PCF8575RGER - 16-Bit I/O Expander | Texas Instruments
MPN: PCF8575RGER ✓ AktifPCF8575RGER Ringkasan
An I/O expander is an interface IC that increases the number of general-purpose input and output pins available to a digital system without requiring a larger host controller. In the hierarchy of electronic components, the PCF8575RGER is an I/O expander, interface IC, and semiconductor. Its parallel port can be used for control signals, keypad scanning, relay or LED drive, and sensing digital status lines.
The PCF8575RGER provides 16 I/O pins, a 2.5 V to 5.5 V supply range, 400 kHz bus operation, and an interrupt output. Its operating temperature range is -40 °C to 85 °C according to the Texas Instruments product page. The interrupt output allows the connected controller to remain informed of input changes without continuously polling the expander, reducing unnecessary bus transactions in event-driven systems.
The device is designed for both writing output data and reading input states through the serial bus. Each port bit can be configured by software as input or output, while the electrical characteristics support common embedded-system interfacing. The compact VQFN-24 (RGE) package helps reduce board area in space-constrained consumer, industrial, and communications equipment.
Typical applications include expanding keypad and display-control lines, driving discrete LEDs, monitoring switches and sensors, controlling relays or solenoids through suitable driver circuitry, and adding general-purpose digital I/O to an embedded controller. In each case, the I2C or SMBus connection simplifies the host interface while preserving a parallel-style port for external circuitry.
When laying out the PCB, place the device close to the connected I/O circuitry and route the serial bus away from noisy switching nodes. Confirm the exposed-pad connection and thermal layout against the manufacturer datasheet. Use appropriate pull-up resistors for the I2C bus and account for the open-drain interrupt output when designing the host-side signal path.
This product page combines the PCF8575RGER ordering information, functional characteristics, application guidance, and same-footprint alternatives with practical PCB considerations. It is intended to help engineers identify the correct Texas Instruments package option and plan a reliable interface expansion design.
Alternatif penggantian untuk PCF8575RGER — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
PCF8575RGERG4
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PCF8575CRGER
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PCF8575RGER Spesifikasi
| Product Type | 16-bit remote I/O expander with interrupt output |
| Number of I/O Ports | 16 |
| Supply Voltage Range | 2.5 V to 5.5 V |
| Bus Interface | I2C/SMBus |
| Maximum Bus Frequency | 400 kHz |
| Interrupt Output | Present |
| Rentang Suhu Kerja | -40 °C to 85 °C |
| Paket | VQFN-24 (RGE) |
| Package Dimensions | 4 mm x 4 mm |
| Jumlah Pin | 24 |
| Tipe Mounting | Surface mount |
| I/O Port Configuration | Software-configurable input or output |
PCF8575RGER 4 mm x 4 mm Diamant Konfigurasi Panduan
Konfigurasi pin untuk PCF8575RGER (4 mm x 4 mm pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk PCF8575RGER.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
PCF8575RGER cocok untuk 6 aplikasis: Embedded Keypad and Control Expansion, LED and Indicator Control, Digital Switch and Sensor Monitoring, Relay and Solenoid Interface Expansion, Communications Equipment Port Expansion, IoT Sensor and Peripheral Hub.
Embedded Keypad and Control Expansion
The PCF8575RGER is suitable for adding keypad rows, column sense lines, and control outputs to a microcontroller with limited direct I/O. Its 16 port bits connect to switches or a keypad matrix through the host's I2C interface, while the interrupt output can alert the controller when an input changes. The 2.5 V to 5.5 V operating range supports common 3.3 V and 5 V embedded platforms, and the 24-pin VQFN package keeps the circuit compact. Firmware can scan and debounce the keypad, update output states, and use the interrupt to avoid continuous polling.
Direkomendasikan
LED and Indicator Control
The PCF8575RGER can provide a compact parallel output port for LED indicators, status lamps, and segmented-display controls when the selected port currents remain within the device electrical limits. The host writes output patterns over I2C or SMBus at rates up to 400 kHz, allowing many indicators to share the serial bus. Quasi-bidirectional I/O behavior should be checked against the exact load and drive requirements in the manufacturer datasheet. The 24-pin VQFN-24 package reduces board area compared with a larger through-hole or fine-pitch alternative.
