PIC17C756AT-33I/L - 33MHz 8-Bit OTP MCU, 32KB, 50 I/O | Microchip
MPN: PIC17C756AT-33I/L ⚠ Waktu Beli TerakhirPIC17C756AT-33I/L Ringkasan
A microcontroller (MCU) is an integrated circuit that combines a CPU core, non-volatile program memory, working RAM, and a set of on-chip peripherals behind a unified instruction set, allowing a single chip to replace dozens of discrete logic devices. The PIC17C family sits between Microchip's baseline PIC16C5X/PIC16CXX devices and the later PIC18F parts, adding a 16-bit-wide instruction word (which yields 32KB of code space from a single OTP array) while keeping an 8-bit data path and only 58 single-word instructions to learn. This positioning explains why PIC17C756A-series parts are still specified in long-lifecycle industrial designs even after the family was officially replaced by the PIC18F6520.
Key features of the PIC17C756AT-33I/L include 50 programmable digital I/O lines, 12 channels of 10-bit Analog-to-Digital conversion, a single-cycle 8-bit hardware multiplier, dual hardware PWM/Capture/Compare modules, an asynchronous serial port (USART), a synchronous serial port (SSP) for SPI/I2C, and a wide 4.5V to 5.5V supply range suited to industrial 5V rails. The /L suffix denotes the 68-pin PLCC (Plastic Leaded Chip Carrier, J-leaded, 24.23 x 24.23 mm) surface-mount package, and the /I industrial temperature grade spans -40C to +85C.
Architecturally, the PIC17C756A uses a RISC-style Harvard bus with separate program and data paths, an internal instruction pipeline, and an 8-level deep hardware stack, which together enable deterministic 121 ns instruction cycles except for two-cycle program branches and table reads/writes. The on-chip peripherals are mapped into the SFR space, and the 10-bit ADC includes dedicated sample-and-hold and programmable acquisition timing.
Typical applications include industrial automation controllers, motor control front-ends, instrumentation front panels, automotive body electronics (where the part was historically qualified in non-AEC-Q100 designs), HVAC control boards, and legacy embedded products that were designed around the PIC17C family before migrating to PIC18F. The combination of 50 I/O, 12 ADC channels, and a 5V-tolerant architecture makes it a frequent choice for sensor aggregation nodes.
When designing with this part, allow at least a 2-layer board with a solid ground pour under the PLCC footprint and place a 0.1 uF decoupling capacitor on every VDD/VSS pair. Because the device is OTP rather than flash, the firmware must be fully validated before programming - in-circuit reprogramming is not possible.
This page synthesizes current distributor stock, parametric cross-references, and application guidance for engineers who still need to source or design around the PIC17C756A family.
Alternatif penggantian untuk PIC17C756AT-33I/L — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC17C756AT-33I/L (sama faktor bentuk dan footprint) — berbeda di dalam Core Architecture, Package, Data Bus Width, Program Memory Type, Operating Temperature.
PIC17C756A-33I/L
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC17C756AT-33I/L024
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC17C756AT-33I/CL
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC17C756AT-33E/L
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC17C756AT-33I/L
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC17C756AT-33I/L Rating Maksimal & Karakteristik Listrik
| Core Architecture | PIC17C, 8-bit RISC (Harvard) |
| Instruction Word Width | 16-bit |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 32 KB (16K x 16) |
| Data RAM | 902 bytes |
| Frekuensi Bawah Maximum | 33 MHz |
| Instruction Cycle Time | 121 ns (single-cycle, except branches/table reads) |
| Throughput | 8.25 MIPS |
| Supply Voltage (VDD) | 4.5 V to 5.5 V |
| I/O Pins | 50 programmable digital I/O |
