PIC17C756AT-33I/L - 33MHz 8-Bit OTP MCU, 32KB, 50 I/O | Microchip
Артикул: PIC17C756AT-33I/L ⚠ Последняя закупка| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.85 | $168,50 |
| 100 | $15.2 | $1.520,00 |
| 500 | $13.75 | $6.875,00 |
| 1.000 | $12.4 | $12.400,00 |
PIC17C756AT-33I/L Обзор
A microcontroller (MCU) is an integrated circuit that combines a CPU core, non-volatile program memory, working RAM, and a set of on-chip peripherals behind a unified instruction set, allowing a single chip to replace dozens of discrete logic devices. The PIC17C family sits between Microchip's baseline PIC16C5X/PIC16CXX devices and the later PIC18F parts, adding a 16-bit-wide instruction word (which yields 32KB of code space from a single OTP array) while keeping an 8-bit data path and only 58 single-word instructions to learn. This positioning explains why PIC17C756A-series parts are still specified in long-lifecycle industrial designs even after the family was officially replaced by the PIC18F6520.
Key features of the PIC17C756AT-33I/L include 50 programmable digital I/O lines, 12 channels of 10-bit Analog-to-Digital conversion, a single-cycle 8-bit hardware multiplier, dual hardware PWM/Capture/Compare modules, an asynchronous serial port (USART), a synchronous serial port (SSP) for SPI/I2C, and a wide 4.5V to 5.5V supply range suited to industrial 5V rails. The /L suffix denotes the 68-pin PLCC (Plastic Leaded Chip Carrier, J-leaded, 24.23 x 24.23 mm) surface-mount package, and the /I industrial temperature grade spans -40C to +85C.
Architecturally, the PIC17C756A uses a RISC-style Harvard bus with separate program and data paths, an internal instruction pipeline, and an 8-level deep hardware stack, which together enable deterministic 121 ns instruction cycles except for two-cycle program branches and table reads/writes. The on-chip peripherals are mapped into the SFR space, and the 10-bit ADC includes dedicated sample-and-hold and programmable acquisition timing.
Typical applications include industrial automation controllers, motor control front-ends, instrumentation front panels, automotive body electronics (where the part was historically qualified in non-AEC-Q100 designs), HVAC control boards, and legacy embedded products that were designed around the PIC17C family before migrating to PIC18F. The combination of 50 I/O, 12 ADC channels, and a 5V-tolerant architecture makes it a frequent choice for sensor aggregation nodes.
When designing with this part, allow at least a 2-layer board with a solid ground pour under the PLCC footprint and place a 0.1 uF decoupling capacitor on every VDD/VSS pair. Because the device is OTP rather than flash, the firmware must be fully validated before programming - in-circuit reprogramming is not possible.
This page synthesizes current distributor stock, parametric cross-references, and application guidance for engineers who still need to source or design around the PIC17C756A family.
Аналоги без доработки для PIC17C756AT-33I/L — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC17C756AT-33I/L (тот же форм-фактор и посадочное место) — отличается по Core Architecture, Package, Data Bus Width, Program Memory Type, Operating Temperature.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC17C756A-33I/L
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC17C756AT-33I/L024
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC17C756AT-33I/CL
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC17C756AT-33E/L
✅ Прямая замена✓ В наличии
$10.4 / шт.
Открыть даташит →PIC17C756AT-33I/L
✅ Прямая замена✓ В наличии
$12.4 / шт.