Direkomendasikan
Digital Switch and Sensor Monitoring
The PCF8575RGER can monitor multiple digital switches, interlocks, or sensor status signals through its 16-bit port. Inputs are read over the I2C or SMBus interface, and the interrupt output provides a change indication so the controller can respond to events without repeatedly polling. This arrangement is useful in industrial control, appliance, and instrumentation products where several distributed logic signals would otherwise consume host pins. The 2.5 V to 5.5 V range and -40 °C to 85 °C operating range support a broad range of embedded equipment.
Direkomendasikan
Relay and Solenoid Interface Expansion
The PCF8575RGER can serve as the serial command interface for relays, solenoids, valves, or other actuators when external transistor or MOSFET driver stages are used. The host controls the 16 port bits through I2C or SMBus, while the driver circuitry isolates the expander from inductive loads and handles required flyback protection. The interrupt feature is less central in this use case because actuator states are generally commanded rather than sensed. Verify each port's voltage, current, and timing limits before assigning drive duties.
Direkomendasikan
Communications Equipment Port Expansion
The PCF8575RGER can add discrete control and status lines to communications equipment without enlarging the primary host controller. It can supervise module-present, reset, enable, fault, or alarm signals while the I2C or SMBus connection handles configuration. The interrupt output allows the host to react to status transitions, which is helpful in network appliances and industrial communication systems. Its 24-pin VQFN RGE package supports compact board layouts while maintaining a 2.5 V to 5.5 V interface supply range.
Direkomendasikan
IoT Sensor and Peripheral Hub
The PCF8575RGER can expand an IoT controller for low-speed peripheral attachment, including digital sensors, configuration switches, and alarm lines. Its interrupt output supports event-driven sensing, allowing the host to remain idle until an input state changes. The 400 kHz maximum bus rate is appropriate for control and status traffic rather than high-bandwidth sensor streaming. The 2.5 V to 5.5 V supply range and compact 4 mm by 4 mm VQFN-24 package are useful in space-constrained connected products.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PCF8575RGER — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PCF8575RGERG4 | PCF8575CRGER |
|---|---|---|---|
| Package | VQFN-24 (RGE), 4 mm x 4 mm | VQFN-24, same package | VQFN-24 (RGE), 4 mm x 4 mm |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of I/O | 16 | 16 | 16 |
| Supply Voltage Range | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
| Serial Interface | I2C/SMBus | I2C/SMBus | I2C/SMBus |
| Maximum Bus Frequency | 400 kHz | 400 kHz | 400 kHz |
| Interrupt Output | Present | Present | Present |
Diferensiator Kunci
- Same-package family option (vsPCF8575RGERG4)
- Compact 16-I/O expansion (vsPCF8575CRGER)
- Event-driven host interaction (vsPCF8575CRGER)
Catatan Desain
Use the Texas Instruments RGE package drawing for land pattern, exposed-pad connection, solder mask, and paste geometry. The PCF8575RGER is a 24-pin VQFN in a 4 mm by 4 mm body, so pad and via dimensions should not be copied from a generic 24-pin QFN. Place the device near the external I/O circuitry and route the I2C and interrupt nets away from switching nodes.
Place the local supply-decoupling capacitor close to the device power and ground pins, and verify the capacitor voltage rating and ESR suitability against the manufacturer's recommended circuit. The supported 2.5 V to 5.5 V range does not eliminate the need for clean power. Confirm that the I2C pull-up voltage and any external pull-up network remain compatible with both the expander and the host controller.
Keep SDA and SCL routes short, use a continuous ground reference, and avoid stubs where practical. The supported bus rate is 400 kHz, but actual timing depends on total bus capacitance, pull-up resistance, clock stretching, and PCB delay. Treat the interrupt output as an open-drain signal when the manufacturer documentation specifies that implementation and size any external pull-up accordingly.
Do not assume every port condition is suitable for direct relay, solenoid, or high-current LED drive. Check the absolute maximum ratings, per-port drive limits, and output transition behavior in the manufacturer datasheet. Use external drivers for inductive loads and provide flyback protection. Also avoid changing an output from input mode without accounting for the PCF8575 quasi-bidirectional port behavior.
Informasi Konformitas
Compliance declarations are not present in the available product-page and distributor excerpts. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals status for the exact orderable MPN with Texas Instruments before release.