Texas Instruments

PCF8575RGER - 16-Bit I/O Expander | Texas Instruments

부품 번호: PCF8575RGER ✓ 활성
2.5 V to 5.5 V Vdss VQFN-24 (RGE) Package 400 kHz Speed
MOQ: 1 |

PCF8575RGER 개요

The Texas Instruments PCF8575RGER is a 16-bit remote I/O expander with an interrupt output, designed for I2C and SMBus communication at up to 400 kHz. It operates from 2.5 V to 5.5 V and is packaged in a 24-pin VQFN RGE package measuring 4 mm by 4 mm. The device adds 16 quasi-bidirectional I/O ports to a host microcontroller or embedded processor while providing an open-drain interrupt output for change detection.

An I/O expander is an interface IC that increases the number of general-purpose input and output pins available to a digital system without requiring a larger host controller. In the hierarchy of electronic components, the PCF8575RGER is an I/O expander, interface IC, and semiconductor. Its parallel port can be used for control signals, keypad scanning, relay or LED drive, and sensing digital status lines.

The PCF8575RGER provides 16 I/O pins, a 2.5 V to 5.5 V supply range, 400 kHz bus operation, and an interrupt output. Its operating temperature range is -40 °C to 85 °C according to the Texas Instruments product page. The interrupt output allows the connected controller to remain informed of input changes without continuously polling the expander, reducing unnecessary bus transactions in event-driven systems.

The device is designed for both writing output data and reading input states through the serial bus. Each port bit can be configured by software as input or output, while the electrical characteristics support common embedded-system interfacing. The compact VQFN-24 (RGE) package helps reduce board area in space-constrained consumer, industrial, and communications equipment.

Typical applications include expanding keypad and display-control lines, driving discrete LEDs, monitoring switches and sensors, controlling relays or solenoids through suitable driver circuitry, and adding general-purpose digital I/O to an embedded controller. In each case, the I2C or SMBus connection simplifies the host interface while preserving a parallel-style port for external circuitry.

When laying out the PCB, place the device close to the connected I/O circuitry and route the serial bus away from noisy switching nodes. Confirm the exposed-pad connection and thermal layout against the manufacturer datasheet. Use appropriate pull-up resistors for the I2C bus and account for the open-drain interrupt output when designing the host-side signal path.

This product page combines the PCF8575RGER ordering information, functional characteristics, application guidance, and same-footprint alternatives with practical PCB considerations. It is intended to help engineers identify the correct Texas Instruments package option and plan a reliable interface expansion design.

드롭인 대체품: PCF8575RGER — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

PCF8575RGERG4

✅ 드롭인
📦 VQFN-24 (RGE)
Same 24-pin VQFN package, 16 I/O pins, and 2.5 V to 5.5 V supply range; orderable suffix differs

📋 참조 대체품 (카탈로그에 없음)

PCF8575CRGER

✅ 드롭인
📦 VQFN-24 (RGE)
Same 24-pin VQFN package and 16-I/O, 400 kHz function; orderable suffix differs

📋 참조 대체품 (카탈로그에 없음)

PCF8575RGER 사양

Product Type 16-bit remote I/O expander with interrupt output
Number of I/O Ports 16
Supply Voltage Range 2.5 V to 5.5 V
Bus Interface I2C/SMBus
Maximum Bus Frequency 400 kHz
Interrupt Output Present
동작 온도 범위 -40 °C to 85 °C
패키지 VQFN-24 (RGE)
Package Dimensions 4 mm x 4 mm
핀 수 24
실장 유형 Surface mount
I/O Port Configuration Software-configurable input or output

PCF8575RGER 4 mm x 4 mm 핀 구성 가이드

PCF8575RGER(4 mm x 4 mm 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

PCF8575RGER의 4 mm x 4 mm 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: PCF8575RGER.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

PCF8575RGER 적합 용도: 6 애플리케이션s: Embedded Keypad and Control Expansion, LED and Indicator Control, Digital Switch and Sensor Monitoring, Relay and Solenoid Interface Expansion, Communications Equipment Port Expansion, IoT Sensor and Peripheral Hub.

🔧

Embedded Keypad and Control Expansion

The PCF8575RGER is suitable for adding keypad rows, column sense lines, and control outputs to a microcontroller with limited direct I/O. Its 16 port bits connect to switches or a keypad matrix through the host's I2C interface, while the interrupt output can alert the controller when an input changes. The 2.5 V to 5.5 V operating range supports common 3.3 V and 5 V embedded platforms, and the 24-pin VQFN package keeps the circuit compact. Firmware can scan and debounce the keypad, update output states, and use the interrupt to avoid continuous polling.

