PI7C9X1172BZHEX - Dual UART I2C/SPI Bridge | Diodes
MPN: PI7C9X1172BZHEX ✓ AktifPI7C9X1172BZHEX Ringkasan
An I2C/SPI-to-UART bridge is an interface IC within the broader serial-interface and communication-controller category. It allows equipment that lacks convenient UART peripherals to exchange serial data through a host-oriented I2C or SPI bus. The PI7C9X1172BZHEX can therefore serve as a protocol-conversion and I/O-expansion element in systems that need to connect serial peripherals, control ports, or communication modules without dedicating multiple UART channels in the main controller.
The key documented characteristics include support for I2C and SPI host-side protocols, two UART channels, operation from 1.8 V, 2.5 V, or 3.3 V supplies, and a compact 32-QFN package. The 5 mm by 5 mm QFN construction supports dense PCB layouts, although its exposed-pad thermal and layout requirements must be implemented according to the manufacturer's package information. Because the package has 32 terminals, its footprint requires careful fanout routing between the fine-pitch perimeter pads and the exposed thermal pad.
The device is positioned for embedded control, industrial communication, instrumentation, and equipment-connection applications where an existing I2C or SPI processor interface must provide access to two UART channels. The selectable 1.8 V, 2.5 V, and 3.3 V operating options also permit integration with common low-voltage digital systems. Exact UART baud-rate limits, I2C/SPI timing, logic thresholds, electrical characteristics, and channel-configuration details should be confirmed in the manufacturer datasheet before a production design is released.
Typical implementations place the bridge beside the controlled peripheral and connect the host controller through I2C or SPI. Software then performs protocol translation while the UART side connects to the target equipment. A key design consideration is matching the bridge's supply voltage, host-bus logic levels, pin multiplexing, and UART signal requirements to the connected devices. Decoupling and exposed-pad handling should follow the manufacturer's recommended layout to limit supply disturbance and maintain reliable operation in compact assemblies.
This product page consolidates the confirmed interface function, supply options, package details, sourcing information, and replacement analysis into an engineering-focused reference. The PI7C9X1172BZHEX is most appropriate when a design requires a dedicated I2C/SPI-to-dual-UART bridge in a 32-QFN footprint. Production adoption should include verification of the complete electrical specification, pin assignment, timing limits, and package drawing against the current manufacturer documentation.
Alternatif penggantian untuk PI7C9X1172BZHEX — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Tidak ada alternatif pengganti yang tersedia untuk produk ini.
Permintaan AlternatifPI7C9X1172BZHEX Rating Maksimal & Karakteristik Listrik
| Device Type | I2C/SPI to dual-channel UART bridge |
| Host-Side Protocols | I2C and SPI |
| UART Channel Count | 2 channels |
| Supply Voltage Option 1 | 1.8 V |
| Supply Voltage Option 2 | 2.5 V |
| Supply Voltage Option 3 | 3.3 V |
| Package Type | 32-QFN |
| Package Dimensions | 5 mm x 5 mm |
| Device Classification | UART interface IC |
| Manufacturer | Diodes Incorporated |
PI7C9X1172BZHEX 5 mm x 5 mm Diamant Konfigurasi Panduan
Konfigurasi pin untuk PI7C9X1172BZHEX (5 mm x 5 mm pakai pakai). Alat kuasa ini memiliki terminal gate, drain, dan sumber. Untuk pakai pakai yang tak polar, lihat datasheet produsen untuk orientasi dan detil footprint pin 1 yang pasti. Aplikasi umum termasuk desain penolong daya, menggerakkan motor, dan mengalihkan muatan.
Tidak ada data diatribut pin yang tersedia untuk PI7C9X1172BZHEX.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
PI7C9X1172BZHEX cocok untuk 6 aplikasis: Embedded Control with Dual UART Peripherals, Industrial Sensor and Controller Networking, Instrumentation with Multiple Serial Devices, Communication Adapter and Protocol Converter, Portable and Battery-Powered Equipment, Data Acquisition Front End.
Embedded Control with Dual UART Peripherals
The PI7C9X1172BZHEX fits systems whose main controller exposes I2C or SPI but must also communicate with two UART-based peripherals. The host-side bridge connection consolidates both UART channels behind a serial processor interface, reducing the need for dedicated UART hardware in the primary controller. Its documented 1.8 V, 2.5 V, and 3.3 V supply options support common low-voltage embedded platforms. During implementation, confirm the host-bus timing, configuration method, UART baud-rate limits, and exact 32-QFN pin assignments before releasing the PCB.