Открыть даташит →PIC17C756AT-33I/L Максимальные параметры и электрические характеристики
| Core Architecture | PIC17C, 8-bit RISC (Harvard) |
| Instruction Word Width | 16-bit |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 32 KB (16K x 16) |
| Data RAM | 902 bytes |
| Максимальная тактовая частота | 33 MHz |
| Instruction Cycle Time | 121 ns (single-cycle, except branches/table reads) |
| Throughput | 8.25 MIPS |
| Supply Voltage (VDD) | 4.5 V to 5.5 V |
| I/O Pins | 50 programmable digital I/O |
| ADC | 12 channels x 10-bit |
| Hardware Multiplier | 8 x 8 single-cycle |
| PWM / CCP Modules | Dual Capture/Compare/PWM |
| Serial Interfaces | USART (async) + SSP (SPI / I2C) |
| Корпус | 68-pin PLCC (LCC-68), J-lead, 24.23 x 24.23 mm |
| Диапазон рабочих температур | -40 C to +85 C (Industrial / 'I' grade) |
| Тип монтажа | Surface Mount (PLCC socket compatible) |
| Статус RoHS | Not RoHS compliant (PLCC with matte-tin/lead finish historically) |
| Instruction Set | 58 single-word instructions |
Конфигурация выводов PIC17C756AT-33I/L
| Контакт 1 | MCLR — Master Clear (Reset) input, active low |
| Контакт 2 | OSC1 — Crystal oscillator / clock input |
| Контакт 3 | OSC2 — Crystal oscillator output |
| Контакт 4 | RA0/AN0 — Port A bit 0 / Analog input 0 |
| Контакт 5 | RA1/AN1 — Port A bit 1 / Analog input 1 |
| Контакт 6 | RA2/AN2 — Port A bit 2 / Analog input 2 |
| Контакт 7 | RA3/AN3 — Port A bit 3 / Analog input 3 |
| Контакт 8 | RA4/AN4 — Port A bit 4 / Analog input 4 |
| Контакт 9 | RA5/AN5 — Port A bit 5 / Analog input 5 |
| Контакт 10 | AVDD — Analog VDD supply |
| Контакт 11 | AVSS — Analog VSS ground |
| Контакт 12 | VSS — Digital ground |
| Контакт 13 | VDD — Digital supply |
| Контакт 14 | RB0/INT — Port B bit 0 / External interrupt |
| Контакт 15 | RB1 — Port B bit 1 |
| Контакт 16 | RB2 — Port B bit 2 |
| Контакт 17 | RB3 — Port B bit 3 |
| Контакт 18 | RB4 — Port B bit 4 |
| Контакт 19 | RB5 — Port B bit 5 |
| Контакт 20 | RB6 — Port B bit 6 |
| Контакт 21 | RB7 — Port B bit 7 |
| Контакт 22 | VSS — Digital ground |
| Контакт 23 | VDD — Digital supply |
| Контакт 24 | RC0 — Port C bit 0 / CCP1 |
| Контакт 25 | RC1 — Port C bit 1 / CCP2 |
| Контакт 26 | RC2 — Port C bit 2 |
| Контакт 27 | RC3 — Port C bit 3 / SCL (SSP) |
| Контакт 28 | RC4 — Port C bit 4 / SDA (SSP) |
| Контакт 29 | RC5 — Port C bit 5 / SDO (SSP) |
| Контакт 30 | RC6 — Port C bit 6 / TX (USART) |
| Контакт 31 | RC7 — Port C bit 7 / RX (USART) |
| Контакт 32 | VSS — Digital ground |
| Контакт 33 | VDD — Digital supply |
| Контакт 34 | RD0 — Port D bit 0 |
| Контакт 35 | RD1 — Port D bit 1 |
| Контакт 36 | RD2 — Port D bit 2 |
| Контакт 37 | RD3 — Port D bit 3 |
| Контакт 38 | RD4 — Port D bit 4 |
| Контакт 39 | RD5 — Port D bit 5 |
| Контакт 40 | RD6 — Port D bit 6 |
| Контакт 41 | RD7 — Port D bit 7 |
| Контакт 42 | VSS — Digital ground |
| Контакт 43 | VDD — Digital supply |
| Контакт 44 | RE0/AN6 — Port E bit 0 / Analog input 6 |
| Контакт 45 | RE1/AN7 — Port E bit 1 / Analog input 7 |
| Контакт 46 | RE2/AN8 — Port E bit 2 / Analog input 8 |
| Контакт 47 | RE3/AN9 — Port E bit 3 / Analog input 9 |
| Контакт 48 | RE4/AN10 — Port E bit 4 / Analog input 10 |
| Контакт 49 | RE5/AN11 — Port E bit 5 / Analog input 11 |
| Контакт 50 | VSS — Digital ground |
| Контакт 51 | VDD — Digital supply |
| Контакт 52 | RF0 — Port F bit 0 |
| Контакт 53 | RF1 — Port F bit 1 |
| Контакт 54 | RF2 — Port F bit 2 |
| Контакт 55 | RF3 — Port F bit 3 |
| Контакт 56 | RF4 — Port F bit 4 |
| Контакт 57 | RF5 — Port F bit 5 |
| Контакт 58 | RF6 — Port F bit 6 |
| Контакт 59 | RF7 — Port F bit 7 |
| Контакт 60 | VSS — Digital ground |
| Контакт 61 | VDD — Digital supply |
| Контакт 62 | RG0 — Port G bit 0 |
| Контакт 63 | RG1 — Port G bit 1 |
| Контакт 64 | RG2 — Port G bit 2 |
| Контакт 65 | RG3 — Port G bit 3 |
| Контакт 66 | RG4 — Port G bit 4 |
| Контакт 67 | T0CKI — Timer 0 clock input |
| Контакт 68 | NC — Not connected (per datasheet) |
Типичное применение
PIC17C756AT-33I/L подходит для 7 применениеs: Industrial Automation Controllers, Motor Control Front-End, Instrumentation Front Panels, HVAC Control Boards, Sensor Aggregation Nodes, Legacy Embedded Maintenance, Automotive Body Electronics (Legacy).
