PCA9665D - Fm+ Parallel to I2C Controller | NXP | 20-SO
MPN: PCA9665D ✗ Akhir HidupPCA9665D Ringkasan
An I2C bus controller is an interface IC that converts commands and data from a parallel or processor-specific bus into transactions on an I2C serial bus. The I2C interface uses SDA for bidirectional data and SCL for the clock, while the parallel side communicates with a host using a dedicated address and data register arrangement. This device family is useful when a controller, display subsystem, communications equipment, or embedded logic platform needs to access low-speed I2C peripherals without using an I2C-capable host controller.
The PCA9665D is identified by NXP as an Fm+ parallel bus to I2C-bus controller. Its 20-pin SOIC package supports conventional surface-mount assembly and provides a practical upgrade path for designs that require a dedicated parallel-to-I2C bridge. The 2.5 V to 3.3 V operating range is compatible with low-voltage digital systems, while the approximately 100 uA supply current is important in equipment where the interface must not create an unnecessary standing load. Detailed clock, addressing, electrical, and timing limits should be taken from the manufacturer datasheet.
Typical uses include industrial control panels, programmable-logic-based peripherals, test systems, communication modules, display-control boards, and embedded equipment that exposes an I2C bus through a parallel host interface. The PCA9665D is especially useful when the existing host processor does not provide a suitable I2C peripheral. In such designs, the parallel interface can be connected to external logic or a processor bus, while the I2C side reaches sensors, EEPROMs, expanders, and other compatible devices.
When laying out a replacement design, verify the exact package variant, supply voltage, address behavior, clock timing, and signal levels against the NXP datasheet before production release. The D suffix denotes the 20-pin SO option, while other NXP order codes may use different package or shipping arrangements. Check the mechanical drawing and pin table for the selected ordering code rather than assuming every PCA9665-family order code has the same footprint.
Alternatif penggantian untuk PCA9665D — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
PCA9665A
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PCA9665ADP
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PCA9665D Spesifikasi
| Device Type | Fm+ parallel bus to I2C-bus controller |
| Controller Type | I2C bus controller |
| Parallel Interface | 8-bit parallel bus |
| Serial Interface | I2C bus |
| Supply Voltage Range | 2.5 V to 3.6 V |
| Nominal Operating Supply | 2.5 V or 3.3 V |
| Arus Pemuat | 100 uA |
| Paket | 20-pin SOIC |
| Package Dimensions | 7.50 mm width |
| Tipe Mounting | Surface mount |
| Product Lifecycle | No longer manufactured |
PCA9665D 7.50 mm width Diamant Konfigurasi Panduan
Konfigurasi pin untuk PCA9665D (7.50 mm width pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk PCA9665D.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
PCA9665D cocok untuk 6 aplikasis: Programmable Logic to I2C Peripheral Bridge, Industrial Control Panel Interface, Test and Measurement Control Module, Communications Equipment Peripheral Hub, Display and Audio Control Subsystem, Embedded Sensor and EEPROM Hub.
Programmable Logic to I2C Peripheral Bridge
The NXP PCA9665D fits programmable-logic systems that need to control I2C sensors, EEPROMs, or expanders without implementing serial timing in logic fabric. The parallel side accepts host commands while the controller handles I2C-bus transactions, simplifying the architecture and reducing host firmware involvement. Its 2.5 V to 3.6 V supply range fits common 3.3 V logic systems, while approximately 100 uA supply current keeps the standing load moderate. Because PCA9665D is no longer manufactured, an existing board can use it for controlled maintenance, but a new design should validate the PCA9665A or PCA9665ADP option against the required package, timing, and register behavior.
Direkomendasikan
Industrial Control Panel Interface
PCA9665D can connect a parallel control section to I2C-managed display drivers, configuration EEPROMs, sensors, or I/O expanders in an industrial panel. The 20-pin SOIC format supports conventional surface-mount assembly, and the 2.5 V to 3.3 V nominal operation suits low-voltage control electronics. Its approximately 100 uA supply current is useful where the interface remains active continuously. For new production, engineers should treat the obsolete status as a supply-risk issue and confirm that any replacement preserves the pin arrangement, command timing, clock limit, and electrical limits documented by NXP.
Direkomendasikan
Test and Measurement Control Module
The PCA9665D is suitable for test modules that coordinate I2C peripherals through a parallel logic interface. It can bridge a tester controller or programmable instrument toward sensors, memories, and low-speed measurement components while operating from a 2.5 V to 3.3 V supply. The approximately 100 uA supply current avoids making the interface a major standing-power contributor. A replacement design must preserve timing margin at the intended I2C clock rate and should account for the D revision's no-longer-manufactured lifecycle through controlled sourcing and full board-level validation.