💡

LED and Indicator Control

The PCF8575RGER can provide a compact parallel output port for LED indicators, status lamps, and segmented-display controls when the selected port currents remain within the device electrical limits. The host writes output patterns over I2C or SMBus at rates up to 400 kHz, allowing many indicators to share the serial bus. Quasi-bidirectional I/O behavior should be checked against the exact load and drive requirements in the manufacturer datasheet. The 24-pin VQFN-24 package reduces board area compared with a larger through-hole or fine-pitch alternative.

🏭

Digital Switch and Sensor Monitoring

The PCF8575RGER can monitor multiple digital switches, interlocks, or sensor status signals through its 16-bit port. Inputs are read over the I2C or SMBus interface, and the interrupt output provides a change indication so the controller can respond to events without repeatedly polling. This arrangement is useful in industrial control, appliance, and instrumentation products where several distributed logic signals would otherwise consume host pins. The 2.5 V to 5.5 V range and -40 °C to 85 °C operating range support a broad range of embedded equipment.

⚡

Relay and Solenoid Interface Expansion

The PCF8575RGER can serve as the serial command interface for relays, solenoids, valves, or other actuators when external transistor or MOSFET driver stages are used. The host controls the 16 port bits through I2C or SMBus, while the driver circuitry isolates the expander from inductive loads and handles required flyback protection. The interrupt feature is less central in this use case because actuator states are generally commanded rather than sensed. Verify each port's voltage, current, and timing limits before assigning drive duties.

🌐

Communications Equipment Port Expansion

The PCF8575RGER can add discrete control and status lines to communications equipment without enlarging the primary host controller. It can supervise module-present, reset, enable, fault, or alarm signals while the I2C or SMBus connection handles configuration. The interrupt output allows the host to react to status transitions, which is helpful in network appliances and industrial communication systems. Its 24-pin VQFN RGE package supports compact board layouts while maintaining a 2.5 V to 5.5 V interface supply range.

🧩

IoT Sensor and Peripheral Hub

The PCF8575RGER can expand an IoT controller for low-speed peripheral attachment, including digital sensors, configuration switches, and alarm lines. Its interrupt output supports event-driven sensing, allowing the host to remain idle until an input state changes. The 400 kHz maximum bus rate is appropriate for control and status traffic rather than high-bandwidth sensor streaming. The 2.5 V to 5.5 V supply range and compact 4 mm by 4 mm VQFN-24 package are useful in space-constrained connected products.