| ADC | 12 channels x 10-bit |
| Hardware Multiplier | 8 x 8 single-cycle |
| PWM / CCP Modules | Dual Capture/Compare/PWM |
| Serial Interfaces | USART (async) + SSP (SPI / I2C) |
| Paket | 68-pin PLCC (LCC-68), J-lead, 24.23 x 24.23 mm |
| Rentang Suhu Kerja | -40 C to +85 C (Industrial / 'I' grade) |
| Tipe Mounting | Surface Mount (PLCC socket compatible) |
| Status RoHS | Not RoHS compliant (PLCC with matte-tin/lead finish historically) |
| Instruction Set | 58 single-word instructions |
Konfigurasi Pin PIC17C756AT-33I/L
| Pin produk 1 | MCLR — Master Clear (Reset) input, active low |
| Pin produk 2 | OSC1 — Crystal oscillator / clock input |
| Pin produk 3 | OSC2 — Crystal oscillator output |
| Pin produk 4 | RA0/AN0 — Port A bit 0 / Analog input 0 |
| Pin produk 5 | RA1/AN1 — Port A bit 1 / Analog input 1 |
| Pin produk 6 | RA2/AN2 — Port A bit 2 / Analog input 2 |
| Pin produk 7 | RA3/AN3 — Port A bit 3 / Analog input 3 |
| Pin produk 8 | RA4/AN4 — Port A bit 4 / Analog input 4 |
| Pin produk 9 | RA5/AN5 — Port A bit 5 / Analog input 5 |
| Pin produk 10 | AVDD — Analog VDD supply |
| Pin produk 11 | AVSS — Analog VSS ground |
| Pin produk 12 | VSS — Digital ground |
| Pin produk 13 | VDD — Digital supply |
| Pin produk 14 | RB0/INT — Port B bit 0 / External interrupt |
| Pin produk 15 | RB1 — Port B bit 1 |
| Pin produk 16 | RB2 — Port B bit 2 |
| Pin produk 17 | RB3 — Port B bit 3 |
| Pin produk 18 | RB4 — Port B bit 4 |
| Pin produk 19 | RB5 — Port B bit 5 |
| Pin produk 20 | RB6 — Port B bit 6 |
| Pin produk 21 | RB7 — Port B bit 7 |
| Pin produk 22 | VSS — Digital ground |
| Pin produk 23 | VDD — Digital supply |
| Pin produk 24 | RC0 — Port C bit 0 / CCP1 |
| Pin produk 25 | RC1 — Port C bit 1 / CCP2 |
| Pin produk 26 | RC2 — Port C bit 2 |
| Pin produk 27 | RC3 — Port C bit 3 / SCL (SSP) |
| Pin produk 28 | RC4 — Port C bit 4 / SDA (SSP) |
| Pin produk 29 | RC5 — Port C bit 5 / SDO (SSP) |
| Pin produk 30 | RC6 — Port C bit 6 / TX (USART) |
| Pin produk 31 | RC7 — Port C bit 7 / RX (USART) |
| Pin produk 32 | VSS — Digital ground |
| Pin produk 33 | VDD — Digital supply |
| Pin produk 34 | RD0 — Port D bit 0 |
| Pin produk 35 | RD1 — Port D bit 1 |
| Pin produk 36 | RD2 — Port D bit 2 |
| Pin produk 37 | RD3 — Port D bit 3 |
| Pin produk 38 | RD4 — Port D bit 4 |
| Pin produk 39 | RD5 — Port D bit 5 |
| Pin produk 40 | RD6 — Port D bit 6 |
| Pin produk 41 | RD7 — Port D bit 7 |
| Pin produk 42 | VSS — Digital ground |
| Pin produk 43 | VDD — Digital supply |
| Pin produk 44 | RE0/AN6 — Port E bit 0 / Analog input 6 |
| Pin produk 45 | RE1/AN7 — Port E bit 1 / Analog input 7 |
| Pin produk 46 | RE2/AN8 — Port E bit 2 / Analog input 8 |
| Pin produk 47 | RE3/AN9 — Port E bit 3 / Analog input 9 |
| Pin produk 48 | RE4/AN10 — Port E bit 4 / Analog input 10 |
| Pin produk 49 | RE5/AN11 — Port E bit 5 / Analog input 11 |
| Pin produk 50 | VSS — Digital ground |
| Pin produk 51 | VDD — Digital supply |
| Pin produk 52 | RF0 — Port F bit 0 |
| Pin produk 53 | RF1 — Port F bit 1 |
| Pin produk 54 | RF2 — Port F bit 2 |
| Pin produk 55 | RF3 — Port F bit 3 |
| Pin produk 56 | RF4 — Port F bit 4 |
| Pin produk 57 | RF5 — Port F bit 5 |
| Pin produk 58 | RF6 — Port F bit 6 |
| Pin produk 59 | RF7 — Port F bit 7 |
| Pin produk 60 | VSS — Digital ground |
| Pin produk 61 | VDD — Digital supply |
| Pin produk 62 | RG0 — Port G bit 0 |
| Pin produk 63 | RG1 — Port G bit 1 |
| Pin produk 64 | RG2 — Port G bit 2 |
| Pin produk 65 | RG3 — Port G bit 3 |
| Pin produk 66 | RG4 — Port G bit 4 |
| Pin produk 67 | T0CKI — Timer 0 clock input |
| Pin produk 68 | NC — Not connected (per datasheet) |
Aplikasi Umum
PIC17C756AT-33I/L cocok untuk 7 aplikasis: Industrial Automation Controllers, Motor Control Front-End, Instrumentation Front Panels, HVAC Control Boards, Sensor Aggregation Nodes, Legacy Embedded Maintenance, Automotive Body Electronics (Legacy).