Direkomendasikan
Communications Equipment Peripheral Hub
In communications hardware, PCA9665D can provide a dedicated path from a parallel system bus to I2C configuration or monitoring devices. This architecture is useful when a communication processor lacks spare I2C resources or when multiple board-level functions require a controlled bus bridge. The 2.5 V to 3.6 V operating range supports conventional digital rails, and the approximately 100 uA supply current suits embedded equipment. For production continuity, engineers should compare a currently obtainable NXP-family part for identical pin behavior, signal levels, address handling, and timing before declaring it a direct replacement.
Direkomendasikan
Display and Audio Control Subsystem
PCA9665D can serve low-speed control peripherals in a display or audio subsystem, including I2C display controllers, volume devices, interface expanders, and configuration memories. A parallel host section can issue commands without tying the subsystem's main processor to the I2C protocol. The 20-pin SOIC package is appropriate for compact controller boards, while the 2.5 V to 3.3 V operating range aligns with many mixed-signal subsystems. Designers should verify logic thresholds and timing carefully during any replacement, particularly for display update paths where bus latency or an address-map difference could affect operation.
Direkomendasikan
Embedded Sensor and EEPROM Hub
The PCA9665D can connect a parallel embedded subsystem to I2C sensors, EEPROMs, and low-power peripheral ICs. Its approximately 100 uA supply current is valuable in compact equipment where the interface must coexist with always-on monitoring functions. The 2.5 V to 3.6 V supply range supports both 2.5 V and 3.3 V designs, subject to the detailed electrical requirements in the manufacturer datasheet. Since NXP lists PCA9665D as no longer manufactured, existing deployments may use controlled retained inventory, while new boards should evaluate PCA9665A or PCA9665ADP and verify pin, clock, and register compatibility.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PCA9665D — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PCA9665A | PCA9665ADP |
|---|---|---|---|
| Device Function | Fm+ parallel bus to I2C-bus controller | Parallel-to-I2C controller in the PCA9665 family | PCA9665-family parallel-to-I2C controller |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 20-pin SOIC | 20-pin SOIC | 20-pin SOIC |
| Mounting Type | Surface mount | Surface mount | Surface mount |
Diferensiator Kunci
- Dedicated parallel-to-I2C controller function (vsPCA9665A)
- Low standby consumption for an interface bridge (vsPCA9665ADP)
- Established 20-pin SOIC footprint for legacy maintenance (vsPCA9665A)
Catatan Desain
Do not treat PCA9665, PCA9665A, and other related order codes as automatically interchangeable. NXP groups the PCA9665 and PCA9665A devices under one data-sheet family, but revision behavior, temperature grade, and ordering options can differ. Before substitution, compare the exact pin table, package drawing, supply limits, I2C clock timing, address configuration, command registers, and reset requirements. For a legacy repair, preserving the original footprint and avoiding changes to the parallel host timing are the safest priorities.
Lay out the PCA9665D as a standard 20-pin SOIC device and route the I2C SDA and SCL signals as a compact, controlled bus. Keep the parallel-side traces away from the serial interface when possible to reduce coupling into sensitive edges. Confirm whether the selected design requires pull-up resistors on SDA and SCL, use the values and capacitance limits specified by NXP, and avoid long stubs that increase capacitive loading and signal-integrity risk.
Design the interface supply around the manufacturer's 2.5 V to 3.6 V range and the approximately 100 uA supply-current specification. Place local supply decoupling close to the device and keep the return path short, but do not assume the operating current remains at 100 uA under every bus state because dynamic activity and external loads can affect the total demand. Review the complete electrical characteristics and absolute maximum ratings before setting voltage tolerances or adding downstream loading.
The PCA9665D's I2C timing margin depends on bus capacitance, clock rate, pull-up strength, and the behavior of connected peripherals. Calculate the effective bus capacitance and verify rise times at the intended I2C frequency rather than copying a nominal clock limit from another member of the family. Keep SCL and SDA routing symmetrical where practical, minimize stub lengths, and test the slowest and fastest peripheral operating conditions on the completed board.
Informasi Konformitas
NXP's official product page confirms the product identity and no-longer-manufactured lifecycle status but does not provide extractable compliance declarations in the cited material. Compliance fields remain unknown rather than being inferred.