What is the PCF8575RGER used for?
The PCF8575RGER is a 16-bit I2C and SMBus I/O expander used to add digital input and output lines to a microcontroller or embedded processor. According to the Texas Instruments product page, it provides a 2.5 V to 5.5 V operating range, 16 I/O pins, an interrupt output, and bus operation up to 400 kHz. It is useful for keypad scanning, switch monitoring, LED control, and other peripheral-connection tasks.
What is the operating voltage of the PCF8575RGER?
The PCF8575RGER operates from 2.5 V to 5.5 V. The Texas Instruments PCF8575 product page identifies the device as a 16-bit I2C and SMBus I/O expander with interrupt, while the PCF8575RGER ordering page identifies the RGE package and 24-pin construction. The supply range allows use in both 3.3 V and 5 V embedded systems.
Does the PCF8575RGER have an interrupt pin?
Yes, the PCF8575RGER includes an interrupt output. The manufacturer describes the PCF8575 as a 16-bit I2C and SMBus I/O expander with interrupt, and the ordering information for PCF8575RGER confirms the RGE package variant. The interrupt output lets the host controller respond to input changes instead of continuously polling the I/O port.
What is the bus speed of the PCF8575RGER?
The PCF8575RGER supports I2C and SMBus communication up to 400 kHz, as stated in the Texas Instruments product-page description and distributor listing. This bus rate is suitable for many embedded control systems that periodically transfer port data or configure output bits. Actual system operation must still satisfy the timing and pull-up requirements of the connected bus.
How many I/O pins does the PCF8575RGER provide?
The PCF8575RGER provides 16 I/O pins. Texas Instruments identifies the PCF8575 family as a 16-bit remote I/O expander, and the PCF8575RGER ordering page specifies a 24-pin VQFN RGE package. The 16 port bits can be individually configured as inputs or outputs through the serial interface.
Where can I download the PCF8575RGER datasheet?
The authoritative PCF8575RGER documentation is available through the Texas Instruments product page at https://www.ti.com/product/PCF8575 and the part-specific ordering page at https://www.ti.com/product/PCF8575/part-details/PCF8575RGER. These pages provide the manufacturer datasheet and ordering information. Use the pin-description table and electrical-characteristics section for PCB and firmware implementation.
Where can I find the PCF8575RGER pinout?
The PCF8575RGER pinout is shown in the Texas Instruments PCF8575 datasheet and its 24-pin RGE package documentation. The package is a 4 mm by 4 mm VQFN with 24 pins, so the exposed-pad and pin-assignment details must be checked against the manufacturer drawings rather than inferred from a generic 24-pin footprint. The PCF8575RGER ordering page confirms the RGE package designation.
Is the PCF8575RGER suitable for a 3.3 V microcontroller system?
Yes, the PCF8575RGER can be used with a 3.3 V system because its specified supply range is 2.5 V to 5.5 V. The I2C bus voltage and pull-up arrangement should be selected to match the logic levels used by the host and the expander. Confirm signal-level compatibility and the bus pull-up values in the manufacturer application guidance.
What is the difference between PCF8575RGER and PCF8575CRGER?
PCF8575RGER and PCF8575CRGER are listed as 16-bit, 400 kHz I/O expanders in the same 24-pin VQFN 4 mm by 4 mm format. The visible ordering data identifies different TI orderable suffixes, so the exact temperature, qualification, marking, or procurement characteristics should be compared on the manufacturer ordering pages. Both retain the same 16-I/O and interrupt-oriented device family.
Is the PCF8575RGER a drop-in replacement for PCF8575RGERG4?
PCF8575RGER and PCF8575RGERG4 are identified in the cross-reference comparison as Texas Instruments 24-pin VQFN-24 interface ICs with the same 2.5 V to 5.5 V supply range. Their common package supports a drop-in assessment, but engineers should confirm pin functions, device markings, qualification, and procurement requirements in the TI ordering information before approving a substitution.
What is the best drop-in replacement for PCF8575RGER?
PCF8575RGERG4 is the closest identified alternative because the comparison lists the same 24-pin VQFN package, 16-I/O function, and 2.5 V to 5.5 V supply range. PCF8575CRGER is another same-package family option listed by Texas Instruments. Final substitution approval should include a manufacturer datasheet comparison of pinout, electrical limits, temperature range, and qualification.
When should I choose PCF8575RGER over another I/O expander?
Choose PCF8575RGER when a design needs 16 directly addressable digital I/O lines, an I2C or SMBus connection, an interrupt output, and a compact 24-pin VQFN footprint. The 2.5 V to 5.5 V range also suits both 3.3 V and 5 V systems. Choose another expander only when its I/O count, voltage tolerance, bus speed, or electrical drive requirements provide a clear functional benefit.
Can the PCF8575RGER control LEDs and relays?
The PCF8575RGER can control LEDs directly when the port drive and current limits in the manufacturer electrical characteristics are acceptable. Relays and solenoids normally require transistor, MOSFET, or driver circuitry because their inductive current and flyback voltage can exceed the expander's limits. Add suitable protection and account for inductive transients in the PCB design.
Where can I buy PCF8575RGER and what is its lead time?
Use the Request a Quote form on this page to request PCF8575RGER pricing, stock confirmation, and current lead time for the exact Texas Instruments MPN and RGE package. Lead time can vary with inventory, order quantity, and supply conditions, so obtain a current quotation rather than relying on historical catalog availability. Confirm that the quote identifies PCF8575RGER exactly.
How do I design the I2C connection for the PCF8575RGER?
Connect the PCF8575RGER to the host's I2C or SMBus pins and provide the pull-up arrangement required for the selected bus voltage and speed. Texas Instruments specifies operation up to 400 kHz, so the complete bus must meet that timing target. Keep the route short, keep pull-ups electrically appropriate, and account for the interrupt output's open-drain behavior where applicable.
What are the key specifications of PCF8575RGER that engineers should know?
The key PCF8575RGER specifications are 16 I/O pins, a 2.5 V to 5.5 V supply range, I2C and SMBus support, a maximum listed bus frequency of 400 kHz, an interrupt output, and a 24-pin VQFN RGE package. Texas Instruments specifies an operating temperature range of -40 °C to 85 °C for this orderable part. These parameters define its core interface-expansion capability and package constraints.