Industrial Automation Controllers
The PIC17C756AT-33I/L's 50 programmable I/O lines, 12-channel 10-bit ADC, and dual Capture/Compare/PWM peripherals make it well-suited to industrial automation controllers that aggregate sensors and drive actuators from a single 5V rail. Its 8.25 MIPS throughput and 121 ns instruction cycle are sufficient for PID loops sampled at sub-millisecond rates, while the 32 KB OTP code space accommodates ladder-logic-equivalent C state machines. The 4.5V to 5.5V supply range aligns with legacy 24V industrial backplanes that regulate down to 5V.
Рекомендуется
Motor Control Front-End
With dual PWM/CCP modules, an 8-bit hardware multiplier (single-cycle), and the 10-bit ADC's 12 analog inputs, the PIC17C756AT-33I/L can implement sensored or sensorless motor control for low- to mid-power BLDC, brushed DC, and stepper drives. The 33 MHz / 8.25 MIPS throughput supports trapezoidal commutation loops up to tens of kHz. Engineers should note that for higher-performance vector control, migration to a dsPIC33 part (e.g., DSPIC33EP64MC504) is recommended.
Рекомендуется
Instrumentation Front Panels
The PIC17C756AT-33I/L integrates the CPU, code memory, RAM, ADC, and serial interfaces required to drive instrumentation front panels that combine a 7-segment or character-LCD display with pushbuttons and analog sensor inputs. Its USART (async) and SSP (SPI/I2C) peripherals simplify interfacing to backplane MCUs, display controllers, and digital sensors. The wide 5V tolerance and industrial -40C to +85C range suit benchtop and rack-mounted test equipment.
Рекомендуется
HVAC Control Boards
HVAC control boards typically require multiple analog inputs (temperature, pressure, humidity transducers), digital outputs for relays and triac drivers, and serial communications for building-automation backbones - exactly the role profile of the PIC17C756AT-33I/L. Its 12 ADC channels cover multiple thermistor/sensor inputs, while 50 I/O drive fans, dampers, and triacs. The 5V operation and -40C to +85C industrial range match typical equipment-room environments.
Рекомендуется
Sensor Aggregation Nodes
As a sensor aggregation node in legacy distributed I/O systems, the PIC17C756AT-33I/L reads multiple analog and digital sensors, performs local averaging/threshold processing in its 902-byte RAM, and reports results via USART or SSP. The 32 KB OTP code space supports simple MODBUS-RTU or vendor-proprietary protocols. The part's deterministic 121 ns instruction cycle makes it well-suited to time-stamped data acquisition where jitter must be minimized.
Рекомендуется
Legacy Embedded Maintenance
The PIC17C756AT-33I/L remains in use for service and spare-part replacement of fielded industrial and medical equipment that was designed around the PIC17C family in the late 1990s. With Microchip now in last-time-buy for this part, EOL planning requires identifying pin-compatible variants (PIC17C756AT-33E/L for higher temp, PIC17C756A-33I/L for non-T&R) and modern replacements (PIC18F6520) for board redesigns. Functional testing must verify ADC linearity and I/O timing against the original design's qualification data.