Industrial Sensor and Controller Networking
The PI7C9X1172BZHEX can connect two UART-oriented industrial sensors or controllers to an I2C- or SPI-capable supervisory processor. This arrangement is useful when the supervisory controller handles higher-level sequencing while external modules retain conventional UART command interfaces. The bridge's two-channel structure avoids assigning separate processor UART resources to each module. For industrial equipment, verify electrical levels, isolation requirements, surge exposure, and timing margins against the exact manufacturer specification.
Instrumentation with Multiple Serial Devices
Test and measurement instruments often combine an I2C or SPI control processor with legacy UART instruments. The PI7C9X1172BZHEX provides a protocol-conversion path for two UART devices while retaining the processor's preferred host-side bus. Its compact 5 mm by 5 mm 32-QFN package helps conserve board area in dense instrumentation. Designers should confirm supported baud rates, parity and data-bit configurations, and host command timing, then validate protocol translation with representative peripherals.
Communication Adapter and Protocol Converter
The PI7C9X1172BZHEX can serve as the interface-conversion element in a communication adapter that accepts I2C or SPI commands and forwards them to two UART endpoints. This topology is useful for retrofitting UART-based modules into I2C- or SPI-oriented control ecosystems without redesigning the endpoint firmware. The three documented supply options, 1.8 V, 2.5 V, and 3.3 V, permit use across different logic domains, subject to confirming compatible voltage levels and the manufacturer's operating limits.
Portable and Battery-Powered Equipment
In portable equipment, a system processor may use I2C or SPI internally while a few external modules still require UART links. The PI7C9X1172BZHEX adds those links through a compact 5 mm by 5 mm 32-QFN device rather than requiring a larger external bridge. Its 1.8 V supply option is relevant to low-voltage portable designs. Battery-operated implementations should still evaluate idle current, active current, sleep behavior, and regulator headroom using the exact manufacturer electrical characteristics.
Data Acquisition Front End
A data-acquisition controller using I2C or SPI for configuration can use the PI7C9X1172BZHEX to connect two UART-facing measurement or communication modules. The dual-channel bridge reduces host pin count and centralizes protocol conversion in a dedicated interface IC. Because measurement accuracy can be affected by supply noise and timing margins, place the bridge with appropriate decoupling, route UART signals away from sensitive analog nets, and confirm acquisition-device baud-rate and framing requirements.
Data referensi engineering untuk PI7C9X1172BZHEX — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini |
|---|---|
| Brand | Diodes Incorporated |
| Package | 32-QFN (5x5 mm) |
| Device Type | I2C/SPI to dual-channel UART bridge |
| Host-Side Protocols | I2C and SPI |
| UART Channel Count | 2 channels |
| Supply Voltage Options | 1.8 V, 2.5 V, 3.3 V |
| Package Dimensions | 5 mm x 5 mm |
| Mounting Technology | Surface-mount QFN |
| Related 28-TSSOP Version | Not applicable; PI7C9X1172BZHEX uses 32-QFN |
Diferensiator Kunci
- Dedicated dual-UART conversion behind one host interface (vsSoftware-UART implementation)
- Three low-voltage supply options (vsPI7C9X1172BLE)
- Different package choices for different PCB constraints (vsPI7C9X1172BLE)
Catatan Desain
Design the 32-QFN footprint directly from the PI7C9X1172BZHEX package drawing rather than copying a generic QFN-32 land pattern. Confirm pad length, pad width, pitch, exposed-pad dimensions, solder-mask clearance, and paste stencil geometry. Connect the exposed pad to the intended ground or supply plane only as specified by the manufacturer, and place via arrays and decoupling capacitors in accordance with the recommended layout.
Provide a local supply rail and place the required bypass capacitor adjacent to the device's supply and ground terminals. Keep the I2C or SPI host traces and UART signals away from noisy switching-regulator paths. The bridge supports 1.8 V, 2.5 V, and 3.3 V operation, but the selected supply must also satisfy the connected devices' logic levels. Confirm peak current and startup behavior in the manufacturer datasheet before setting regulator margin.
Do not substitute a similarly named part solely because it performs I2C/SPI-to-UART conversion. The PI7C9X1172BZHEX uses a 32-QFN package, whereas the listed PI7C9X1172BLE uses a 28-TSSOP package and therefore cannot replace it without PCB changes. Verify the exact pin assignment, protocol mode, configuration method, address allocation, and timing behavior for the replacement before approving it for production.
Treat I2C, SPI, and UART routing as separate interface groups during PCB planning. Keep the I2C bus away from long, unterminated SPI traces and noisy UART edges, observe the bus timing required by the selected host speed, and provide the pull-ups and termination arrangements prescribed for each interface. Validate the assembled design with rise-time, timing-margin, and communication-error measurements across all three supported supply voltages.
Informasi Konformitas
The available product listings confirm manufacturer, interface function, supply options, and package, but do not state RoHS, REACH, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not indicated for this general-purpose interface device.