엔지니어링 참조 데이터: PCF8575RGER — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose PCF8575RGER when the design needs 16 digital I/O lines, an I2C or SMBus host connection, an interrupt output, and a compact 24-pin VQFN footprint. Its 2.5 V to 5.5 V supply range supports both 3.3 V and 5 V embedded systems, while the -40 °C to 85 °C rating suits industrial and commercial equipment. PCF8575RGERG4 is the closest identified same-package option when its orderable suffix, qualification, marking, and sourcing conditions meet the design requirements. PCF8575CRGER is another Texas Instruments 16-I/O, 400 kHz option in the same 4 mm by 4 mm VQFN format. For both alternatives, verify the complete pin description, electrical characteristics, temperature grade, and lifecycle status against the current manufacturer ordering information. Do not select a different package merely for similar I/O count; a true PCB replacement must preserve the RGE footprint and pin functions.

대체품과의 비교

파라미터 이 제품 PCF8575RGERG4 PCF8575CRGER
Package VQFN-24 (RGE), 4 mm x 4 mm VQFN-24, same package VQFN-24 (RGE), 4 mm x 4 mm
Brand Texas Instruments Texas Instruments Texas Instruments
Number of I/O 16 16 16
Supply Voltage Range 2.5 V to 5.5 V 2.5 V to 5.5 V 2.5 V to 5.5 V
Serial Interface I2C/SMBus I2C/SMBus I2C/SMBus
Maximum Bus Frequency 400 kHz 400 kHz 400 kHz
Interrupt Output Present Present Present

주요 차별점

  • Same-package family option (vs PCF8575RGERG4)
  • Compact 16-I/O expansion (vs PCF8575CRGER)
  • Event-driven host interaction (vs PCF8575CRGER)

설계 노트

Use the Texas Instruments RGE package drawing for land pattern, exposed-pad connection, solder mask, and paste geometry. The PCF8575RGER is a 24-pin VQFN in a 4 mm by 4 mm body, so pad and via dimensions should not be copied from a generic 24-pin QFN. Place the device near the external I/O circuitry and route the I2C and interrupt nets away from switching nodes.

Place the local supply-decoupling capacitor close to the device power and ground pins, and verify the capacitor voltage rating and ESR suitability against the manufacturer's recommended circuit. The supported 2.5 V to 5.5 V range does not eliminate the need for clean power. Confirm that the I2C pull-up voltage and any external pull-up network remain compatible with both the expander and the host controller.

Keep SDA and SCL routes short, use a continuous ground reference, and avoid stubs where practical. The supported bus rate is 400 kHz, but actual timing depends on total bus capacitance, pull-up resistance, clock stretching, and PCB delay. Treat the interrupt output as an open-drain signal when the manufacturer documentation specifies that implementation and size any external pull-up accordingly.

Do not assume every port condition is suitable for direct relay, solenoid, or high-current LED drive. Check the absolute maximum ratings, per-port drive limits, and output transition behavior in the manufacturer datasheet. Use external drivers for inductive loads and provide flyback protection. Also avoid changing an output from input mode without accounting for the PCF8575 quasi-bidirectional port behavior.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

Compliance declarations are not present in the available product-page and distributor excerpts. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals status for the exact orderable MPN with Texas Instruments before release.

관련 검색

PCF8575RGER datasheet PCF8575RGER pinout PCF8575RGER datasheet pdf PCF8575RGER VQFN-24 footprint PCF8575RGER equivalent PCF8575RGER replacement PCF8575RGER vs PCF8575CRGER PCF8575RGER I2C application circuit Texas Instruments PCF8575RGER PCF8575RGER price PCF8575RGER stock PCF8575RGER 400 kHz PCF8575RGER 16 bit I/O expander PCF8575RGER interrupt output PCF8575RGER 2.5V 5.5V

관련 부품 & 용어

Texas Instruments PCF8575RGER PCF8575 PCF8575RGERG4 PCF8575CRGER I/O expander interface IC semiconductor I2C SMBus interrupt output quasi-bidirectional I/O 16-bit parallel port VQFN-24 RGE package QFN family surface mount SMD digital input digital output keypad scanning LED control embedded control industrial control IoT peripheral hub
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기