Industrial Automation Controllers
The PIC17C756AT-33I/L's 50 programmable I/O lines, 12-channel 10-bit ADC, and dual Capture/Compare/PWM peripherals make it well-suited to industrial automation controllers that aggregate sensors and drive actuators from a single 5V rail. Its 8.25 MIPS throughput and 121 ns instruction cycle are sufficient for PID loops sampled at sub-millisecond rates, while the 32 KB OTP code space accommodates ladder-logic-equivalent C state machines. The 4.5V to 5.5V supply range aligns with legacy 24V industrial backplanes that regulate down to 5V.
Direkomendasikan
Motor Control Front-End
With dual PWM/CCP modules, an 8-bit hardware multiplier (single-cycle), and the 10-bit ADC's 12 analog inputs, the PIC17C756AT-33I/L can implement sensored or sensorless motor control for low- to mid-power BLDC, brushed DC, and stepper drives. The 33 MHz / 8.25 MIPS throughput supports trapezoidal commutation loops up to tens of kHz. Engineers should note that for higher-performance vector control, migration to a dsPIC33 part (e.g., DSPIC33EP64MC504) is recommended.
Direkomendasikan
Instrumentation Front Panels
The PIC17C756AT-33I/L integrates the CPU, code memory, RAM, ADC, and serial interfaces required to drive instrumentation front panels that combine a 7-segment or character-LCD display with pushbuttons and analog sensor inputs. Its USART (async) and SSP (SPI/I2C) peripherals simplify interfacing to backplane MCUs, display controllers, and digital sensors. The wide 5V tolerance and industrial -40C to +85C range suit benchtop and rack-mounted test equipment.
Direkomendasikan
HVAC Control Boards
HVAC control boards typically require multiple analog inputs (temperature, pressure, humidity transducers), digital outputs for relays and triac drivers, and serial communications for building-automation backbones - exactly the role profile of the PIC17C756AT-33I/L. Its 12 ADC channels cover multiple thermistor/sensor inputs, while 50 I/O drive fans, dampers, and triacs. The 5V operation and -40C to +85C industrial range match typical equipment-room environments.
Direkomendasikan
Sensor Aggregation Nodes
As a sensor aggregation node in legacy distributed I/O systems, the PIC17C756AT-33I/L reads multiple analog and digital sensors, performs local averaging/threshold processing in its 902-byte RAM, and reports results via USART or SSP. The 32 KB OTP code space supports simple MODBUS-RTU or vendor-proprietary protocols. The part's deterministic 121 ns instruction cycle makes it well-suited to time-stamped data acquisition where jitter must be minimized.
Direkomendasikan
Legacy Embedded Maintenance
The PIC17C756AT-33I/L remains in use for service and spare-part replacement of fielded industrial and medical equipment that was designed around the PIC17C family in the late 1990s. With Microchip now in last-time-buy for this part, EOL planning requires identifying pin-compatible variants (PIC17C756AT-33E/L for higher temp, PIC17C756A-33I/L for non-T&R) and modern replacements (PIC18F6520) for board redesigns. Functional testing must verify ADC linearity and I/O timing against the original design's qualification data.