Рекомендуется
Automotive Body Electronics (Legacy)
Some legacy automotive body-electronics modules were designed around the PIC17C756A in the late 1990s and early 2000s. While the part is not AEC-Q100 qualified, it was deployed in cabin-mounted modules with relaxed thermal and qualification requirements. The 50 I/O and 12 ADC channels support multi-zone lighting control, seat/mirror positioning, and HVAC blend-door control. New automotive designs must use AEC-Q100-qualified parts such as PIC18F46K22 or dsPIC33EV parts.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC17C756AT-33I/L — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC17C756A-33I/L | PIC17C756AT-33I/L024 | PIC17C756AT-33I/CL | PIC17C756AT-33E/L |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 68-pin PLCC (LCC-68) | 68-pin PLCC (LCC-68) - same | 68-pin PLCC (LCC-68) - same | 68-pin PLCC (LCC-68), ceramic windowed - same | 68-pin PLCC (LCC-68) - same |
| Program Memory | 32 KB (16K x 16) OTP | 32 KB OTP - same | 32 KB OTP - same | 32 KB EPROM (windowed) | 32 KB OTP - same |
| RAM | 902 bytes | 902 bytes - same | 902 bytes - same | 902 bytes - same | 902 bytes - same |
| Maximum Clock | 33 MHz | 33 MHz - same | 33 MHz - same | 33 MHz - same | 33 MHz - same |
| I/O Pins | 50 | 50 - same | 50 - same | 50 - same | 50 - same |
| ADC Channels | 12 x 10-bit | 12 x 10-bit - same | 12 x 10-bit - same | 12 x 10-bit - same | 12 x 10-bit - same |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C - same | -40C to +85C - same | -40C to +85C - same | -40C to +125C (Extended) |
| Memory Type | OTP (one-time programmable) | OTP - same | OTP - same | Windowed EPROM (UV-erasable, prototype/debug) | OTP - same |
Ключевые отличия
- Industrial temperature range with same silicon as E/L variant (против PIC17C756AT-33E/L)
- OTP rather than windowed EPROM (против PIC17C756AT-33I/CL)
- Pin-compatible with the broader PIC17C family migration path (против PIC18F6520)
Заметки по проектированию
Decouple every VDD/VSS pair on the 68-pin PLCC with a 100 nF X7R ceramic placed as close to the package pin as possible; add a single 10 uF bulk tantalum or aluminum-polymer capacitor at the board's 5V entry. The PIC17C756AT-33I/L has multiple VDD/VSS pins distributed around the package to reduce internal ground bounce, and each one must be individually bypassed - relying on a single bulk cap will cause ADC noise and I/O glitches at high switching rates.
Place the 33 MHz crystal or resonator within 10 mm of the OSC1/OSC2 pins with short, symmetric traces and a guard ground ring. Keep digital switching traces (especially PWM and USART lines) away from the analog AN0-AN11 inputs and the AVDD/AVSS pair. If the design mixes analog and digital ports, route analog signals with a ground-shielded microstrip and place a small RC filter (10 ohm + 100 pF) on each ADC input to suppress transient injection from nearby digital edges.
Because the PIC17C756AT-33I/L is OTP, firmware bugs cannot be fixed in-circuit; every code revision requires a new device. Mitigate this by developing and qualifying firmware on the PIC17C756AT-33I/CL ceramic-windowed part (same silicon, UV-erasable), then transferring the verified image to OTP for production. Always order a small prototype batch of OTP parts and run full functional tests before committing to volume.
Estimated: at VDD = 5V and 33 MHz with all 50 I/O switching, supply current is approximately 50 mA (per datasheet ICC typical); power dissipation is therefore approximately 0.25 W, well within the 68-PLCC's thermal envelope (theta_JA around 50 C/W). At elevated ambient (>70C), verify junction temperature rise with a thermal probe in the application's worst-case I/O profile; the -40C to +85C industrial range provides adequate margin for cabinet-mounted designs.
Информация о соответствии
68-pin PLCC package historically uses SnPb (tin-lead) finish and is not RoHS compliant; PIC17C756A family is not AEC-Q100 qualified. For new RoHS or automotive designs, migrate to PIC18F6520 (RoHS, flash) or PIC18F46K22 (AEC-Q100).
