息。

选型指南

Choose the PCA9536DRG4 for a compact 8-SOIC design that needs exactly four remotely configurable digital I/O lines over an I2C or SMBus bus. Its 2.3 V to 5.5 V supply range is suitable for both low-voltage embedded systems and conventional 5 V logic, while the configuration, input, output, and polarity registers simplify mixed input/output assignments. PCA9536DR is a closely related ordering choice when its lead-finish and packaging configuration better match procurement or assembly. PCA9536DG4 may also fit an 8-SOIC design, but the exact ordering details must be checked before board or firmware release. PCA9536D provides another family-level option, again requiring confirmation of the final suffix. For every option, verify the fixed bus address against other peripherals, calculate pull-ups for the actual bus, and review the manufacturer ordering table before approving a substitution.

与替代料对比

参数 本产品 PCA9536DR PCA9536DG4 PCA9536D
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Product Type 4-bit I2C and SMBus remote I/O expander 4-bit I2C and SMBus remote I/O expander 4-bit I2C and SMBus remote I/O expander 4-bit I2C and SMBus remote I/O expander
Number of I/O Ports 4 bits 4 bits 4 bits 4 bits
Supply Voltage Range 2.3 V to 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V
Maximum I2C Bus Frequency 400 kHz 400 kHz 400 kHz 400 kHz
Interface I2C and SMBus I2C and SMBus I2C and SMBus I2C and SMBus
Configuration Registers 4-bit configuration, input, output, and polarity inversion 4-bit configuration, input, output, and polarity inversion 4-bit configuration, input, output, and polarity inversion 4-bit configuration, input, output, and polarity inversion

关键差异点

  • Same core 4-bit I/O platform with four independently configurable ports (对比 PCA9536DR)
  • Direct 400 kHz two-wire interface for shared embedded buses (对比 PCA9536DG4)
  • Configurable input, output, and polarity behavior in an 8-SOIC footprint (对比 PCA9536D)

设计说明

Assign the 8-SOIC footprint only after checking pin 1 orientation and the manufacturer pin-description diagram. Route SDA and SCL away from switching nodes and maintain a continuous ground reference beneath the device. Place the local supply-decoupling capacitor close to VCC and GND, and follow the manufacturer layout guidance for the interrupt trace so that a noisy or long INT route does not interfere with the bus interface.

Size the SDA and SCL pull-ups for the actual bus voltage, total capacitance, wiring length, and selected speed rather than copying a single resistance value. The device supports 400 kHz operation, but slower buses can permit stronger pull-ups and improved rise-time margin. Check every pull-up contribution when multiple expanders share the bus, and avoid pull-up voltages above the host or PCA9536DRG4 supply limits.

Do not treat a matching SOIC package as sufficient proof that every ordering suffix is interchangeable. Verify the ordering code for tape-and-reel orientation, lead finish, package dimensions, device address, lifecycle status, and temperature grade. Program every port direction before driving it, account for the power-on state of external circuitry, and confirm the interrupt polarity in firmware because an active-low control signal may otherwise trigger an unintended response.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

No explicit environmental or automotive qualification statements were included in the available product records. Confirm RoHS, REACH, lead-free, halogen-free, and qualification status from the current Texas Instruments product and ordering documentation.

数据核验日期: 2026-11-14 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

PCA9536DRG4 datasheet PCA9536DRG4 pinout PCA9536DRG4 datasheet pdf PCA9536DRG4 equivalent PCA9536DRG4 replacement PCA9536DRG4 cross reference PCA9536DRG4 footprint PCA9536DRG4 application circuit PCA9536DRG4 vs PCA9536DR Texas Instruments PCA9536DRG4 PCA9536DRG4 price PCA9536DRG4 stock

相关元器件 & 术语

Texas Instruments PCA9536DRG4 PCA9536DR PCA9536DG4 PCA9536D I/O expander interface IC I2C SMBus serial clock serial data GPIO configuration register input port register output port register polarity inversion 2.3 V to 5.5 V 400 kHz 8-SOIC SOIC family surface-mount package SMD interrupt output PLC microcontroller
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情