Direkomendasikan
Automotive Body Electronics (Legacy)
Some legacy automotive body-electronics modules were designed around the PIC17C756A in the late 1990s and early 2000s. While the part is not AEC-Q100 qualified, it was deployed in cabin-mounted modules with relaxed thermal and qualification requirements. The 50 I/O and 12 ADC channels support multi-zone lighting control, seat/mirror positioning, and HVAC blend-door control. New automotive designs must use AEC-Q100-qualified parts such as PIC18F46K22 or dsPIC33EV parts.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC17C756AT-33I/L — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC17C756A-33I/L | PIC17C756AT-33I/L024 | PIC17C756AT-33I/CL | PIC17C756AT-33E/L |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 68-pin PLCC (LCC-68) | 68-pin PLCC (LCC-68) - same | 68-pin PLCC (LCC-68) - same | 68-pin PLCC (LCC-68), ceramic windowed - same | 68-pin PLCC (LCC-68) - same |
| Program Memory | 32 KB (16K x 16) OTP | 32 KB OTP - same | 32 KB OTP - same | 32 KB EPROM (windowed) | 32 KB OTP - same |
| RAM | 902 bytes | 902 bytes - same | 902 bytes - same | 902 bytes - same | 902 bytes - same |
| Maximum Clock | 33 MHz | 33 MHz - same | 33 MHz - same | 33 MHz - same | 33 MHz - same |
| I/O Pins | 50 | 50 - same | 50 - same | 50 - same | 50 - same |
| ADC Channels | 12 x 10-bit | 12 x 10-bit - same | 12 x 10-bit - same | 12 x 10-bit - same | 12 x 10-bit - same |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C - same | -40C to +85C - same | -40C to +85C - same | -40C to +125C (Extended) |
| Memory Type | OTP (one-time programmable) | OTP - same | OTP - same | Windowed EPROM (UV-erasable, prototype/debug) | OTP - same |
Diferensiator Kunci
- Industrial temperature range with same silicon as E/L variant (vsPIC17C756AT-33E/L)
- OTP rather than windowed EPROM (vsPIC17C756AT-33I/CL)
- Pin-compatible with the broader PIC17C family migration path (vsPIC18F6520)
Catatan Desain
Decouple every VDD/VSS pair on the 68-pin PLCC with a 100 nF X7R ceramic placed as close to the package pin as possible; add a single 10 uF bulk tantalum or aluminum-polymer capacitor at the board's 5V entry. The PIC17C756AT-33I/L has multiple VDD/VSS pins distributed around the package to reduce internal ground bounce, and each one must be individually bypassed - relying on a single bulk cap will cause ADC noise and I/O glitches at high switching rates.
Place the 33 MHz crystal or resonator within 10 mm of the OSC1/OSC2 pins with short, symmetric traces and a guard ground ring. Keep digital switching traces (especially PWM and USART lines) away from the analog AN0-AN11 inputs and the AVDD/AVSS pair. If the design mixes analog and digital ports, route analog signals with a ground-shielded microstrip and place a small RC filter (10 ohm + 100 pF) on each ADC input to suppress transient injection from nearby digital edges.
Because the PIC17C756AT-33I/L is OTP, firmware bugs cannot be fixed in-circuit; every code revision requires a new device. Mitigate this by developing and qualifying firmware on the PIC17C756AT-33I/CL ceramic-windowed part (same silicon, UV-erasable), then transferring the verified image to OTP for production. Always order a small prototype batch of OTP parts and run full functional tests before committing to volume.
Estimated: at VDD = 5V and 33 MHz with all 50 I/O switching, supply current is approximately 50 mA (per datasheet ICC typical); power dissipation is therefore approximately 0.25 W, well within the 68-PLCC's thermal envelope (theta_JA around 50 C/W). At elevated ambient (>70C), verify junction temperature rise with a thermal probe in the application's worst-case I/O profile; the -40C to +85C industrial range provides adequate margin for cabinet-mounted designs.
Informasi Konformitas
68-pin PLCC package historically uses SnPb (tin-lead) finish and is not RoHS compliant; PIC17C756A family is not AEC-Q100 qualified. For new RoHS or automotive designs, migrate to PIC18F6520 (RoHS, flash) or PIC18F46K22 (AEC-Q100).
